Eldat WSD01 User manual

Model
WSD01-04A01
Technical data
Supply voltage: max. 11.5 - 20.5 V DC
via DALI-Bus
Connection: Spring terminal
Line 0.2 - 0.75 mm²
rigid or exible
Current consumption: 17 mA
Operating temperature: -20 °C to +60 °C
Dimensions: Key: 55x55x9 mm or
Keys: 27x55x9 mm
Mounting plate:
71x71x1.5 mm
Weight: 30.0 g
System requirements: Windows Vista, 7, 8, 10
USB 1.1 or higher
10 MB free hard drive space
Scope of delivery
DALI module, mounting plate, 1x single-button unit, 2x
serial button unit, attachment set, operating instructions
Intended use
The device must only be used as a wall-mounted button unit
for controlling DALI end devices.
The manufacturer is not liable for any damage caused by
improper or unintended use!
Safety information
Before connecting this device, please read these
instructions carefully!
Observe any applicable laws, standards and regulations
as well as manufacturer instructions pertaining to the de-
vices being connected!
Have any malfunctioning devices inspected by the manu-
facturer!
Do not perform unauthorised modications to the device!
Function
The DALI wall-mounted button unit enables up to four DALI
functions to be triggered via the DALI bus. (DALI: Digital Ad-
dressable Lighting Interface).
When using one-button operating modes, a maximum of four
DALI devices or four DALI groups can be addressed.
When using two-button operating modes, the number of ad-
dressable devices or groups is reduced to two.
It is also possible to simultaneously control all devices on the
DALI bus (broadcast) in any mode.
WSD01 Wall-mounted button unit DALI
D
The WSD01 DALI wall-mounted button unit can be used as a
single-button controller or as a serial button controller.
The "WSD01 Congurator" software is used to allocate indi-
vidual functions to the individual buttons.
Each individual button can have a function allocated to it:
- DIM two-button operation,
- ON/OFF two-button operation,
- DIM one-button operation,
- ON/OFF one-button operation,
- Open SCENE,
- SKIP through scenes,
- DEAD MAN'S SWITCH one-button operation,
- Fixed dimmer setting.
The function “DIM two-button operation” is congured as a
factory preset for broadcasting to all DALI devices on the
bus.
This enables the wall-mounted button unit to be used on the
DALI bus without any prior programming using the “WSD01
Congurator”.
The RGD-ACC-01 set-up cable (including “WSD01 Congu-
rator”) is required to modify function and address allocations.
This is not included with the product and must be ordered
separately.
Connecting the wall-mounted button unit with
the PC
To enable the DALI wall-mounted button unit to be cong-
ured using the PC, the RGD-ACC-01 set-up cable is re-
quired (see Figure 1).
1. Remove the cover panel and the WSD01 from the
mounting plate if necessary.
2. Insert the enclosed programming adapter into the DALI
end of the set-up cable.
3. Connect the 4-pin programming adapter to the rear of
the WSD01. The connectors are protected from being
inserted the wrong way around.
4. Insert the USB plug of the set-up cable into a free USB
port on the PC.
5. Install and launch the "WSD01 Congurator" congu-
ration software.
Single-button
controller
Serial button
controller
E
F
A
B1
D
B2
I
(siehe Abb. 1)
A Button(s)
B1 DALI module, front
B2 DALI module, rear
DCover frame,
cut-out dimensions 55x55 mm
(not included in scope of delivery)
EMounting plate
FClip
GProgramming adapter
H Programming cable RGD-ACC-01
I Connection terminal (DALI terminals)
(recommended removal tool: SMDat WKZ)
PC
Fig. 1
Power supply DALI bus
G
H
Disposal
Waste electronic equipment must not be disposed of
with household waste!
Dispose of the waste equipment via collection
facilities for electronic scrap or via your special-
ist dealer.
Dispose of packaging material in the recycling
bins for cardboard, paper and plastic.
Warranty
Within the statutory warranty period, we undertake to rectify
free of charge by way of repair or replacement any product
defects arising from material or production faults.
Any unauthorised tampering or modications will render this
warranty null and void.
Conformity
Hereby, ELDAT GmbH declares that the radio equipment
type WSD01 is in compliance with Directive 2014/53/EU.
The full text of the EU declaration of conformity is available
at the following internet address: www.eldat.de
Customer service
If, despite proper handling, the device does not work prop-
erly or if the device has been damaged, please contact the
manufacturer or your retailer.
ELDAT GmbH
Im Gewerbepark 14
15711 Königs Wusterhausen / Germany
Phone: + 49 (0) 33 75 / 90 37-310
Fax: + 49 (0) 33 75 / 90 37-90
Internet: www.eldat.de
Email: [email protected]
Preparing the wall-mounted button unit for operation
General information
1. Attach the mounting plate to the installation location
using the enclosed screws & wall plugs or the adhesive
pads.
2. Connect the WSD01 to the DALI bus via the DALI termi-
nals on the rear. The direction is interchangeable.
3. Place the cover frame on the mounting plate and lock
the DALI module into place at the top and bottom onto
the clips. The arrow on the module must be pointing
upwards.
4. Plug your chosen button unit (single-button or serial
button controller) onto the transmitter module.
5. (optional) Program the functions and addressing of
the WSD01 using the RGD-ACC-01 set-up cable and
"WSD01 Congurator".

WSD01 Congurator
Installation
1. Insert the “Easywave DALI Gateway” CD into your CD
drive.
2. Execute the program “WSD01_Setup.exe” in the root
directory and follow the instructions during installation.
3. Launch the “WSD10 Congurator”.
The installation les can also be downloaded from our
website:
http://www.eldat.de/schnittstellen/wsd01e_de.html
Conguring the language
You can use the menu item “Language” to switch between
English and German at any time.
The language set in the operating system is used by default.
Establishing a connection with the WSD01
1. Connect the PC/laptop using the set-up cable to the
WSD01. The WSD01 must remain connected to the
DALI bus and must remain powered for the entire con-
guration process!
2. Click on the “Connect” button in the “WSD01 Congu-
rator”. A green tick must appear after “USB Dongle” and
“DALI Wall-Mounted Button Unit”! If these ticks are not
present, restart the program.
The conguration of the currently connected WSD01 is im-
ported automatically upon connection.
Conguring the DALI functions
In the top area of the program window, it is rst established
whether the WSD01 is being used with one button or two
buttons. This setting is dependent on the number of switches
mounted on the button unit (one or two).
If "1 switch" is selected, only the left area will be available for
DALI conguration. If "2 switches" has been selected, both
the left and right area will be available.
A dedicated combination of mode and DALI address for the
DALI devices to be controlled can then be congured for
each button position of the wall-mounted button unit. The
button positions of the wall-mounted button unit can be al-
located to the individual areas as follows:
Switch 1 - A: Top left
Switch 1 - B: Bottom left
Switch 2 - A: Top right
Switch 2 - B: Bottom right
In the current conguration, unusable button positions are
greyed out.
If a mode with two-button operation is selected, the corre-
sponding button positions will be allocated automatically and
the relevant area will be greyed out.
With one-button operation modes on the other hand, it is
possible to congure a dedicated function to each button
position.
Once you have created the desired conguration, click on
“Transfer” to transfer the data to the WSD01 wall-mounted
button unit.
If there are changes that have not yet been transferred, this
will be indicated at the bottom left with "Changes made".
In this case, the conguration should be transferred again.
The message "Transfer data" will appear at the bottom
left.
The conguration process is now complete and you can dis-
connect the USB cable from the gateway. The WSD01 is
ready for operation.
UM160422 0917 D
Available modes
DIM two-button operation
This mode enables the brightness of DALI devices to be
dimmed or increased.
A short press of the button switches the supplied devices on
to 100% (top) or switches them off to 0% (bottom).
Holding down the button will dim or brighten the supplied
devices.
ON/OFF two-button operation
The controlled DALI devices are switched as desired to ON
(top) or OFF (bottom).
DIM one-button operation
The controlled DALI devices are alternately dimmed or
brightened using the very same button position.
A short press of the button switches the supplied devices ON
to 100% or switches them OFF to 0%.
Holding down the button will alternately dim or brighten the
supplied devices.
ON/OFF one-button operation
The DALI devices are alternately switched ON or OFF using
the very same button position.
Open SCENE (one-button operation)
A scene that is stored in the DALI device is triggered. The
desired scene (0–15) must be set in the drop-down menu
“Scene”.
SKIP through scenes (one-button operation)
Each press of the button skips ahead by one scene within a
pre-dened scene range.
This range is set in the drop-down menu “Scene” and gener-
ally begins with Scene 0, ending at a maximum of Scene 15.
DEAD MAN'S SWITCH one-button operation
The controlled DALI devices are switched on as long as the
button is held down.
Fixed dim setting (one-button operation)
A xed dim setting specied as a percentage is transferred to
the addressed DALI devices. This setting can be congured
in increments of 1% to any value between 0% and 100%
using the sliders.
Addressing
When using a mode with one-button operation, each of the
two button positions of a switch (top and bottom) can trigger
a separate DALI address.
If a mode with two-button operation is being used, each
switch can only trigger one DALI address. In this case, the
bottom button positions are allocated automatically, which
is why modes with two-button operation cannot be selected
here.
It is possible to control either ALL devices (broadcast), indi-
vidual devices or groups of devices.
To do this, select the relevant item in the “Devices” section,
then select the desired address in the corresponding drop-
down menu.
Individual devices can be controlled in the address range
0–63.
Groups can be controlled in the range 0–15.
Saving and loading the conguration
You can use the menu item “File” to save the current con-
guration on the PC or laptop or import a previously saved
conguration into the “WSD01 Congurator”.
Please note that a loaded conguration must rst be trans-
ferred to the wall-mounted button unit by clicking on “Trans-
fer” before it becomes active.