Electrolux EWED65HSS - 27" Electric Dryer User manual

Installation Instructions
Electrolux Front-Load Gas & Electric Dryer
Ю Electrolux
13701 8200 A [сас]

2
Finding Information
Please read and save this quide
Thank you for choceing Electrolux, the new premium brand In nome appllances. These instavation
instructions are part of our commitment to customer satisfaction and product quality throughout the Ite
of your new appllanca.
We view your purchase as the beginning of a relationship. To ensure our ability to continue serving you,
please use this page to record Important product Information.
Keep a record for quick reference
Purchase date
Electimolux model number
Electrolux seral number
& NOTE
Registering your product with Electrolux enhances
eur ability to serve you. You can register online at
wwnw.electroluxappliances.com cr by dropping
your Product Registration Card In the mall.
Questions?
For toll-free telephone support In the U.S. and Canada: 1-877-4ELECTROLUX (1-877-435-3287)
For online support and product Information vist nttpizwww.electroluxappllances, com
Table of contents
Finding (POO. ose es easier rra 2
SAFETY —————— a
+ Prednatallatian require to. sr a
Installation recpuiremerita aannam 4-8
* Electrical system requirements.
+ Gas supply recpuirermernta.... ааа
* Exhaust system reguirernerita rennes 5-7
+ Mobile home iratalation. cere 7
+ Cearance requirements. eee eres eres в
* |natalled GIMENO. oe ere a
Electrical ingtallation.................. esses 10-13
+ Grounding requirements - Electric dryer (USA)... 10
ж Grounding requirements - Electric dryer (Canadal... 11
+ Electrical connection - Electric dryer (3-ire cord)... 12
+ Electrical connection - Electric dryer (4-wire cord)... 13
+ Gas pn n — 14
ж Water connection (Steam Model anh)................. 15-18
* General іга айога 17
+ Parfomning installation cycle шаша шаша аншы 18
PREPS QOO —————— 18-23
Bai ———— ns 24
Ubc-aur ——— 24
+ Replacement parte screens 24
n —————————— S5-WX
FANGS S nnn XX
20068 Electrolux Major Appliances All rights reserved.

Important Safety Instructions
Recognize safety symbols, words and
labels
Safety Items throughout this manual are labeled
with a WARNING er CAUTION based on the risk
type as described below:
Ths symbol alerts you to situa-
А WARNING tions that may causa serious body
harm, death or property damage.
The symbol alerts you to situa-
А CAUTION tions that may cause bodily injury
or property damage.
Read all of the following Instructions before
Installing and using this appliance:
+ Destroy the carton and plastic bags after tha dryer
Is unpacked. Children might use tham for play.
Cartons covered with rugs, bedspreads, or plastic
sheets can become artight chambers causing sut-
Tocatlon. Place all materials In a garbage container
or make materials Inaccessibia to children.
+ Clothes dryer Installation апа service must be
performed by a qualified Installer, service agency
or tha gas supplier.
+ Install the clothes dryer according to the manu-
facturers Instructions and local codes.
+ The electrical service to the dryer must conform
with local codes and ordinances and the latest
edition of the National Electrical Code, ANSI
МЕРА 70, or In Canada, the canadian electrical
code 022.1 part 1.
+ The gas service to the dryer must contorm with
local codes and ordinances and the latest adl-
ton of the National Fuel Gas Gode ANSI 2223.1,
Pre-installation requirements
Tools and materials needed for installation:
uu *
rad
©
A SS ‚М
\\
A4
iN
AA
^
3
Adjustable Fhiips. straight, &
plies — square bit screwrkivern
wrenh supplied with
= j^ ovis ог dws
4 nich. rigid metal or
serni-rigid metal exhaust duct work (electria dryer]
Adjustable Unversal wrench Fipe wrench
matching washer
240 volt cord КЕ (10.2 cmi
safety
ar In Canada, GANZACG. B149.1-2000.
+ The dryer Is designed under ANSI Z 21.51 or
ANSLUL 2158 - CAN/CSA C22.2 Mo. 112 (latest
editions) Tor HOME USE only. This dryer Is not
recommended for commercial applications such
as restaurants, beauty salons, etc.
+ Tha Instructions In this manual and all other
Irterature Included with this dryer are not meant
to cover every possible condition and situation
that may occur. Good safe practice and caution
MUST be applied when Installing, operating and
maintaining any appliance.
AS WARNING
For your safety the Information In this manual
must be followed to minimize the risk of Tire
or explosion or to prevent property damage,
personal Injury or loss of Ife. Do not store or use
gasoline or other lammable vapors and Ilquicds In
the vicinity of this or any other appliance.
WHAT TO DO IF YOU SMELL GAS:
+ Do not try to light any appliance.
+ Da not touch any electrical switch; do not use
any phone In your bullding.
+ Clear the room, bullding or area of all occupants.
* Immediately call your gas supplier from a nelgh-
bors phone. Follow the gas suppllar's Instruc-
tions.
+ If you cannot reach your gas supplier, call tha fire
department.
Save these instructions for future
reference.
EAS
x
LU
Жап
|
inm
=
=e
Р
n
=
kt
ә
4
=
EE
LP-resistant
Carpenter's
level
External
for
gas
Hrsad
tape
vent
hood
supply
[far
natural
gas
ER
т
orLP
supply)
гш
nm
М"
МРТ
union
flare
4
in.
gas
lina
adapters
[xz]
and
shuteff
vales
flexible
gas
supply
ine
Metal
fol
tape
clamp
(ges
dryer)
(gas
dryer
(not
duct
tape)

Installation Requirements
Electrical system requirements
= NOTE
Because of potentially Inconsistent voltage capabilities, the use of tnis dryerwith power created
by gas powered generators, solar powered generators, wind pawered generators or any other
generator other than the local utility company Is not recommended.
Electrical requirements for electric dryer:
CIRCUIT - Individual 30 amp. branch reult
fused with 30 amp. time delay fuses or circult
breakers. Use separately fused circuits for
washer and dryer. DO NOT operate a washer
and a dryer on the same circuit.
POWER SUPPLY - 3-wire or 4-wire, 240 volt,
single phase, 60 Hz, Alternating Current.
ЕЛ IMPORTANT
This dryer Is Intermally grounded to neutral unless It
was manufactured for sale In Canada. Grounding
through the neutral link Is prohibited Tor: (1) new
branch circuit Installations, (2) moble homes, (3)
recreational vehicles, and (4) areas where local
codes do not permit grounding through the neutral.
ЗМНЕ POWER SUPPLY GORD KIT (not supplied)
]^ 3-wire receptacle
o> (NEMA type 10-30R)
The dryer MUST employ a 3-conductor power
supply cord NEMA 10-30 type SRDT rated at
240 volt AC minimum, 30 amp, with 3 open
end spade lug connectors with uptumed ends
or closed loop connectors and marked for use
Electrical requirements for gas dryer:
CIRCUIT - Individual, property polartzed and
grounded 15 amp. branch circuit fused with 15
атр. time delay Tuse or circuit breaker.
POWER SUPPLY - 2-wire, with ground, 120 volt,
single phase, 60 Hz, Alternating Current.
POWER SUPPLY CORD - The dryer Is equipped
with a 120 volt 3-wire power cord.
GROUNDING CONNECTION - Sas “Grounding
requirements" In Electrical Installation section.
with clothes dryers. For 3-wire cord connection
Instructions sae ELECTRICAL CONNECTIONS
FOR A S-VIRE SYSTEM.
4-WIRE POWER SUPPLY CORD KIT (not supplied)
, 4wire receptacle
| (NEMA type 14-30R)
The dryer MUST employ a 4-conductor power
supply cord NEMA 14-30 type SRDT or ST (as
required) rated at 240 volt AC minimum, 30 amp,
with 4 open end spade lug connectors with
uplumed ends or closed loop connectors and
marked tor use with clothes dryers. For 4-wire
cord connection Instructions see ELECTRICAL
CONNECTIONS FOR A 4-WIRE SYSTEM.
= NOTE
Dryers manufactured for sale In Canada have
factory-Installed, 4-wire power supply card
(NEMA 14-30R).
OUTLET RECEPTAGLE - NEMA 10-307 or NEMA
14-30R receptacle to be located so the power
supply cord Is accessible when the dryer E In the
Installad position.
GROUNDING CONNECTION - Saa “Grounding
requirements" In Electrical Installation section.

Installation Requirements 5
Gas supply requirements
4 WARNING
EXPLOSION HAZARD
Uncoated copper tubing will corrode when
subjected to natural gas, causing gas leaks.
Use ONLY black Iron, stainless steel, or plastic-
coated brass piping Tor gas supply.
1. Installation MUST conform with local cades, or
Inthe absence of local codes, with the National
Fuel Gas Code, ANSI 2223.1 atest adition).
2. The gas supply line should be 1/2 Inch (1.27
cm) pipa.
3. If codes allow, lib metal tubing may be
used to connect your dryer to the gas supply
line. The tubing MUST be constructed of
stainless steal or plastic-coated brass.
Exhaust system requirements
Use only 4 Inch (10.2 cm) diameter (minimum) гіс
or flexible metal duct and approved vent поса
which has a swing-out dampers) that open when
the dryer Is In operation. When the dryer stops,
the dampers automatically close to prevent drafts
and the entrance of Insects and rodents. To avold
restricting the cutet, malntaln a minimum of 12
Inches (30.5 cm) clearance between the vant hood
and the ground or any other obstruction.
AS WARNING
FIRE HAZARD
Fallure to follow these Instructions can create
excessive drying times and fire hazards.
The following are specific requirements
for proper and safe operation of your
dryer.
A, WARNING
FIRE HAZARD
Do not Install a clothes dryer with Tlexible plastic
or metal Toll venting materials. Flexible venting
matenals are known to collapse, be easily
crushed and trap lint. These conditions will
obstruct clothes dryer alrflav and Increase the
risk of fre.
4. The gas supply line MUST have an Individual
shutoff valve,
5. A 1/8 Inch (0.32 cm) М.РТ. plugged tapping,
accessible Tor test gauge connection, MUST
be Installed Immediately upstream of the gas
supply connection to the dryer.
6. The dryer MUST be disconnected trom the
gas supply piping system during any pressure
testing of the gas supply piping system at test
pressures In excess of 1/2 psig (3.45 КРа).
т. The dryer MUST be isolated from the gas supply
piping system during any pressure testing of the
gas supply piping system at test pressures equal
to or less than 1/2 psig (3.45 KP.
8. Connections Tor the gas aoe comply
for Gas with the Standard for Comec
Appifances, ANSI 221.24.
If your present system Is made up of plastic
duct or metal toll duct, replace It with a rigid or
semi-rigid metal duct. In canada and the United
States If metal (toll type) duct Is Installed, À must
be of a specific type Identified by the appliance
manufacturer as suitable tor use with clothes
dryers and In the United States must also comply
with the Outline for Clothes Dryer Transition Duct,
UL standard 21564. Also, ensure the present duct
Is Tree of any Unt prior to Installing dryer duct.