Electrolux 6000 Operating instructions

Essentia
Suggested for you
For more Accessories & Consumables
please look at our Catalogues or contact
our Electrolux Service Partner.
Line 6000
Tumble Dryers
every
3
months
6Check the drain and the
drain pipe are not obstructed
(for heat pump models)
every
3
months
5Check that the air intake is
not obstructed by dirt and
clean it if necessary
daily
4Check that the door gaskets
are clean and not damaged
every
3
months
7Clean the surface of the drum with
citric acid and, if necessary, an
abrasive sponge making sure that
any recidues are taken off
daily
2Clean the filter by removing the lint.
During intensive use, even after
every cycle
per
1week
3When the notification is displayed,
check that the second lint filter is clean
(remove the lint) and not damaged
daily
1Remove any lint around
the machine
0W1Y2F
Stainless Steel
Trolley BV-220 /
BV-131lt
0W1XFY
Canvas Trolley
RV-74 - 200 lt
0W21DK
Soft Care
sheets to soften
and scent your
laundry, 30 pcs
0W21DH
Dryer balls
2 pieces
1
0W1Y2C
Bulk Transport
Cart HV-52
0HM803
Brush with
chain - 850mm
Cleaning external surfaces
Wash the external surfaces with warm, soapy water. Avoid using detergents containing abrasive substances, steel wool, brushes or
steel scrapers. Rinse with a damp cloth and dry carefully. Avoid using chlorine or ammonia-based products. Clean the control panel
with a soft cloth dampened with water and, if necessary with neutral detergent. Do not wash the equipment with direct or high pressure
jets of water. With the aim of reducing the emission of polluting substances into the atmosphere, it is advisable to clean the equipment
(externally and, when neccessary, internally) with products that have a biodegradability exceeding 90%. Electrolux Professional
strongly recommends to use Electrolux Professional approved cleaning agents, rinse and descaling agents to obtain better results
and maintain product efficiency over time. Damages caused by cleaning, as a consequence of use of not approved cleaning agents,
rinse and descaling, will be excluded by the warranty.
The operations described must be performed wearing the needed Personal Protection Equipment. Refer to the User Manual.
05UMW04___ENG00L6
User maintenance guide
6
5
2
4
7
3
Planned Maintenance Programmes
In order to ensure the safety and performance of your equipment,
it is recommended that regular service is undertaken every
12 months by Electrolux Professional authorised engineers
in accordance with the manufacturer recommendations.
Please contact your local Electrolux Professional Service
Centre for further details of service agreements available.
2020-04-02

Anomaly Description Instructions to User
12:1 Machine indicates that Inlet air over heat protection
has cut out Switch off power to the machine and contact authorized service
12:2 Machine indicates that Outlet air over heat protection
has cut out Push the control knob to restart the program
12:8
(for condense
models)
Machine indicates that condense water tank has
not been drained within set time
1. Turn the machine off and on again. Condensate pump will start
2. If water is coming out of the condensate drain hose, it might be
partly blocked. Contact authorized service
3. If the pump is running and no water coming out the drain is
blocked. Contact authorized service
12:11 (for models
with RMC system)
Machine indicates garment is not dry within max drying
time (RMC)
1. Check that the dryer is not overloaded
2. Open the door to reset the error message
12:12 (for models
with RMC)
Machine indicates garment is not dry within max drying
time (AUTOSTOP)
1. Check that the dryer is not overloaded
2. Check that the garments are not loaded too wet after extraction)
3. Open the door to reset the error message
12:13 (for models
with RMC)
Machine indicates garment is not dry within max drying
time (TIME) Open the door to reset error message
12:14
(for gas models)
Machine indicates flame sensor is not detecting gas
flame within set time
Reset the error message by a short push on the control knob
Check the gas supply
12:15 Machine indicates vacuum switch is not activated
within set time
Check that machine is not overloaded
Check that Doors are closed and seals are in good order
Press the control knob to clear error message and restart program
12:18 Machine indicates vacuum switch has deactivated
several times during program run
Redistribute the load in the drum
Press control knob to clear message and restart the program
12:19 (Heat Pump
models) Machine indicates blocked air flow in heat pump unit Clean lint filter Press control knob to clear message and restart the program
12:253 Machine indicates that Jumper 1 is missing Press control knob to clear message and restart the program
17:20 (Heat Pump
models) Machine indicates critical error in heat pump unit Switch off power to the machine for 5 minutes and then on again Try to start a new program
17:21 (Heat Pump
models) Machine indicates internal error in heat pump unit Switch off power to the machine for 5 minutes and then on again Try to start a new program after HP initializing has finished
20:1 Machine indicates drum motor is overheated Wait 30 minutes to allow the motor to cool down
Press the control knob to clear error message
30:1 Machine indicates fan motor overheated Wait 30 minutes to allow the motor to cool down
Press the control knob to clear error message
Essentia