Electrolux EKG61107OX User manual

14. INSTALLATION
WARNING!
Refer to Safety chapters.
14.1 Location of the appliance
You can install your freestanding
appliance with cabinets on one or two
sides and in the corner.
Keep a distance of about 1
cm between the appliance
and the back wall to make
sure that the lid opens.
For minimal distances for fitting check
the table.
A
C
D
D
B
Minimum distances
Dimension mm
A400
B650
C150

Dimension mm
D20
14.2 Technical data
Voltage 220 - 240 V
Frequency 50 / 60 Hz
Appliance class 1
Dimension mm
Height 855
Width 600
Depth 600
14.3 Other technical data
Appliance category: I3B/P
Gas original: G30 30 mbar
14.4 Bypass diameters
BURNER Ø BYPASS1) 1/100 mm
Auxiliary 29 / 30
Semi-rapid 32
Triple Crown 67
Oven 44
1) Type of bypass depends on model.
14.5 Gas burners for LPG G30 30 mbar
BURNER NORMAL
POWER kW
REDUCED
POWER kW
INJECTOR
MARK 1/100
mm
NOMINAL GAS
FLOW g/h
Triple Crown 4.0 1.80 101 291
Semi-rapid 2.0 0.43 71 145
Auxiliary 1.0 0.35 50 73
Oven 2.7 0.90 80 196
Grill 1.9 - 71 138
14.6 Gas connection
Use a fixed connections or use a flexible
stainless steel pipes in compliance with
the regulation in force. If you use flexible
metallic pipes, make sure they do not
come in touch with mobile parts and they
are not squeezed.

WARNING!
The gas connection pipe
must not touch the part of
the appliance shown in the
illustration.
14.7 Flexible nonmetal pipes
connection
If you have an easy access to the
connection, you can use a flexible pipe.
The flexible pipe must be tightly attached
by clamps.
In installation always use the pipe holder
and the gasket. The flexible pipe can be
applied when:
• it can not get hotter than room
temperature, higher than 30 °C,
• it is not longer than 1500 mm,
• it has no narrowing anywhere,
• it is not twisted or tighten,
• it does not get in touch with sharp
edges or corners,
• it's conditions can be easily checked.
When checking the flexible pipe make
sure:
•it does not show cracks, cuts, marks
of burnings on the two ends and on its
full length,
• the material is not hardened, but
shows its correct elasticity,
• the fastening clamps are not rusted,
• expired term is not due.
If one or more defects are visible, do not
repair the pipe, but replace it.
WARNING!
When installation is
complete, make sure that
the seal of each pipe fitting
does not leak. To check the
seal use a soap solution, not
a flame.
The gas supply ramp is on the rear side
of the control panel.
WARNING!
Before you connect the gas,
disconnect the appliance
from the electricity supply or
switch off the fuse in the
fuse box. Close the primary
valve of the gas supply.
14.8 Connection to gas supply
A
B
D
C
A. Gas connection point (only one point
is applicable for the appliance)
B. Gasket
C. Adjustable connection
D. LPG pipe holder
14.9 Levelling of the appliance
Use small feet on the bottom of
appliance to set the appliance top
surface level with other surfaces.
14.10 Anti-tilt protection
Set the correct height and area for the
appliance before you attach the anti-tilt
protection.
CAUTION!
Make sure you install the
anti-tilt protection at the
correct height.
www.electrolux.com24

Make sure that the surface
behind the appliance is
smooth.
You must install the anti-tilt protection. If
you do not install it, the appliance can tilt.
Your appliance has the symbol shown on
the picture (if applicable) to remind you
about the installation of the anti-tilt
protection.
1. Install the anti-tilt protection 232 -
237 mm down from the top surface of
the appliance and 110 - 115 mm from
the side of the appliance into the
circular hole on a bracket. Screw it
into the solid material or use
applicable reinforcement (wall).
110-115
mm
232- 237
mm
2. You can find the hole on the left side
at the back of the appliance. Lift the
front of the appliance and put it in the
middle of the space between the
cupboards. If the space between the
bench cupboards is larger than the
width of the appliance, you must
adjust the side measurement to
centre the appliance.
If you changed the
dimensions of the cooker,
you must align the non-tip
device correctly.
CAUTION!
If the space between the
bench cupboards is larger
than the width of the
appliance, you must adjust
the side measurement to the
centre of the appliance.
14.11 Electrical installation
WARNING!
The manufacturer is not
responsible if you do not
follow the safety precautions
from Safety chapters.
This appliance is supplied with a main
plug and a main cable.
WARNING!
The power cable must not
touch the part of the
appliance shown in the
illustration.