Electrolux TT300 Specification sheet

Operating and installation manual
TT300 – TT500 – TT750
487 1839 51/01
99.31

487 18 39 01 - 300/500/750 - GB
WARNING:
For your safety the information in this
manual must be followed to minimise the risk of fire
or explosion or to prevent property damage,
personal injury or loss of life.
Do not store or use gasoline or other flammable
vapours and liquids in the vicinity of this or any other appliance.
WHAT TO DO IF YOU SMELL GAS
• Do not try to light any appliance.
• Do not touch any electrical switch; do not use any phone in your building.
• Clear the room, building or area of all occupants. Immediately call your gas
supplier from a neighbour’s phone.
Follow the gas supplier’s instructions.
• If you cannot reach your gas supplier, call the fire department,
Installation and service must be performed by a qualified installer, service agency
or the gas supplier,
For replacement parts, contact the distributor from which the dryer was purchased.
Tumble dryer
Gas dryers only
3

487 18 39 01 - 300/500/750 - GB
Contents:
Instructions for use: ................................................................................ 7
Diagram of tumble dryer
Operating panels
Maintenance
General installation:.................................................................................19
Reversing door. Setup
Venting
Error codes
Running hours counter
Installation electric, steam and gas heating:........................................27
Dimension sketch
Technical data
Electric installation, function check,
Fuse sizes, effects and voltages
Instructions for steam installation
Gas installation
Parameter programming: ........................................................................45
Switching to programming mode
Adjustable parameters, change machine type
Temperature and time setting, reversing
Cooling time, residual moisture level, extra drying time
Quick view parameter list.
Remember that such textiles as silk and wool must not be dried
in the tumbler.
The manufacturer reserves the right to modify design and material
specifications without notice.
Tumble dryer
Safety instructions
This machine is only intended for drying water-washed gar-
ments.
The machine must not be used for drying foam rubber or
foam-like materials.
The machine must not be used for drying floor mops*.
The machine must not be used by children.
The machine must not be hosed down with water.
Mechanical, electrical and gas installations must only be car-
ried out by qualified personnel.
If the machine has a fault, this must be reported as soon as
possible to the person in charge. This is important for your
own safety and for the safety of others.
Machine with gas heating is not to be installed in rooms con-
taining cleaning machines with PERCHLOROETHYLENE,
TRICHLOROETHYLENE or CHLOROFLUOROCONTAINING
HYDROCARBONS as cleaning agents.
*Applies only to mop heads containing polypropylene.
5

Instructions for use 7
487 18 39 01 - 300/500/750 - GB
Diagram of tumble dryer
Door
Drum
Filter door
Operating panel

Instructions for use
8
487 18 39 01 - 300/500/750 - GB
AG H
B
CE
F Jb a
DI
Manual operational
Industrial laundry OPL (on-premises-laundry)
A. Filter:Filter: when the lamp is lit, the filter must be cleaned
B. Display indicates drying time/time remaining
C. Operating lamp
D. Timer button for setting drying time
E. Start/stop button
F. Temperature selection button
G. Lamps: lit to indicate selected temperature
H. Temperature
I. Gasheated: Push button with light indicator for resetting
gas control
On machine with reversing:
J. Reversing switch: a = With reversing.
b= Without reversing.
Warning
If the gas flame is not ignited
within 10 seconds after starting
the tumble dryer the gas con-
trol will automatically turn off
the gas and report an error.
Push button (I) will be lit.
After 15 seconds it is possible
to reset the error by pushing
the push button (I).
If the situation arises that it is
necessary to reset more than 2
times in a row on the push but-
ton (I) a service technician
must be called in to check the
machine.

Instructions for use 9
487 18 39 01 - 300/500/750 - GB
Manual operational
Industrial laundry OPL (on-premises-laundry)
Check that
the filter is
clean
Select
drying
time:
Set the
timer to the
desired
time.
High:70 - 85°C non-iron/normalwash
cotton and mixed fabrics.
Drying at normal heat.
Low: 50°C Fine wash/mild wash,
Delicate fabrics. Drying at low heat.
No heat:
suitable for airing bedspreads, duvets
and bedclothes, etc.
Start:
Press the start/stop
button
Stop:
Press the
start/stop button or
open the door.
Take care!
Garments may fall
out when the door
opens.
The last few minutes of the
drying time are the cooling-down
period
(the garments are cooled).
To prevent
creasing:
Empty the tumble
dryer as soon as
the program has
ended.
If the tumble dryer is not emptied
immediately after the drying time has
ended, an anti-crease programme is
automatically engaged.
This means that the drum rotates at short
intervals, thereby almost completely
avoiding creasing.
15 - 35
minutes
Drying programme
with heat:
Airing: Approximately 10 minutes
The tumble-dryer
stops
automatically
when the selected
drying time has
ended.
Restart:
Close the door
again and press
the start/stop
button.
Load
garments
into the
machine.
85°C
70°C
50°C
Select
tempe-
rature

Instructions for use
10
487 18 39 01 - 300/500/750 - GB
Manual operation with RMC (residual moisture control)
Industrial laundry OPL (on-premises-laundry)
AG H
B
CE
F Jb a
DI
A.Filter: When the lamp is lit, the filter must be cleaned.
B.Display indicates program: P1, P2, P3 – or in time
control version: drying time/time remaining
C.Operating lamp.
D. Program selection button/drying-time adjuster.
E. Start/stop button.
F. Temperature selection button.
G. Lamps: lit to indicate selected temperature.
H. Temperature.
I. Gasheated: Push button with light indicator for
resetting gas control
On machine with reversing:
J. Reversing switch: a = With reversing.
b= Without reversing.
124 5
33
15-90 MIN15-90 MIN
Warning
If the gas flame is not ignited
within 10 seconds after starting
the tumble dryer the gas con-
trol will automatically turn off
the gas and report an error.
Push button (I) will be lit.
After 15 seconds it is possible
to reset the error by pushing
the push button (I).
If the situation arises that it is
necessary to reset more than 2
times in a row on the push but-
ton (I) a service technician
must be called in to check the
machine.

Instructions for use 11
487 18 39 01 - 300/500/750 - GB
Manual operation with RMC (residual moisture control)
Industrial laundry OPL (on-premises-laundry)
Check that
the filter is
clean
Start:
Press the start/stop
button
Stop:
Press the
start/stop button or
open the door.
Take care!
Garments may fall
out when the door
opens.
The last few
minutes of the
drying time are
the cooling-down
period
(the garments are
cooled).
Restart:
Close the door
again and press
the start/stop
button.
Load
garments
into the
machine.
If the tumble dryer is not emptied after
the drying time has ended, an anti-wrinkle
program is automatically started.
This means that the drum rotates at short
intervals, thereby almost completely
avoiding creasing.
To prevent
creasing:
Empty the tumble
dryer as soon as
the program has
ended.
High: 70 - 85°C non-iron/normal wash,
cotton and mixed fabrics.
Drying at normal heat.
Low: 50°C Fine wash/mild wash,
Delicate fabrics. Drying at low heat.
No heat:
suitable for airing bedspreads, duvets
and bedclothes, etc.
85°C
70°C
50°C
Select
tempe-
rature
15-90 MIN
Select the
program:
P1, P2, P3
or
timer, from
15 to 90
minutes
Extra dry
Ready-to-put-away
Ironing-dry
Time control, in minutes,
(15–90).
Strong fabrics:
the machine stops
automatically when
the garments are
extra dry
Uniform fabrics:
The machine stops
automatically when
the garments are
ready to put away
Ironing.:The
machine stops
automatically when
the garments are
ironing dry
(slightly moist).
15-90 MIN
Time control.
The machine stops
when the selected
time has ended.
Drying time:
15–90 minutes.

Instructions for use
12
487 18 39 01 - 300/500/750 - GB
A B C D
FGH I J
E
K
1234 5
A.Display indicates drying time/time remaining
B. Filter: when the lamp is lit, the filter must be cleaned
C. Lamps: lit to indicate selected temperature
D. Temperature
E. Coin insertion (one ore double insertion)
F. Operating lamp
G. Timer button not active on coin-operated machines
H. Start/stop button
I. Temperature selection button
J. Jammed coin return button
K. Returned coins
Coin operation

Instructions for use 13
487 18 39 01 - 300/500/750 - GB
Coin operation
Insert coins
until the desired
drying time is
indicated on
the display
before starting.
Start:
Press the
start/stop button
The tumble dryer
stops
automatically
when the paid
drying time has
ended
15 - 35
minutes
Drying programme with
heat:
Airing: Approximately
10 minutes
Load
garments
into the
machine.
High: 70 - 85°C non-iron/normal wash,
cotton and mixed fabrics.
Drying at normal heat.
Low: 50°C Fine wash/mild wash,
Delicate fabrics. Drying at low heat.
No heat:
suitable for airing bedspreads, duvets
and bedclothes, etc.
85°C
70°C
50°C
Select
temperature
Stop:
Press the
start/stop button or
open the door.
Take care!
Garments may fall
out when the door
opens.
Restart:
Close the door
again and press
the start/stop
button.
The last few minutes of the
drying time are the cooling-down
period
(the garments are cooled).
To prevent
creasing:
Empty the tumble
dryer as soon as
the program has
ended.
If the tumble dryer is not emptied
immediately after the drying time has
ended, an anti-crease programme is
automatically engaged.
This means that the drum rotates at short
intervals, thereby almost completely
avoiding creasing.

Instructions for use
14
487 18 39 01 - 300/500/750 - GB
A. Filter: When the lamp is lit, the filter must be cleaned.
B. Not active on machines controlled by a central control panel.
C. Operating lamp/indicator: Ready to start.
D. Timer button, not active on payment machines.
E. Start/stop button.
F. Temperature selection button.
G. Lamps: lit to indicate selected temperature.
H. Temperature.
1234 5
GH
A
D E F
B
C
Machine controlled by a central control panel (CP)

Instructions for use 15
487 18 39 01 - 300/500/750 - GB
Machine controlled by a central control panel (CP)
Pay for the desired
drying time on
the central
control panel
Load
garments
into the
machine.
Start:
Press the
start/stop button
Stop:
Press the
start/stop button or
open the door.
Take care!
Garments may fall
out when the door
opens.
The last few minutes of the
drying time are the cooling-down
period
(the garments are cooled).
To prevent
creasing:
Empty the tumble
dryer as soon as
the program has
ended.
If the tumble dryer is not emptied
immediately after the drying time has
ended, an anti-crease programme is
automatically engaged.
This means that the drum rotates at short
intervals, thereby almost completely
avoiding creasing.
The tumble dryer
stops
automatically
when the paid
drying time has
ended
Restart:
Close the door
again and press
the start/stop
button.
When the lamp
flashes,
the machine is
reserved and
ready to start
High: 70 - 85°C non-iron/normal wash,
cotton and mixed fabrics.
Drying at normal heat.
Low: 50°C Fine wash/mild wash,
Delicate fabrics. Drying at low heat.
No heat:
suitable for airing bedspreads, duvets
and bedclothes, etc.
85°C
70°C
50°C
Select
tempe-
rature

Instructions for use
16
487 18 39 01 - 300/500/750 - GB
Maintenance
The following should be carried out at regular
intervals, depending on the operating frequency.
Daily
• Check that the drum stops when the door is
opened.
• Check that the machine does not start until the
start button has been activated.
• Check whether the door packing has been
cleaned (use a moist cloth).
• Cleaning of filter compartment:
Remove the door by opening it and pulling it
upwards. It is not necessary to remove the lint fil-
ter for cleaning. The air system of the machine
ensures that lint and dust settle automatically at
the bottom of the filter compartment, from where
they are removed by means of a hand-held broom
or a vacuum-cleaner.
• Check that the lint filter is unbroken.
Quarterly/Semi-annually
• Check that the fresh-air intake at the back of the
machine is not clogged by lint or otherwise
blocked.
• Check that the exhaust system connections are
tight and that the ducts are not clogged by lint or
dust or otherwise blocked.
• Check that the fan wheel is not clogged by lint or
otherwise blocked.
1
12
2
3
3
To be continued

Maintenance continued
Annually
•Check that the fresh-air intake to the room and
evacuation ducts/pipes in and from the room is not
clogged by lint or dust or otherwise blocked.
Carry out cleaning/cleansing at a frequency that
depends on the operating load - once a year as a
minimum.
• Dismount front panel and finger protector.Clean for
lint/dust
• At least once a year a skilled expert should check
the inside wearing parts of the machine and clean
them of lint.
Lubrication
The motor bearings, idler bearings, and main
bearings are permanently lubricated.
No lubrication is necessary
Maintenance only for steam heating
Cleaning the filter in front of steam battery
•Open the front panel.
• Remove the filter as shown (A).
• Clean the filter with water or with compressed air.
• Replace the filter and close front panel
The filter ought to be cleaned at least once a week.
Instructions for use 17
487 18 39 01 - 300/500/750 - GB
A
11
4
1
4
1

Instructions for use
18
487 18 39 01 - 300/500/750 - GB

General installation 19
487 18 39 01 - 300/500/750 - GB
2
3
500
10
Setup, 300/30 and 500/50
Unpacking
When unpacking the machine, handle it with
care. There are no transport clamps.
Positioning
Position the tumble dryer so that there is plenty
of room for working, both for the user and for
the service technician.
The distance from the wall or other equipment
behind the tumble dryer should be at least 500
mm and the space at the sides at least 10 mm.
Note that, for servicing purposes, access to the
rear of the tumble dryer is required.
Mechanical installation
Adjust the machine to make it stand horizontally
and stably on all four feet.
The max. height adjustment of the feet is 15
mm.
2
3
10
Reversing door
The tumble dryer is usually delivered with a right
hinged door but the door can easily be changed to
left hinged position.
Reversing
Disconnect the power supply to the machine.
Unscrew the door and the front panel.
Move the microswitch and the wires to the opposite
side.
Turn the front panel and the door and mount them
again.
Unscrew the door pin and move it to the position A.
Connect the power to the machine and check the
door.
Start the machine.
Check that the safety lock is working:
The drum, ventilator and heat must stop if the
front door is opened as much as 50 mm.
11
1
1
A

General installation
487 18 39 01 - 300/500/750 - GB
20
1
3
2
4
500
10 10
Setup 750/75/650
Unpacking
When unpacking the machine, handle it with
care. There are no transport clamps.
The tumble dryer is fastened to the pallet by
four screws. Remove the two front screws by
opening the filter panel. Remove the two back
screws by unscrewing and removing the bottom
back-plate.
Carefully push the tumble dryer back so that it
can be tipped backwards to allow the pallet to
be pulled out from beneath it.
Put the tumble dryer into position, tipping it up
to allow the four supplied feet to be fitted.
Positioning
Position the tumble dryer so that there is plenty
of room for working, both for the user and for
the service technician.
The distance from the wall or other equipment
behind the tumble dryer should be at least 500
mm and the space at the sides at least 10 mm.
Note that, for servicing purposes, access to the
rear of the tumble dryer is required.
Mechanical installation
Adjust the machine to make it stand horizontally
and stably on all four feet.
The max. height adjustment of the feet is 15
mm.
1
4
3
2