Electro-Voice ID60D-8 User manual

ID60D-8
ID60DT
Heavy-Duty
Compression Drivers
General Product Description
The ID60D-8 and ID60DT are heavy-duty compression
drivers for use in high-power public address installations.
The drivers employ rugged phenolic diaphragms, 2-inch
diameter voice coils and “rim centered” ferrite magnet
structures for long life and reliability under extreme operating
conditions.
A hinged cycolac rear housing for easy access and
connection to a sound system, via a BX conduit connector,
is provided together with a plug-in, field replaceable
diaphragm assembly.
The transformer model (ID60DT) includes connections for
25-V and 70-V distributed systems and a screwdriver
operated power-tap select switch.
The exterior is finished in durable, weatherproof paint, and
all metal parts have been tropicalized for resistance to high
humidity and fungus.
Ideal for both indoor and outdoor applications, these drivers
are well suited for any installation requiring rugged,
high-power performance.
Architects’ and Engineers’ Specifications
The loudspeaker(s) shall be of the compression-driver type
utilizing a rugged phenolic diaphragm and a
high-temperature rated, 2-in. diameter voice coil.
The loudspeaker(s) shall exhibit essentially flat power
response from 300 to 4,000 Hz with a smoothly rolled-off
response beyond. Their sensitivity, when mounted on a PH
horn, will be 108 dB (1 W/1 m) with a 500- to 5,000-Hz
pink-noise signal applied.
Specifications:
Frequency Response:
............................................. 300 - 4,000 Hz ±5 dB (see Figure 2)
Power Handling, 8 Hours, 6-dB Crest Factor:
............................................... 60 watts (500-5,000 Hz pink noise)
Impedance, Nominal: ...................................................... 8 ohms
Minimum:7.5 ohms (Cobraflex Horns above 500 Hz)
Sound Pressure Level at 1 Meter, 1 Watt Input Averaged, Pink
Noise Band-Limited from 300-3,000 Hz:
..................................................................................... See Table I
Voice Coil Diameter: .......................................... 5.08 cm (2.0 in.)
Magnet Weight: ................................................... 0.48 kg (1.06 lb)
Magnet Material: ................................................ Strontium ferrite
Flux Density: ............................................................... 1.17 Tesla
Construction:
Rugged diecast housing with weatherproof finish for outdoor
use
Mechanical Construction of Driver:
1 3/8"-18 thread, 1/2 long allows the ID60 to be mounted on
any University Sound horn.
Dimensions:
Diameter: ..................................................... 14.3 cm (5.6 in.)
Height: .......................................................... 16.2 cm (6.4 in.)
Net Weight:
ID60D-8: .................................................. 2.7 kg (5.9 lb)
ID60DT: .................................................. 3.4 kg (7.4 lb)
Shipping Weight:
D60D-8:: .................................................. 2.9 kg (6.3 lb)
ID60DT: .................................................. 3.6 kg (7.9 lb)
Recommended Horns:
Cobreflex IIB, Cobreflex III, PH, 2WP, SMH, SH
COMMERCIAL
The loudspeaker(s) shall be capable of handling a 60-watt,
500- to 5,000-Hz pink-noise signal with a 6-dB crest factor
for a period of 8 hours.
The loudspeaker(s) shall have a diameter of 14.3 cm (5.6
in.) and a depth of 16.2 cm (6.4 in.) They shall have a 2.41
cm (0.95 in.) throat opening with a 1 3/8-18 thread for
mounting.
The loudspeaker shall be the ID60DT, which includes a 70-V/
25-V line-matching transformer and weighs no more than 3
4 kg (7.4 lb), and the ID60D-8, which has a nominal
impedance of 8 ohms and weighs no more than 2.7 kg (5.9
lb).

© Telex Communications, Inc. 02/2001
Part Number 38109-855 Rev A
U.S.A. and Canada only.
For customer orders, contact the Customer Service department at
800/392 3497 Fax: [phone]
For warranty repair or service information, contact the Service
Repair department at 800/685 2606
For technical assistance, contact Technical Support at 866/78 AUDIO
Please refer to the Engineering Data Sheet for warranty information.
Specifications sub ect to change without notice.
Installation
Remove the plastic cap from the threaded throat of the driver and screw
the driver into the horn until firmly seated.
Install the horn/driver assembly in intended location, referring to the
instructions provided with the horn.
Loosen the captive screw in the center of the plastic cover at the rear of the
driver, and open the hinged cover to expose wiring. Note the O-ring in the
annular housing groove.
Loosen the gland nut in the side of the driver housing enough to admit the
loudspeaker wire/cable. Alternately, a 1/2-inch conduit fitting can be
substituted for the gland nut. However, the sealing washer must be retained.
For the ID60DT, connect the loudspeaker wires to the “com” terminal and
the appropriate line terminal (25 V or 70 V). For the ID60D-8, connect to the
“com” and “8-ohm” terminals.
Tighten the gland nut securely and check that the O-ring is positioned
correctly before closing the clear plastic cover.
Low-Frequency Driver Protection
When frequencies below the low-frequency cutoff for the horn assembly
are fed to the driver, excessive current may be drawn by the driver. For
protection of driver, amplifier, and transformer (if driver with built-in
transformer is used), capacitor(s) in series with driver, or transformer primary
are recommended. Table I indicates recommended values. The values
Figure 1.
Disortion Response - Plane Wave Tube (1 inch)
(6 watt input)
Figure 2.
Disortion Response - FC100 Horn
Figure 3.
Impedance Response - Plane Wave Tube (1 inch)
Figure 4.
Impedance Response - FC100 Horn
shown are for 200 Hz. Values for other frequencies can be determined by
using the formula:
For drivers without transformers: 8-ohm driver, 25 V - 100 mf 150 Vdc or
150 V non-polarized electrolytic, or two 150 Vdc electrolytics of two times
required value in series, back to back, for 70 volt lines.
seniLtloV-07seniLtloV-52
rewoPecnadepmIecnaticapaCecnadepmIecnaticapaC
W06smho3801
fm smho0108 fm
W03smho6615 fm smho1204 fm
W51smho3332 fm smho2402 fm
W5.7smho7661 fm smho3801 fm
W57.3smho003,15.0 fm smho6615 fm
W88.1smho007,22.0 fm smho3332 fm
C = [C200 x 200 ]
C200 Values shown in the following table
f f = New Frequency
Table II. Series Protection Capacitors for 200 Hz and Below
USA 12000 Portland Ave South, Burnsville, MN 55337, Phone: [phone], FAX: [phone]
Canada 705 Progress Avenue, Unit 46,Scarborough, Ontario, Canada, M1H2X1,Phone: [phone], FAX: [phone]
Switzerland Keltenstrasse 11, CH-2563 IPSACH, Switzerland, Phone: [phone]. FAX: [phone]
Germany Hirschberger Ring 45, D94315, Straubing, Germany, Phone: [phone], FAX: [phone]
France Parc de Courcerin, Alle Lech Walesa, Lognes, 77185 Marne La Vallee, France, Phone: [phone], FAX: [phone]
Australia Unit 23, Block C, Slough Business Park, Slough Avenue, Silverwater, N.S.W. 2128, Australia, Phone: [phone], FAX: [phone]
Hong Kong Unit E & F, 21/F, Luk Hop Industrial Bldg., 8 Luk Hop St., San PO Kong, Kowloon, Hong Kong, Phone: [phone], FAX: [phone]
Japan 2-5-60 Izumi, Suginami-ku,Tokyo, Japan 168, Phone: [phone], FAX:[phone]
Singapore 3015A Ubi Rd 1, 05-10, Kampong Ubi Industrial Estate, Singapore 408705, Phone: [phone], FAX: [phone]
Mexico Av. Parque Chapultepec #66-201, Col. EI. Parque Edo. Mex. 53390, Phone: [phone], FAX: [phone]
UK 4, The Willows Centre, Willow Lane, Mitcham, Surrey CR4 4NX, UK, Phone: [phone], FAX: [phone]
Africa, Mid East 12000 Portland Ave South, Burnsville, MN 55337, Phone: [phone], FAX: [phone]
Latin America 12000 Portland Ave South, Burnsville, MN 55337, Phone: [phone], FAX: [phone]
www.electrovoice.com • Telex Communications, Inc. • www.telex.com
nroHM1@W1rofLPS
BIIxelferboCBd701
IIIxelferboCBd701
Table I. Sound Pressure Level for ID60 with Various Horns