Electrolux EHT60330 User manual

EHT60330
................................................ .............................................
EN HOB USER MANUAL

Electrolux. Thinking of you.
Share more of our thinking at www.electrolux.com
CONTENTS
Safety information 2
Safety instructions 3
Product description 5
Daily use 5
Helpful hints and tips 7
Care and cleaning 7
Troubleshooting 9
Installation 10
Technical information 13
Environment concerns 14
Subject to change without notice.
SAFETY INFORMATION
Before the installation and use of the appliance, carefully read
the supplied instructions. The manufacturer is not responsible
if an incorrect installation and use causes injuries and dam-
ages. Always keep the instructions with the appliance for fu-
ture reference.
CHILDREN AND VULNERABLE PEOPLE SAFETY
Warning! Risk of suffocation, injury or permanent disability.
• This appliance can be used by children aged from 8 years
and above and persons with reduced physical, sensory or
mental capabilities or lack of experience and knowledge if
they are supervised by an adult or a person who is responsi-
ble for their safety.
• Do not let children play with the appliance.
• Keep all packaging away from children.
• Keep children and pets away from the appliance when it op-
erates or when it cools down. Accessible parts are hot.
• If the appliance has a child safety device, we recommend
that you activate it.
• Cleaning and user maintenance shall not be made by chil-
dren without supervision.
GENERAL SAFETY
• The appliance and its accessible parts become hot during
use. Do not touch the heating elements.
• Do not operate the appliance by means of an external timer
or separate remote-control system.
2 electrolux

• Unattended cooking on a hob with fat or oil can be danger-
ous and may result in fire.
• Never try to extinguish a fire with water, but switch off the
appliance and then cover flame e.g. with a lid or a fire blan-
ket.
• Do not store items on the cooking surfaces.
• Do not use a steam cleaner to clean the appliance.
• Metallic objects such as knives, forks, spoons and lids
should not be placed on the hob surface since they can get
hot.
• If the glass ceramic surface is cracked, switch off the appli-
ance to avoid the possibility of electric shock.
SAFETY INSTRUCTIONS
This appliance is suitable for the following
markets:
FR
INSTALLATION
Warning! Only a qualified person must
install this appliance.
• Remove all the packaging.
• Do not install or use a damaged appli-
ance.
• Obey the installation instruction supplied
with the appliance.
• Keep the minimum distance from the
other appliances and units.
• Always be careful when you move the
appliance because it is heavy. Always
wear safety gloves.
• Seal the cut surfaces with a sealant to
prevent moisture to cause swelling.
• Protect the bottom of the appliance from
steam and moisture.
• Do not install the appliance adjacent to a
door or under a window. This prevents
hot cookware to fall from the appliance
when the door or the window is opened.
• If the appliance is installed above drawers
make sure that the space, between the
bottom of the appliance and the upper
drawer, is sufficient for air circulation.
• The bottom of the appliance can get hot.
We recommend to install a non-combus-
tile separation panel under the appliance
to prevent access to the bottom.
Electrical connection
Warning! Risk of fire and electrical
shock.
• All electrical connections must be made
by a qualified electrician.
• The appliance must be earthed.
• Before carrying out any operation make
sure that the appliance is disconnected
from the power supply.
• Use the correct electricity mains cable.
• Do not let the electricity mains cable tan-
gle.
• Make sure the mains cable or plug (if ap-
plicable) does not touch the hot appli-
ance or hot cookware, when you con-
nect the appliance to the near sockets
• Make sure the appliance is installed cor-
rectly. Loose and incorrect electricity
mains cable or plug (if applicable) can
make the terminal become too hot.
• Make sure that a shock protection is in-
stalled.
• Use the strain relief clamp on cable.
• Make sure not to cause damage to the
mains plug (if applicable) or to the mains
cable. Contact the Service or an electri-
cian to change a damaged mains cable.
electrolux 3

• The electrical installation must have an
isolation device which lets you discon-
nect the appliance from the mains at all
poles. The isolation device must have a
contact opening width of minimum 3
mm.
• Use only correct isolation devices: line
protecting cut-outs, fuses (screw type
fuses removed from the holder), earth
leakage trips and contactors.
Gas connection
• All gas connections should be made by a
qualified person.
• Make sure that there is air circulation
around the appliance.
• The information about the gas supply is
on the rating plate.
• This appliance is not connected to a de-
vice, which evacuates the products of
combustion. Make sure to connect the
appliance according to current installation
regulations. Pay attention to require-
ments regarding adequate ventilation.
USE
Warning! Risk of injury, burns or
electric shock.
• Use this appliance in a household envi-
ronment.
• Do not change the specification of this
appliance.
• Do not use an external timer or a sepa-
rate remote-control system to operate
the appliance.
• Do not let the appliance stay unattended
during operation.
• Do not operate the appliance with wet
hands or when it has contact with water.
• Do not put cutlery or saucepan lids on
the cooking zones. They become hot.
• Set the cooking zone to “off” after use.
• Do not use the appliance as a work sur-
face or as a storage surface.
• If the surface of the appliance is cracked,
disconnect immediately the appliance
from the power supply. This to prevent
an electrical shock.
Warning! Risk of fire or explosion.
• Fats and oil when heated can release
flammable vapours. Keep flames or heat-
ed objects away from fats and oils when
you cook with them.
• The vapours that very hot oil releases can
cause spontaneous combustion.
• Used oil, that can contain food remnants,
can cause fire at a lower temperature
than oil used for the first time.
• Do not put flammable products or items
that are wet with flammable products in,
near or on the appliance.
• Do not try to extinguish a fire with water.
Disconnect the appliance and cover the
flame with a lid or a fire blanket.
Warning! Risk of damage to the
appliance.
• Do not keep hot cookware on the control
panel.
• Do not let cookware to boil dry.
• Be careful not to let objects or cookware
fall on the appliance. The surface can be
damaged.
• Do not activate the cooking zones with
empty cookware or without cookware.
• Do not put aluminium foil on the appli-
ance.
• Cookware made of cast iron, aluminium
or with a damaged bottom can cause
scratches on the glass ceramic. Always
lift these objects up when you have to
move them on the cooking surface.
• Provide good ventilation in the room
where the appliance is installed.
• Make sure that the ventilation openings
are not blocked.
• Use only stable cookware with the cor-
rect shape and diameter larger than the
dimensions of the burners. There is a risk
of overheating and rupture of the glass
plate (if applicable).
• Make sure the flame does not go out
when you quickly turn the knob from the
maximum to the minimum position.
• Make sure pots are centrally positioned
on the rings and do not stick out over
edges of the cooking surface.
• Use only the accessories supplied with
the appliance.
• Do not install a flame diffuser on the
burner.
4 electrolux

CARE AND CLEANING
Warning! Risk of damage to the
appliance.
• Clean regularly the appliance to prevent
the deterioration of the surface material.
• Do not use water spray and steam to
clean the appliance.
• Do not clean the burners in the dish-
washer.
• Clean the appliance with a moist soft
cloth. Only use neutral detergents. Do
not use abrasive products, abrasive
cleaning pads, solvents or metal objects.
DISPOSAL
Warning! Risk of injury or suffocation.
• Contact your municipal authority for infor-
mation on how to discard the appliance
correctly.
• Disconnect the appliance from the mains
supply.
• Cut off the mains cable and discard it.
• Flat the external gas pipes.
PRODUCT DESCRIPTION
145 mm
1
6 5
2 3
4
1Electric cooking zone 1500 W
2Semi-rapid burner
3Power indicator
4Control knobs
5Auxiliary burner
6Rapid burner
CONTROL KNOBS
Symbol Description
no gas supply / off
position
ignition position /
maximum gas supply
minimum gas supply
ELECTRIC COOKING ZONES
CONTROL KNOBS
Symbol Function
0off position
1minimum heat
6maximum heat
DAILY USE
Warning! Refer to "Safety information"
chapter.
IGNITION OF THE BURNER
Warning! Be very careful when you
use open fire in kitchen environment.
electrolux 5

Manufacturer decline any responsibility
in case misuse of the flame
Always light the burner before you put
cookware.
To light the burner:
1. Turn the control knob counterclockwise
to the maximum position ( ) and
push it down.
2. Keep the control knob pushed for ap-
proximately 5 seconds; this will let ther-
mocouple to warm up. If not, the gas
supply will be interrupted.
3. Adjust the flame after it is regular.
If after some tries the burner does not
light, check if the crown and its cap are
in correct positions.
A
B
C
D
A) Burner cap
B) Burner crown
C) Ignition candle
D) Thermocouple
Warning! Do not keep the control
knob pushed for more than 15
seconds.
If the burner does not light after 15
seconds, release the control knob, turn
it into off position and try to light the
burner again after minimum 1 minute.
Important! In the absence of electricity you
can ignite the burner without electrical
device; in this case approach the burner
with a flame, push the relevant knob down
and turn it counter-clockwise to maximum
gas release position.
If the burner accidentally goes out, turn
the control knob to the off position and
try to light the burner again after mini-
mum 1 minute.
The spark generator can start automat-
ically when you switch on the mains,
after installation or a power cut. It is
normal.
TURNING THE BURNER OFF
To put the flame out, turn the knob to the
symbol .
Warning! Always turn the flame down
or switch it off before you remove the
pans from the burner.
OPERATING ELECTRIC ZONES
To switch on and increase the heat setting
turn the knob counterclockwise. To de-
crease the heat setting turn the knob clock-
wise. To switch off turn the knob to the 0.
Power indicator is activated when electric
cooking zone is turned on, and will stay on
until electric cooking zone is switched off.
BEFORE, FIRST USE
Set the maximum position and operate the
appliance for 10 minutes. This is to burn off
the residue in the appliance. After that, op-
erate the appliance at minimum position for
20 minutes. During this period, an odour
and smoke can occur. This is normal. Make
sure that the airflow is sufficient.
After this operation, clean the appliance
with a soft cloth soaked in warm water.
EXAMPLES OF COOKING
APPLICATIONS
Heat
set-
ting:
Use to:
1Keeping warm
2Gentle simmering
3Simmering
4Frying / browning
5Bringing to the boil
6Bringing to the boil / quick frying /
deep-frying
RAPID HOT PLATE
A red dot in the middle of the plate shows a
rapid hot plate. A rapid hot plate heats up
faster than usual plates.
6 electrolux

The red dot is painted on the surface and
can come off after some time. It does not
have an effect on the performance of the
appliance.
The rapid hot plate can smoke and make
an odour when you use it for the first time.
The smoke and an odour will go off after a
while.
The rapid hot plate can smoke and make
an odour when you use it for the first time.
The smoke and an odour will go off after a
while.
HELPFUL HINTS AND TIPS
Warning! Refer to "Safety information"
chapter.
ENERGY SAVING
• If possible, always put the lids on the
cookware.
• Put cookware on a solid hotplate be-
fore you start it.
• Stop the solid hotplate before the
end of the cooking time to use resid-
ual heat.
• For satisfactory results, the diameter
of pans and cooking zones must
have the same dimensions.
• When the liquid starts to boil, turn down
the flame to barely simmer the liquid.
Use cookware with diameters applicable to
the size of burners.
Burner Diameters of cookware
Rapid 160 - 260 mm
Semi-rapid 120 - 220 mm
Auxiliary 80 - 180 mm
Warning! Do not use cast iron pans,
potstones, grill or toaster plates on gas
burners.
Warning! Do not put the same pan on
two burners.
Warning! Make sure pot handles do
not protrude over the front edge of the
cooktop and that pots are centrally
positioned on the rings in order to
achieve maximum stability and to
obtain lower gas consumption.
Do not place unstable or deformed pots on
the rings to prevent from spill and injury.
Warning! Liquids spilt during cooking
can cause the glass to break
Information on acrylamides
Important! According to the newest
scientific knowledge, if you brown food
(specially the one which contains starch),
acrylamides can pose a health risk. Thus,
we recommend that you cook at the lowest
temperatures and do not brown food too
much.
CARE AND CLEANING
Warning! Refer to "Safety information"
chapter.
Warning! Deactivate the appliance and
let it cool down before you clean it.
Disconnect the appliance from the
electrical supply before you do cleaning
or maintenance work.
Scratches or dark stains on the surface
have no effect on how the appliance
operates.
• You can remove the pan supports to
easily clean the hob.
• To clean the enamelled parts, cap and
crown, wash them with warm soapy wa-
ter and dry them carefully before you put
them back.
• Wash stainless steel parts with water,
and then dry them with a soft cloth.
• The pan supports are not dishwasher
proof. They must be washed by hand.
electrolux 7

• When you wash the pan supports by
hand, take care when you dry them as
the enamelling process occasionally
leaves rough edges. If necessary, remove
stubborn stains using a paste cleaner.
• Make sure you position the pan supports
correctly after cleaning.
• To make the burners work correctly,
make sure that the arms of the pan sup-
ports are in the centre of the burner.
•Be very careful when you replace the
pan supports to prevent the hob top
from damage.
After cleaning, dry the appliance with a soft
cloth.
Removing the dirt:
1. – Remove immediately: melting plas-
tic, plastic foil, and food containing
sugar.
–Stop the appliance and let it cool
down before you clean: limescale
rings, water rings, fat stains, shiny
metallic discolorations. Use a special
cleaner applicable for surface of hob.
2. Clean the appliance with a damp cloth
and some detergent.
3. At the end rub the appliance dry
with a clean cloth.
Warning! Do not use knives, scrapers
or similar instruments to clean the
surface of the glass or between the
rims of the burners and the frame (if
applicable).
Warning! Do not slide cookware over
the glass because it could scratch the
surface. Also, do not let hard or sharp
objects fall onto the glass or hit the
edge of the hob.
CLEANING THE ELECTRIC HOTPLATE
Clean the appliance after each use.
Always use cookware with clean bottom.
Warning! Before any maintenance or
cleaning can be carried out, you must
disconnect the hob from the electricity
supply.
The hob is best cleaned while it is still
warm, as spillage can be removed
more easily than if it is left to cool.
Scratches or dark stains have no effect
on how the appliance operates.
Removing the dirt:
1. Use the fine scouring powder or a
scouring pad to remove the dirt.
2. Clean the appliance with a damp cloth
and some detergent.
3. Heat the hotplate to a low temperature
and leave to dry.
4. To maintain the hotplates, wipe the
plates with a drop of olive oil on a kitch-
en towel to prevent rust.
Important! For stainless steel edges of the
hob use cleaner for stainless steel.
The stainless steel edge of the plate
can be slightly discoloured as a result
of the thermal load.
CLEANING OF THE SPARK PLUG
This feature is obtained through a ceramic
ignition candle with a metal electrode. Keep
these components well clean to prevent dif-
ficult lighting and check that the burner
crown holes are not obstructed.
PERIODIC MAINTENANCE
Periodically speak your local Service Force
Centre to check the conditions of the gas
supply pipe and the pressure adjuster, if fit-
ted.
8 electrolux

TROUBLESHOOTING
Problem Possible cause Remedy
There is no spark when lighting
the gas.
• There is no electrical supply. • Make sure that the appliance
is connected and the electri-
cal supply is switched on.
• Do a check of the fuse. If the
fuse is released more than
one time, refer to a qualified
electrician.
There is no spark when lighting
the gas.
• The burner cap and crown
are placed unevenly.
• Make sure that the burner
cap and crown are in the
correct positions.
The flame is blown out immedi-
ately after ignition.
• The thermocouple is not
heated sufficiently.
• After lightning the flame,
keep the knob pushed for
approximately 5 seconds.
The gas ring burns unevenly. • The burner crown is blocked
with food residue.
• Make sure that the injector is
not blocked and the burner
crown is clear of food parti-
cles.
The appliance does not oper-
ate.
• There is no electrical supply. • Make sure that the appliance
is connected and the electri-
cal supply is switched on.
• Do a check of the fuse. If the
fuse is released more than
one time, refer to a qualified
electrician.
The electrical cooking zone
does not heat up.
• There is no electrical supply.
• The wrong knob is used to
operate the cooking zone.
• Make sure that the appliance
is connected and the electri-
cal supply is switched on.
• Make sure that you turn the
correct control knob.
• Do a check of the fuse. If the
fuse is released more than
one time, refer to a qualified
electrician.
The effectiveness of the hob is
not satisfactory.
• The hob is not clean.
• The cookware is not correct.
• Make sure that the hob is
clean and dry.
• Make sure that the cookware
is the correct size for the
cooking zone.
• Make sure that the cookware
has a flat bottom.
• Make sure that the heat set-
ting is correct for this type of
cooking.
If there is a fault, first try to find a solution to
the problem yourself. If you cannot find a
solution to the problem yourself, speak your
dealer or the local Service Force Centre.
If you operated the appliance incorrect-
ly, or the installation was not carried
out by a registered engineer, the visit
from the customer service technician or
dealer may not take place free of
charge, even during the warranty peri-
od.
electrolux 9

These data are necessary to help you
quickly and correctly. These data are
available on the supplied rating plate.
• Model description .................
• Product number (PNC) .................
• Serial Number (S.N.) .................
Use the original spare parts only. They are
available at Service Force Centre and ap-
proved spare parts shops.
LABELS SUPPLIED WITH THE
ACCESSORIES BAG
Stick the adhesive labels as indicated be-
low:
MOD.
PROD.NO.
SER.NO
DATA
MOD.
PROD.NO.
SER.NO
DATA
MODELMODEL
MOD.
PROD.NO.
SER.NO.
03 IT
MADE IN ITALY
TYPE
230V-50Hz
IP20
0049
1 2 3
1Stick it on Guarantee Card and send
this part
2Stick it on Guarantee Card and keep
this part
3Stick it on instruction booklet
INSTALLATION
Warning! Refer to "Safety information"
chapter.
Warning! The following instructions
about installation, connection and
maintenance must be carried out by
qualified personnel in compliance with
standards and local regulations in
force.
GAS CONNECTION
Choose fixed connections or use a flexible
pipe in stainless steel in compliance with
the regulation in force. If you use flexible
metallic pipes, be careful they do not come
in touch with mobile parts or they are not
squeezed. Also be careful when the hob is
put together with an oven.
Important! Make sure that the gas supply
pressure of the appliance obeys the
recommended values. The adjustable
connection is fixed to the comprehensive
ramp by means of a threaded nut G 1/2".
Screw the parts without force, adjust the
connection in the necessary direction and
tighten everything.
10 electrolux

ABC
A) End of shaft with nut
B) Washer
C) Elbow
Rigid connection:
Carry out connection by using metal rigid
pipes (copper with mechanical end).
"Flexible" connection with mechanical
end:
–Natural gas: connection carry out with a
flexible pipe with mechanical end which is
screwed directly on the elbow finishing
the slope of the appliance.
–Butane / Propane: use a flexible tube,
equipped with it's collars if it is worth vis-
iting over all it's length and if the appli-
ance runs only on butane. If the appli-
ance runs on Propane, use a flexible pipe
with suitable metal end.
Flexible nonmetal pipes connection:
If it is possible to easily control the connec-
tion in its full area, you can use a flexible
pipe. Tightly attach the flexible pipe by
clamps.
Liquid gas: use the rubber pipe holder. Al-
ways engage the gasket. Then continue
with the gas connection. The flexible pipe is
prepared for apply when:
– it can not get hot more than room tem-
perature, higher than 30°C;
– it is no longer than 1500 mm;
– it shows no throttles;
– it is not subject to traction or torsion;
– it does not get in touch with cutting
edges or corners;
– it can be easily examined in order to
check its condition.
The control of preservation of the flexible
pipe consists in checking that:
– it does not show cracks, cuts, marks of
burnings on the two ends and on its full
length;
– the material is not hardened, but shows
its correct elasticity;
– the fastening clamps are not rusted;
– expired term is not due.
If one or more defects are visible, do not re-
pair the pipe, but replace it.
Important! When installation is complete,
make sure that the seal of each pipe fitting
is correct. Use a soapy solution, not a
flame!
INJECTORS REPLACEMENT
1. Remove the pan supports.
2. Remove the caps and crowns of the
burner.
3. With a socket spanner 7 remove the in-
jectors and replace them with the ones
which are necessary for the type of gas
you use (see table in "Technical Data"
chapter).
4. Assemble the parts, follow the same
procedure backwards.
5. Replace the rating plate (it is near the
gas supply pipe) with the one for the
new type of gas supply. You can find
this plate in the package supplied with
the appliance.
If the supply gas pressure is changeable or
different from the necessary pressure, you
must fit an applicable pressure adjuster on
the gas supply pipe.
ADJUSTMENT OF MINIMUM LEVEL
To adjust the minimum level of the burners:
1. Light the burner.
2. Turn the knob on the minimum posi-
tion.
3. Remove the knob.
4. With a thin screwdriver, adjust the by-
pass screw position.
electrolux 11

A
A) The by-pass screw
• If you change from natural gas G20/G25
20/25 mbar to liquid gas, fully tighten the
by-pass screw in.
• If you change from liquid gas to natural
gas G20/G25 20/25 mbar, undo the by-
pass screw approximately 1/4 of a turn.
• If you change from natural gas G20/G25
20/25 mbar to town gas G130 8 mbar,
unscrew approximately 3/4 of a turn.
• If you change from town gas G130 8
mbar to natural gas G20/G25 20/25
mbar screw approximately 3/4 of a turn.
• If you change from liquid gas to town gas
G130 8 mbar unscrew approximately 1
turn.
Warning! Make sure the flame does
not go out when you quickly turn the
knob from the maximum position to the
minimum position.
ELECTRICAL CONNECTION
• Ground the appliance according to safety
precautions.
• Make sure that the rated voltage and
type of power on the rating plate agree
with the voltage and the power of the lo-
cal power supply.
• This appliance is supplied with a mains
cable. It has to be supplied with a correct
plug, able to support the load marked on
the rating plate. The plug has to be fitted
in a correct socket.
• Any electrical component must be instal-
led or replaced by the Service Force
Centre technician or qualified service per-
sonnel.
• Always use a correctly installed shock-
proof socket.
• Make sure that there is an access to the
mains plug after installation.
• Do not pull the mains cable to disconnect
the appliance. Always pull the mains
plug.
• The appliance must not be connected
with an extension cable, an adapter or a
multiple connection (risk of fire). Check
that the ground connection is in conform-
ity with the standard and regulations
force.
• The power cable must be placed in such
a way that it does not touch any hot part.
• Connect the appliance to the mains with
a device that lets to disconnect the appli-
ance from the mains at all poles with a
contact opening width of minimum 3
mm, eg. automatic line protecting cut-
out, earth leakage trips or fuse.
• None of a parts of the connection cable
can not get a temperature 90 °C. The
blue neutral cable must be connected to
the terminal block label with "N". The
brown (or black) phase cable (fitted in the
terminal block contact marked with "L")
must always be connected to the live
phase.
REPLACEMENT OF THE CONNECTION
CABLE
To replace the connection cable use only
H05V2V2-F T90 or equivalent type. Make
sure that the cable section is applicable to
the voltage and the working temperature.
The yellow/green earth wire must be ap-
proximately 2 cm longer than the brown (or
black) phase wire.
BUILDING IN
min.
55 mm
min.
650 mm
550 mm
470 mm
min.
450 mm
30 mm
12 electrolux

B
A
A) supplied seal
B) supplied brackets
POSSIBILITIES FOR INSERTION
Kitchen unit with door
The panel installed below the hob must be
easy to remove and let an easy access in
case a technical assistance intervention is
necessary.
min 20 mm
(max 150 mm)
30 mm
60 mm
B
A
A) Removable panel
B) Space for connections
Kitchen unit with oven
The hob recess dimensions must obey the
indication and the kitchen unit must be
equipped with vents to let a continuous
supply of air. The electrical connection of
the hob and the oven must be installed
separately for safety reasons and to let easy
remove oven from the unit.
50 cm2
360 cm2 180 cm2
120 cm2
TECHNICAL INFORMATION
Hob dimensions
Width: 580 mm
Length: 510 mm
Hob recess dimensions
Width: 550 mm
Length: 470 mm
Heat input
Rapid burner: 2,9 kW
Semi-rapid burner: 1,9 kW
Auxiliary burner: 1,0 kW
Electric zone: 1,5 kW
TOTAL GAS POWER: G20/G25 (2E+) 20/25 mbar = 5,8 kW
G30 (3+) 28-30 mbar = 407 g/h|
G31 (3+) 37 mbar =400 g/h|
G130 (1c) 8 mbar = 5,8 kW
TOTAL ELECTRIC POWER: 1,5 kW
electrolux 13

Electric supply: 230 V ~ 50 Hz
Category: III1c2E+3+
Gas connection: G 1/2"
Gas supply: G20/G25 (2E+) 20/25 mbar
Appliance class: 3
By-pass diameters
Burner Ø By-pass in 1/100
mm
Burner Ø By-pass in 1/100
mm
Auxiliary 28 Rapid 42
Semi-rapid 32
Gas burners
BURN
ER
NOR-
MAL
POW-
ER
RE-
DUC-
ED
POW-
ER
NORMAL POWER
NATURAL GAS
G20/G25 (2E+) 20/25
mbar
LPG
(Butane/Propane) G30/
G31 (3+) 28-30/37
mbar
LPG
(Town Gas)
G130 (1c) 8
mbar
inj.
1/100
mm
G20
20
mbar
G25
25
mbar
inj.
1/100
mm
G30
28–30
mbar
G31
37
mbar
inj.
1/100
mm
m³/h
m³/h m³/h g/h g/h
Auxili-
ary 1,0 0,33 70 0,095 0,111 50 73 71 127 0,140
Semi-
rapid 1,9 0,45 96 0,181 0,210 71 138 136 195 0,266
Rapid
2,9
(natu-
ral
gas)
2,7
(LPG)
0,75 119 0,276 0,321 86 196 193 240 0,406
ENVIRONMENT CONCERNS
The symbol on the product or on its
packaging indicates that this product may
not be treated as household waste. Instead
it should be taken to the appropriate
collection point for the recycling of electrical
and electronic equipment. By ensuring this
product is disposed of correctly, you will
help prevent potential negative
consequences for the environment and
human health, which could otherwise be
caused by inappropriate waste handling of
this product. For more detailed information
about recycling of this product, please
contact your local council, your household
waste disposal service or the shop where
you purchased the product.
PACKAGING MATERIAL
The packaging materials are friendly to
the environment and can be recycled.
The plastic components are identified
by marking: >PE<,>PS<, etc. Discard
the packaging materials as household
waste at the waste disposal facilities in
your municipality.
14 electrolux

electrolux 15

www.electrolux.com/shop 892953143-A-FR-242012