Electrolux TWINSTREAM User manual

Ne
~ TWINSTREAM
[
WET
&
DRY_|

1 Shampoo tank 8 Suction inlet
2 Aijr tube fixing 9 Drum for dust and
3 Shampoo tube quick - dirty water
release valve 10 Airinjection outlets |
4 On/off switch 11 Two position lever
5 Carrying handle 12 Exhaustfilter
6 Power unit 13. Removabie grille 7
7 Float 14 Location lug

Ist filter
cloth
2nd filter
paper
14

1)
2)
3)
4)
5)
6)
7)
8)
9)
10)
11)
12)
13)
14)
15)
16)
17)
18)
Rte,
Flexible
hose
with
handle
and
suction
control
Shampoo tank
Straight tubes
Crevice nozzle
Nozzle for upholstery and wet pickup
Dusting brush
Carpet/hard floor nozzle
Trigger control
Shampoo nozzle
Hard floor adaptor
Air and shampoo tubing
Paper dustbag
Cloth filter
Paper filter
Vanish shampoo
Castor wheels
Fixing rings for shampoo and air
tubing
Filter fixing band
~
How to fit the 5 castor wheels to the
drum:
Overturn the drum on the floor and
insert the stem of the castors in the 5
holes on the underside. Apply
oressure
until
the
ster
is
fully
inserted.
Check that all stems are inserted up
to
the
end
of
the
black
plastic
cover
and that all are level (Fig. 16).

IMPORTANT USER INFORMATION
| It is most important that this instruction book should be retained with the
| appliance for future reference. Should the appliance be sold or transferred
to another owner, or should you move house and leave the appliance,
always ensure that the book is supplied with the appliance in order that the
new owner can be acquainted with the functioning of the appliance and
the relevant warnings. These warnings are provided in the interest of safety.
You must read them carfully before installing or using the appliance.
e This appliance is designed to be operated by adults. Children should not
be allowed to tamper with the controls or play with the product.
e jit is dangerous to alter the specifications or modify the product in any
way.
¢ Donotuse the appliance in the presence of flammable gases.
| e Never leave the appliance running unattended.
e Remove the plug from the wall socket before attempting any form of user
maintenance specified in the user instruction booklet.
¢ Donot carry or drag the vacuum cleaner by mains supply cable.
- ¢ Do not tug at the mains supply cable to remove the plug from the wall
socket.
e Keep the mains supply cable away from heat, oil, snaro edges and rough
surfaces.
e Always ensure that the cable is not damaged in any way.
° Never pick up hot cinders or lighted cigarette ends.
e Extreme care is required when cleaning stair carpets with your appliance.
Ensure that your cleaner is in a stable position at the bottom of the stairs,
and take care not to stretch the hose beyond its actual length. Always
| ensure when using your cleaner on the stair treads that you keep one
| hand firmly on the appliance.
e Dust bags and filters should be canged at regular intervals as stated in
your instruction booklet.
¢ Do not use the appliance for wet vacuuming with the foam motor filter
|
removed.
|
e Do not use the appliance for dry vacuuming with the foam and paper
filters removed.
_@ When fitting and changing the accessories always follow the instructions
| in the user instruction booklet. |
| e Under no circumstances should you attempt to repair the appliance
ae yourself.
Repairs undertaken by unauthorised or inexperienced persons may Cause
injury and/éPserious malfunctioning.
a | e This appliance should be serviced by authorised Electrolux personnel and
. ' only genuine Electrolux spare parts should be used.
e Always remove liquids from the container after use.
| e Some proprietory carpet conditioning powders contain substances which
| if left in the vacuum cleaner for extended periods may damage the
plastic parts of the cleaner. Please check the manufacturers instructions
of these powders before use.
|e Extreme care is required when carpet/upholstery shampooing near wall
sockets.
Do not spray towards a socket or any electrical appliance.
e When using the machine for wet pick-up ensure that the correct |
accessories are used as stated in your instruction book,

AL INFORMATION
Read
the
information
contained
in
this
booklet
carefully,
as
if
provides
important
instructions
on
safe
installation,
use
and
maintenance.
Keep
this
booklet
in
a
safe
place
for
further
reference.
After
removing
the
packaging,
check
that
the
appliance
is
undamaged.
If
in
doubt,
do
not
use
the
appliance.
Consult
qualified
service
personell.
The
packaging
(plastic
bags,
expanded
polystyrene,
nails,
etc...)
should
be
kept
out
of
the
reach
of
children
as
it
is
potentially
dangerous.
Before
connecting
the
appliance
to
the
power
supply,
make
sure
that
the
information
on
the
identification
plate
corresponds
to
that
of
the
power
supply
rating.
If
the
power
socket
and
plug
of
the
appliance
are
incompatible,
have
the
plug
been
replaced
by
one
of
a
suitable
type
by
a
qualified
technician,
who
should
also
ensure
that
the
cable
section
of
the
plug
is
suitable
for
the
absorbed
power
of
the
appliance.
Generally
avoid
the
use
of
adapters,
multiple
plugs
and/or
extension
cables.
Do
not
leave
the
appliance
exposed
to
atmospheric
agents
such
as
rain,
sun,
etc.
Do
not
allow
children
to
use
the
appliance
without
supervision.
Do
not
leave
the
appliance
plugged
in
when
not
in
use.
Remove
the
plug
from
the
power
supply
socket
when
the
appliance
is
not
being
used.
Before
carrying
out
any
cleaning
or
maintenance
operations,
remove
the
plug
from
the
wall
socket.
In
the
event
of
malfunction
or
incorrect
performance,
switch
off
the
appliance
and
do
not
tamper
with
it.
For
repairs,
consult
only
a
service
centre
authorised
by
the
manufacturer
and
insist
on
the
use
of
genuine
spare
parts.
If
these
rules
are
not
observed,
the
safety
of
the
appliance
cannot
be
guaranteed.
—

CONNECTING TO YOUR ELECTRICITY SUPPLY
Permanently connected to the cleaner is a mains supply (2-core) cable.
The mains supply cable is fitted with a non-rewireable plug incorporating a
13A fuse. In the event of the fuse requiring replacement the fuse cover
should be removed using a small screwdriver. The old MUST be replaced by
a 13A ASTA approved BS 1362 fuse and the cover must be replaced before
the plug is used again. In the event of loss of the fuse cover, replacements
can be obtained from your dealer or Electricity Board and must be of the
same colour as indicated by the coloured insert on the base of the plug.
If difficulty is experienced in obtaining a replacement, contact your nearest
Service Centre. (Please see the separate Service Organisation leaflet). In no
circumstances must the plug be used without a correct fuse cover fitted.
In the event that the non-rewireable plug is unsuitable for the type of
sockets in your home, it should be cut off and disposed of safely or
destroyed to avoid any possible shock hazard resulting from the plug being
inserted into a 13A socket elsewhere.
A suitable replacement plug should be fitted as follows:
IMPORTANT
In using a three-pin plug, do not
make any connection to the
terminal marked with the letter E or
by the earth symbol or coloured
green or green-and-yellow. This
cleaner is double insulated and no
earth connection is necessary.
lf a 13-amp fused plug is used, it
MUST be fitted with a 13-amp fuse. it
is in your interest to ensure that the
plug. is correctly attached to the
mains cable. In case of doubt, have
it done by a qualified electrician, as
the Company cannot regard the
repair of faults on the plug
connection as a service that can be
given free of charge under the terms
of the guarantee
CORD CLAMP
gre

USING THE TWINSTREAM AS
A DRY VACUUM CLEANER
1) Remove the shampoo tank from
the power unit by faking hold of
it from the rear and lifting it off
(see fig. 3).
IMPORTANT
2) Ensure the two. air injection
outlets are closed by moving the
lever from right to left to close
(see fig. 4).
3) Remove the motor housing from
the drum by releasing the clips in
an outward direction (see fig. 5)
DRY FILTERING SYSTEMS
Check that all the dry suction filters
are correctly fitted as shown in fig.
14,
1) Ensure location lug is lined up
with recess on the rear of drum
and replace the power unit onto
the drum and secure the latches.
2) Insert the end of the hose into.
the suction inlet and turn if to the
left until is locked in place
3) Insert the straight tubes onto the
hose handle.
4) Insert the appropriate nozzie
onto the end of the, straight
Tubes.
The appliance can be used with or
without a dustbag, but it is
recommended that a dustbag is
used. See dustbag for fitting
instructions.
Note: This appliance is fitted with a
handle with suction regulator
to vary the suction power. The
variation is carried out by
means of the pushbutton on
the handle. When the hole is
closed maximum suction is
obtained, and the suction
power is gradually reduced as
this ls opened.
PICKING UP WET SPILLAGES
Release the latches by pushing them
outwards from the top, and raise the
power unit.
Remove the paper and cloth filters
from the basket and keep safely,
check that the round foam motor
fitter under the float is correctly fitted
and perfectly clean. See fig. 6 and
6a.
Replace the power unit onto the
drum and push the latches back into
position.
Attach the hose in position
Position the weft suction nozzle on the
straight tubes.
USING THE TWINSTREAM
FOR SHAMPOOING
CARPETS
Before washing thoroughly vacuum
the carpet.
Empty the dust from the drum and
wash it with water.
Remove the paper and cloth filter,
Check that the foam motor filter
under the float is not obstructed or
dirty.
Note: The shampoo solution should
only be used as directed. An
unobtrusive section of the
carpet shoula Uc cnecked for
colour fastness prior use.
Attach the trigger control onto the
bent end of the main hose in
direction of arrow (Fig. 7) making
sure it clicks into place.
Assemble the hose, straight tubes
and shampoo nozzie, clip the
combined shampoo and air tube
onto the hose and straight tubes with”
the fixing rings, the rings should be
placed at regular intervals in the
a

preformed slots on the shampoo
air/tubing (Fig. 8)
4) Tne shampoo tank holds a
maximum of 3.2 litres G litres of
water and 200 mi of shampoo).
When using shampoo mix with
warm tap water.
IMPORTANT:
In order for the Twinstream to
work effectively the fwo. Air
Injection outlets must be open.
Slide the lever from left fo right as
per figure 9. Place the shampoo
tank on the power unit and click
into place.
5 Insert the two ends of the
shampoo and air tube into the
connectors at the front of the
shampoo tank.
Tubing with metal valve fits into the
metal connector.
Tubing with black plastic valve fits
into larger diameter hole (Fig. 10).
Note: When cleaning hard floors
place the adaptor onfo the
nozzle (see fig. 12).
USING THE APPLIANCE TO
SHAMPOO
Press the on/off switch on the upper
part of the appliance to start the
motor.
Position the nozzle in working position
on the floor, pull the trigger and wait
for a few seconds until the shampoo
starts to spray from the nozzle.
Start to clean the surface from the
point furthest from the entrance door
of the room.
Draw the nozzle slowly towards
yourself, pressing the trigger and
gently holding the nozzie against the
carpet (see Fig. 17 e 12).
Release the trigger and go over the
cleaned area several times to dry.
Continue the cleaning operation
parallel to the area already
cleaned, with a slight overlap to
ensure that no part of the surface is
left untreated.
To remove the shampoo tubing press
the button on the top of the
connector until the tubing pops out
(see fig. 11).
To remove the air tubing, turn
anti-clockwise and pull out.
Remove shampoo tank.
Before storing the appliance rinse
out the shampoo tank and dirty
water drum.
Always ensure that the — dirty
water/dust tank is dry before
replacing the dustbag and dry filters.
Cable storage
After use the cable can be wound
around the storage area beneath
the power unit (Fig. 13).
FILTER CLEANING (Fig. 14)
IMPORTANT
It is essential fo keep all filters clean
and unclogged.
For efficent performance all filters
should be checked for blockages
regularly in the following way.
Paper filfer
Keep a small stock of these and fit a
new one when the old one
becomes clogged.
Cloth filter
Brush the filter, wash if with soapy
water, then dry if completely and
return if to its housing.
Round foam motor filter (Fig. 6 and
6a).
This is housed inside the basket.
Check regularly. To clean remove
the basket by twisting and gently
pulling it away from the power unit.
Wash the filter in warm water and
dry thoroughly. Repiace it in the slots
“‘é

provided.
Ensure
that
the
white
ball
valve
is
in
the
basket.
Replace
the
basket
by
aligning
the
recess
with
the
locating
lug
on
the
power
unit.
Push
to
lock.
Rectangular foam filter
This
is
housed
within
the
removable
grille
at
the
back
of
the
power
unit.
Remove
the
grille
by
pressing
the
release
button
(see
fig.
15)
wash
it
with
soao
and
water
and
dry
it
completely
before
replacing
it
in
the
grille.
Ensure
that
the
release
button
of
the
grille
slots
back
into
position.