Electrolux EFC9660 User manual

EFC 9660-9661
User manual
Manual de instrucciones
Manual de instruções

electroluxelectrolux
electroluxelectrolux
electrolux safety warnings 33
33
3
GB
WW
WW
Welcome to the world of Electrelcome to the world of Electr
elcome to the world of Electrelcome to the world of Electr
elcome to the world of Electroluxolux
oluxolux
olux
Thank you for choosing a first class
product from Electrolux, which
hopefully will provide you with lots of
pleasure in the future. The Electrolux
ambition is to offer a wide variety of
quality products that make your life
more comfortable. You find some
examples on the cover in this manual.
Please take a few minutes to study this
manual so that you can take advantage
of the benefits of your new machine.
We promise that it will provide a
superior User Experience delivering
Ease-of-Mind.
Good luck!

44
44
4 electrelectr
electrelectr
electroluxolux
oluxolux
olux contents
GB
Contents
Safety warnings ................................ 6
Description of the Appliance ............. 7
Control Panel.................................... 8
Maintenance and Care ................... 11
Special accessories ........................ 15
Something Not Working.................. 15
Installation ...................................... 16
The following symbols are used in this user manual:
Important information concerning your personal safety and information on
how to avoid damaging the appliance.
General information and tips.
Environmental information.

electroluxelectrolux
electroluxelectrolux
electrolux safety warnings 55
55
5
GB
Safety warnings
For the userFor the user
For the userFor the user
For the user
• The cooker hood is designed to
extract unpleasant odours from the
kitchen, it will not extract steam.
• Always cover lighted elements, to
prevent excess heat from damaging
the appliance. In the case of oil, gas
and coal fired cookers it is essential
to avoid open flames.
• Also, when frying, keep the deep
frying pan on the cooker top/cooker
under careful control.
• The hot oil in the frying pan might
ignite due to overheating.
• The risk of self-ignition increases
when the oil being used is dirty.
• It is extremely important to note that
overheating can cause a fire.
•Never carry out any flambé cookingNever carry out any flambé cooking
Never carry out any flambé cookingNever carry out any flambé cooking
Never carry out any flambé cooking
under the hood.under the hood.
under the hood.under the hood.
under the hood.
•Always disconnect the unit frAlways disconnect the unit fr
Always disconnect the unit frAlways disconnect the unit fr
Always disconnect the unit from theom the
om theom the
om the
power supply beforpower supply befor
power supply beforpower supply befor
power supply before carrying oute carrying out
e carrying oute carrying out
e carrying out
any work on the hood, includingany work on the hood, including
any work on the hood, includingany work on the hood, including
any work on the hood, including
rr
rr
replacing the light bulbeplacing the light bulb
eplacing the light bulbeplacing the light bulb
eplacing the light bulb (take the
cartridge fuse out of the fuse holder
or switch off the automatic circuit
breaker).
•It is very important to clean the hoodIt is very important to clean the hood
It is very important to clean the hoodIt is very important to clean the hood
It is very important to clean the hood
and rand r
and rand r
and replace the filter at theeplace the filter at the
eplace the filter at theeplace the filter at the
eplace the filter at the
rr
rr
recommended intervals. Failurecommended intervals. Failur
ecommended intervals. Failurecommended intervals. Failur
ecommended intervals. Failure toe to
e toe to
e to
do so could cause grdo so could cause gr
do so could cause grdo so could cause gr
do so could cause grease depositsease deposits
ease depositsease deposits
ease deposits
to build up, rto build up, r
to build up, rto build up, r
to build up, resulting in a firesulting in a fir
esulting in a firesulting in a fir
esulting in a fire hazare hazar
e hazare hazar
e hazard.d.
d.d.
d.
• The appliance is not intended for use
by young children or infirm persons
without supervision.
• Older children must be supervised if
using the appliance.
• Young children should be supervised
to ensure that they do not play with
the appliance.
••
••
•WW
WW
WARNING -ARNING -
ARNING -ARNING -
ARNING - Ensure that the
appliance is switched off before
replacing the lamp to avoid the
possibility of electric shock.
This appliance is marked according to
the European directive 2002/96/EC on
Waste Electrical and Electronic
Equipment (WEEE).
By ensuring this product is disposed of
correctly, you will help prevent potential
negative consequences for the
environment and human health, which
could otherwise be caused by
inappropriate waste handling of this
product.
The symbol on the product, or on
the documents accompanying the
product, indicates that this appliance
may not be treated as household
waste. Instead it shall be handed over
to the applicable collection point for the
recycling of electrical and electronic
equipment.
Disposal must be carried out in
accordance with local environmental
regulations for waste disposal.
For more detailed information about
treatment, recovery and recycling of
this product, please contact your local
city office, your household waste
disposal service or the shop where you
purchased the product.

66
66
6 electrelectr
electrelectr
electroluxolux
oluxolux
olux safety warnings
GB
For the installerFor the installer
For the installerFor the installer
For the installer
• When used as an extractor unit, the
hood must be fitted with a hose
having preferably the same diameter
as the outlet hole.
Attention:Attention:
Attention:Attention:
Attention: The hose is not supplied
and must be purchased separately.
••
••
•When installing the hood, make surWhen installing the hood, make sur
When installing the hood, make surWhen installing the hood, make sur
When installing the hood, make suree
ee
e
you observe the following minimumyou observe the following minimum
you observe the following minimumyou observe the following minimum
you observe the following minimum
distance frdistance fr
distance frdistance fr
distance from the top edge of theom the top edge of the
om the top edge of theom the top edge of the
om the top edge of the
cooking hob/ring surfaces:cooking hob/ring surfaces:
cooking hob/ring surfaces:cooking hob/ring surfaces:
cooking hob/ring surfaces:
electric cookerselectric cookers
electric cookerselectric cookers
electric cookers 500 mm500 mm
500 mm500 mm
500 mm
gas cookersgas cookers
gas cookersgas cookers
gas cookers 650 mm650 mm
650 mm650 mm
650 mm
If the instructions for installation for
the gas hob specify a greater
distance, this must be adhered to.
• The national Standard on fuel-
burning systems specifies a maxi-
mum depression of 0.04 mbar in
such rooms.
• The air outlet must not be connected
to chimney flues or combustion gas
ducts. The air outlet must under no
circumstances be connected to
ventilation ducts for rooms in which
fuel-burning appliances are installed.
• The air outlet installation must comply
with the regulations laid down by the
relevant local authorities.
• When the unit is used in extraction
mode, a sufficiently large ventilation
hole must be provided, with
dimensions that are approximately
the same as the outlet hole.
• National and regional building
regulations impose a number of
restrictions on using hoods and fuel-
burning appliances connected to a
chimney, such as coal or oil room-
heaters and gas fires, in the same
room.
• Hoods can only be used safely with
appliances connected to a chimney if
the room and/or flat (air/environment
combination) is ventilated from
outside using a suitable ventilation
hole approximately 500-600 cm2
large to avoid the possibility of a
depression being created during
operation of the hood.
• If you have any doubts, contact the
relevant controlling authority or
building inspector’s office.
• Since the rule for rooms with fuel
burning appliances is “outlet hole of
the same size as the ventilation hole”,
a hole of 500-600 cm2, which is to
say a larger hole, could reduce the
performance of the extractor hood.
• If the hood is used in its recirculation
mode, it will operate simply and safely
in the above conditions without the
need for any of the aforementioned
measures.
• When the hood is used in its
extraction mode, the following rules
must be followed to obtain optimal
operation:
- short and straight outlet hose
- keep bends in outlet hose to a
minimum
- never install the hoses with an
acute angle, they must always
follow a gentle curve.
- keep the hose as large as possible
(preferably the same diameter as
the outlet hole).
- the length should be no more than:
3 metres with one 90° bend
2 metres with two 90° bends
Bends of more than 90° will reduce
the efficiency of the hood and
reduce the airflow.
• Failure to observe these basic
instructions will drastically reduce the
performance and increase the noise
levels of the extractor hood.

electroluxelectrolux
electroluxelectrolux
electrolux description of the appliance 77
77
7
GB
Description of the Appliance
•The cooker hood is designed toThe cooker hood is designed to
The cooker hood is designed toThe cooker hood is designed to
The cooker hood is designed to
extract unpleasant odours frextract unpleasant odours fr
extract unpleasant odours frextract unpleasant odours fr
extract unpleasant odours from theom the
om theom the
om the
kitchen, it will not extract steam.kitchen, it will not extract steam.
kitchen, it will not extract steam.kitchen, it will not extract steam.
kitchen, it will not extract steam.
• The hood is supplied as an extractor
unit and can also be used with a
recirculation mode by fitting a
charcoal filter.
Extraction modeExtraction mode
Extraction modeExtraction mode
Extraction mode
• In this mode fumes are extracted to
the outside via a hosehose
hosehose
hose connected to
the coupling ringcoupling ring
coupling ringcoupling ring
coupling ring.
• In order to obtain the best performan-
ce the hose should have a diameter
equal to the outlet hole.
RecirRecir
RecirRecir
Recirculation modeculation mode
culation modeculation mode
culation mode
• The air is filtered through a charchar
charchar
charcoalcoal
coalcoal
coal
filterfilter
filterfilter
filter and returned to the kitchen.
• You will need an original charcoal filter
for the recirculation mode. (See
Special Accessories).
biegsames Rohr
Coupling ringCoupling ring
Coupling ringCoupling ring
Coupling ring

88
88
8 electrelectr
electrelectr
electroluxolux
oluxolux
olux control panel
GB
Control Panel
• Best results are obtained by using a low speed for normal conditions and a high
speed when odours are more concentrated.
Turn the hood on a few minutes before you start cooking.
The hood should be left on after cooking for about 15 minutes or until all the
odours have disappeared.
•CorrCorr
CorrCorr
Correct ventilation:ect ventilation:
ect ventilation:ect ventilation:
ect ventilation: If the cooker hood is to work correctly there must be an
under pressure in the kitchen. It is important to keep the kitchen windows
closed and have a window in an adjacent room open.
• The control switches are located on the hood’s front panel:
Model EFC 9661Model EFC 9661
Model EFC 9661Model EFC 9661
Model EFC 9661
•Light switch (ON/OFF):Light switch (ON/OFF):
Light switch (ON/OFF):Light switch (ON/OFF):
Light switch (ON/OFF): this switch is used to turn the light fitted in the hood on
and off.
•ON/OFF motor speed key:ON/OFF motor speed key:
ON/OFF motor speed key:ON/OFF motor speed key:
ON/OFF motor speed key: serves to enable and disenable the speed selection
keys.
•Push-button 1 (ON/OFF):Push-button 1 (ON/OFF):
Push-button 1 (ON/OFF):Push-button 1 (ON/OFF):
Push-button 1 (ON/OFF): used to set the fan to speed 1.
•Push-button 2 (ON/OFF):Push-button 2 (ON/OFF):
Push-button 2 (ON/OFF):Push-button 2 (ON/OFF):
Push-button 2 (ON/OFF): used to set the fan to speed 2.
•Push-button 3 (ON/OFF):Push-button 3 (ON/OFF):
Push-button 3 (ON/OFF):Push-button 3 (ON/OFF):
Push-button 3 (ON/OFF): used to set the fan to speed 3.
Light switchLight switch
Light switchLight switch
Light switch
(ON/OFF)(ON/OFF)
(ON/OFF)(ON/OFF)
(ON/OFF)
ON/OFF motorON/OFF motor
ON/OFF motorON/OFF motor
ON/OFF motor
speed keyspeed key
speed keyspeed key
speed key
Push-button 2Push-button 2
Push-button 2Push-button 2
Push-button 2
(ON/OFF)(ON/OFF)
(ON/OFF)(ON/OFF)
(ON/OFF)
Push-button 1Push-button 1
Push-button 1Push-button 1
Push-button 1
(ON/OFF)(ON/OFF)
(ON/OFF)(ON/OFF)
(ON/OFF) Push-button 3Push-button 3
Push-button 3Push-button 3
Push-button 3
(ON/OFF)(ON/OFF)
(ON/OFF)(ON/OFF)
(ON/OFF)

electroluxelectrolux
electroluxelectrolux
electrolux control panel 99
99
9
GB
Model EFC 9660Model EFC 9660
Model EFC 9660Model EFC 9660
Model EFC 9660
123 456
ab
• The hood can also be commanded from the control panel or the remote control.
(the remote control is a special accessory and is ordered separately).
11
11
1.Mains switch, ON/OFF
Press for less than 1 1/2 seconds and the cooker hood goes into the "stand bystand by
stand bystand by
stand by"
position (point "b" is illuminated).
Press for more than 1 1/2 seconds and the cooker hood turns OFF, ALL the
controls (except the light push button) are disabled (the display is off).
Press again for more than 1 1/2 seconds to reset the cooker hood to "stand
by".
22
22
2.Light switch, ON/OFF
33
33
3.Display
44
44
4.Start and choice of motor speed 1-2-3-1-2.........
55
55
5.Intensive speed on/off. The Intensive speed runs for 5 minutes:
If the hood is on when the Intensive speed is activated, the hood will revert to
previous speed after 5 minutes.
If the hood is off when the Intensive speed is activated, the hood will
automatically turn off after 5 minutes.
To interrupt the Intensive speed, press button 11
11
1 or 44
44
4.
The letter PP
PP
P appears on the display and the remaining time (the point “aa
aa
a” is
flashing), if interrupted an acoustic signal is heard.
66
66
6.Self-Timer: times all the speed levels (the point “bb
bb
b” is flashing), and then the
cooker hood switches off:
The self-timer is set as follows:
1st speed level 20 minutes
2nd speed level 15 minutes
3rd speed level 10 minutes
The display shows the remaining operation time, at the end of the time an
acoustic signal is heard. Depressing the push-button again exits the function.
Should the hood or the controls fail to operate: disconnect the power supply for at
least 5 seconds. After reconnecting the power supply wait 15 seconds and then
check that the cooker hood is now operating
correctly.

1010
1010
10 electrelectr
electrelectr
electroluxolux
oluxolux
olux control panel
GB
GrGr
GrGr
Grease and charease and char
ease and charease and char
ease and charcoal filtercoal filter
coal filtercoal filter
coal filter
maintenance indicatormaintenance indicator
maintenance indicatormaintenance indicator
maintenance indicator
This hood is fitted with a device that
indicates when it is necessary to clean
the grease filter or the charcoal filter (if
the hood is used in the recirculation
version with a charcoal filter).
On delivery, the hood is not supplied
with a charcoal filter, so the saturation
indicator will be disabled.
If the hood is to be used with a
charcoal filter, the saturation
indicator light must be enabled as
follows:
Set in "Stand byStand by
Stand byStand by
Stand by" the hood.
Press buttons 44
44
4 and 55
55
5 simultaneously
and hold them for 3 seconds. At first
only the grease filter LED FF
FF
F will light up,
but when the charcoal filter LED CC
CC
C
lights up the saturation indicator will be
enabled.
To disable it: Press buttons 44
44
4 and 55
55
5
again simultaneously and hold
them for 3 seconds, until the charcoal
filter LED goes out.
Grease filter LED (F)
LED FF
FF
F will start to flash when it is time
to clean the grease filter.
Cleaning will be necessary after 40
working hours. Always comply with the
maintenance instructions for the grease
filter.
Charcoal filter LED (C)
The charcoal filter LED CC
CC
C will start to
flash when the charcoal filter needs to
be replaced.
This operation is necessary after
approximately 160 working hours.
Resetting the saturation indicator
After cleaning or replacing the filters,
press button 11
11
1 for 3 seconds until the
grease filter LED FF
FF
F or the charcoal filter
LED CC
CC
C stops flashing.

electroluxelectrolux
electroluxelectrolux
electrolux maintenance and care 1111
1111
11
GB
Maintenance and Care
••
••
•BeforBefor
BeforBefor
Before performing any maintenance operation, isolate the hood fre performing any maintenance operation, isolate the hood fr
e performing any maintenance operation, isolate the hood fre performing any maintenance operation, isolate the hood fr
e performing any maintenance operation, isolate the hood from theom the
om theom the
om the
electrical supply by switching ofelectrical supply by switching of
electrical supply by switching ofelectrical supply by switching of
electrical supply by switching off at the connector and rf at the connector and r
f at the connector and rf at the connector and r
f at the connector and removing theemoving the
emoving theemoving the
emoving the
connector fuse.connector fuse.
connector fuse.connector fuse.
connector fuse.
Or if the appliance has been connected thrOr if the appliance has been connected thr
Or if the appliance has been connected thrOr if the appliance has been connected thr
Or if the appliance has been connected through a plug and socket, then theough a plug and socket, then the
ough a plug and socket, then theough a plug and socket, then the
ough a plug and socket, then the
plug must be rplug must be r
plug must be rplug must be r
plug must be removed fremoved fr
emoved fremoved fr
emoved from the socket.om the socket.
om the socket.om the socket.
om the socket.
Metal grMetal gr
Metal grMetal gr
Metal grease filterease filter
ease filterease filter
ease filter
• The purpose of the grease filters is to
absorb grease particles which form
during cooking and it mustmust
mustmust
must always be
used, either in the external extraction
or internal re-circulation function.
Attention: the metal grease filters
must be removed and washed, either
by hand or in the dishwasher, every
four weeks.
Removing the metal grRemoving the metal gr
Removing the metal grRemoving the metal gr
Removing the metal grease filterease filter
ease filterease filter
ease filter
• Use the spring handle and remove
the filter downward.
Hand washingHand washing
Hand washingHand washing
Hand washing
Soak grease filters for about one hour
in hot water with a grease-loosening
cleaner, then rinse off thoroughly with
hot water. Repeat the process if
necessary. Refit the grease filters
when they are dry.
DishwasherDishwasher
DishwasherDishwasher
Dishwasher
Place grease filters in the dishwasher.
Select most powerful washing
programme and highest temperature,
at least 65°C. Repeat the process.
Refit the grease filters when they are
dry.
When washing the metal grease filter
in the dishwasher a slight
discolouration of the filter can occur,
this does not have any impact on its
performance.
• Clean the inner housing using a hand
hot solution only(never use caustic
detergents, abrasive powders or
brushes).
EFC 9660EFC 9660
EFC 9660EFC 9660
EFC 9660
EFC 9661EFC 9661
EFC 9661EFC 9661
EFC 9661

1212
1212
12 electrelectr
electrelectr
electroluxolux
oluxolux
olux maintenance and care
GB
CharChar
CharChar
Charcoal filtercoal filter
coal filtercoal filter
coal filter
• The charcoal filter should only be
used if you want to use the hood in
recirculation mode.
• To do this you will need an original
charcoal filter (available from your
local Service Force Centre).
•Cleaning/rCleaning/r
Cleaning/rCleaning/r
Cleaning/replacing the chareplacing the char
eplacing the chareplacing the char
eplacing the charcoal filtercoal filter
coal filtercoal filter
coal filter
Unlike other charcoal filters, the
LONGLIFE charcoal filter can be
cleaned and reactivated.
With normal use the filter should be
cleaned every second month (when
using the hood 2,5 hours per day,on
avarage). The best way to clean the
filter is in the dishwasher. Use normal
detergent and choose the highest
temperature (65º C). Wash the filter
separately so that no food parts gets
stuck on the filter and later causes bad
odours. To reactivate the charcoal, the
filter should be dried in an oven for 10
minutes with a maximum temperature
of 100º C.
After approximately three years of use,
the charcoal filter should be replaced
with a new, as the odour reduction
capacity will be reduced.
•FittingFitting
FittingFitting
Fitting
Remove the frame iiiii which supports
the filter hh
hh
h by turning 90° the two
knobs g.g.
g.g.
g.
Insert the charcoal filter inside the
frame and put all parts back in their
place.
•TT
TT
To ro r
o ro r
o removeemove
emoveemove
emove proceed in the reverse
order.
• Always specify the hood model code
number and serial number when
ordering replacement filters. This
information is shown on the rating
plate located on the inside of the unit.
• The charcoal filter can be ordered
from your local Service Force Centre.
g
j
h
i
g
g
g

electroluxelectrolux
electroluxelectrolux
electrolux maintenance and care 1313
1313
13
GB
WW
WW
Warar
arar
arningning
ningning
ning
• Failure to observe the instructions on
cleaning the unit and changing the
filters will cause a fire hazard. You are
therefore strongly recommended to
follow these instructions.
• The manufacturer declines all
responsibility for any damage to the
motor or any fire damage linked to
inappropriate maintenance or failure
to observe the above safety
recommendations.
Changing the light bulb(s)Changing the light bulb(s)
Changing the light bulb(s)Changing the light bulb(s)
Changing the light bulb(s)
•Disconnect the cooker hood frDisconnect the cooker hood fr
Disconnect the cooker hood frDisconnect the cooker hood fr
Disconnect the cooker hood fromom
omom
om
the mains supplythe mains supply
the mains supplythe mains supply
the mains supply..
..
.
••
••
•Prior to touching the light bulbsPrior to touching the light bulbs
Prior to touching the light bulbsPrior to touching the light bulbs
Prior to touching the light bulbs
ensurensur
ensurensur
ensure they are they ar
e they are they ar
e they are cooled down.e cooled down.
e cooled down.e cooled down.
e cooled down.
• Replace the old bulb with a new one
of the same type.
• If the light does not come on, make
sure the bulb has been inserted in
correctly before contacting your local
Service Force Centre.

1414
1414
14 electrelectr
electrelectr
electroluxolux
oluxolux
olux maintenance and care
GB
Cleaning the hoodCleaning the hood
Cleaning the hoodCleaning the hood
Cleaning the hood
• Clean the outside of the hood using a
damp cloth and a solution of water
and mild washing up liquid.
• Never use corrosive, abrasive or
flammable cleaning products or
products containing bleach.
• Never insert pointed objects in the
motor’s protective grid.
• Only ever clean the switch panel and
filter grill using a damp cloth and mild
washing up liquid.
• It is extremely important to clean the
unit and change the filters at the
recommended intervals. Failure to do
so will cause grease deposits to build
up that could constitute a fire hazard.

electroluxelectrolux
electroluxelectrolux
electrolux special accessories 1515
1515
15
GB
Special accessoriesSpecial accessories
Special accessoriesSpecial accessories
Special accessories
CharChar
CharChar
Charcoal filtercoal filter
coal filtercoal filter
coal filter Type 20
Remote contrRemote contr
Remote contrRemote contr
Remote controlol
olol
ol RM 6940 E-Nr. 942 122 002
Something Not Working
If your appliance fails to work properly please carry out the following checks.
SymptomSymptom
SymptomSymptom
Symptom
The cooker hood will not start...
The cooker hood is not working
The cooker hood has switched off
during operation...
SolutionSolution
SolutionSolution
Solution
Check that:Check that:
Check that:Check that:
Check that: The hood is connected
to the electricity supply.
Check that a fan speed has been
selected.
Check that:Check that:
Check that:Check that:
Check that: The fan speed is set high
enough for the task.
The grease filters are clean.
The kitchen is adequately vented to
allow the entry of fresh air.
If set up for recirculation, check that
the charcoal filter is still effective.
If set up for extraction, check that the
ducting and outlets are not blocked.
The safety cut-out device has been
tripped. Turn off the hob and then wait
for the device to reset. If the hood has
been installed below the heights
indicated in the installation instructions
the motor will cut-out frequently which
will damage the hood.
If after all these checks, the problem persists, contact your local Service Centre,
quoting the model and serial number.
Please note that it will be necessary to provide proof of purchase for any in-
guarantee service calls.
In-guarantee customers should ensure that the above checks have been made as
the engineer will make a charge if the fault is not a mechanical or electrical
breakdown.

1616
1616
16 electrelectr
electrelectr
electroluxolux
oluxolux
olux installation
GB
Installation
TT
TT
Technical Detailsechnical Details
echnical Detailsechnical Details
echnical Details
EFC 9660EFC 9660
EFC 9660EFC 9660
EFC 9660 EFC 9661EFC 9661
EFC 9661EFC 9661
EFC 9661
Dimensions (in cm):Dimensions (in cm):
Dimensions (in cm):Dimensions (in cm):
Dimensions (in cm):
Height (Extraction mode): 71/115 71/115
Height (Recirculation mode): 80,7/126,5 80,7/126,5
Width: 89,8 89,8
Depth: 50 50
MaximumMaximum
MaximumMaximum
Maximum absorbedabsorbed
absorbedabsorbed
absorbed power:power:
power:power:
power: 215 W215 W
215 W215 W
215 W 200 W200 W
200 W200 W
200 W
Motor: 175 W 170 W
Lighting: 2 x 20 W (G4) 2 x 20 W (G4)
Length of the cable:Length of the cable:
Length of the cable:Length of the cable:
Length of the cable: 150 cm150 cm
150 cm150 cm
150 cm 150 cm150 cm
150 cm150 cm
150 cm
Electrical connection:Electrical connection:
Electrical connection:Electrical connection:
Electrical connection: 220-240 V220-240 V
220-240 V220-240 V
220-240 V 230 V230 V
230 V230 V
230 V
Fuse rating:Fuse rating:
Fuse rating:Fuse rating:
Fuse rating: 5A T5A T
5A T5A T
5A T 5A T5A T
5A T5A T
5A T
Mounting accessories includedMounting accessories included
Mounting accessories includedMounting accessories included
Mounting accessories included
1 deflector (with extensions)
1 Allan wrench for torx screws
1 fixing bracket for motor unit
1 support bracket for flues (3 pieces to assemble)
5 screws 5 x 45 mm
5 dowels Ø 8 mm
4 screws 2.9 x 6.5
4 screws 3.5 x 9.5
4 screws 4 x 8
2 screws 3.5 x 13
1 bracket for fixing the mantle
4 screws and bushes for fixing the mantle

electroluxelectrolux
electroluxelectrolux
electrolux installation 1717
1717
17
GB
Electrical connection
(not for UK)
Safety warSafety war
Safety warSafety war
Safety warnings for the electriciannings for the electrician
nings for the electriciannings for the electrician
nings for the electrician
Before connecting the appliance to the
power supply, check that the voltage
indicated on the rating plate
corresponds to the mains power supply
available. Appliances fitted with a plug
can be connected to any standard
power socket within easy access.
Should it be necessary to provide a
fixed connection, the hood must only
be installed by an electrician authorised
by the local electricity board. When
installing, an omnipolar disconnector
with a distance of at least 3 mm
between contacts must be provided.
Fixed connection of the appliance must
only be carried out by an authorised
electrician.
Electrical connection for
UK only
Safety warSafety war
Safety warSafety war
Safety warnings for the electriciannings for the electrician
nings for the electriciannings for the electrician
nings for the electrician
Connect the hood to the mains supply
via a double pole switch which has 3
mm minimum separation between the
contacts.
The switch must be accessible at all
times.
The following is valid in the United
Kingdom only:
- the wire which is coloured green and
yellow must be connected to the
terminal which is marked with the
letter E or by the earth symbol ( ),
or coloured green or green and
yellow;
- the wire which is coloured blue must
be connected to the terminal which is
marked with the letter N or coloured
black, -
- the wire which is coloured brown
must be connected to the terminal
which is marked with the letter L or
coloured red.
BROWN
CORD CLAMP
BLUE
GREEN & YELLOW
5AT




1818
1818
18 electrelectr
electrelectr
electroluxolux
oluxolux
olux installation
GB
Installing the mantle on the hoodInstalling the mantle on the hood
Installing the mantle on the hoodInstalling the mantle on the hood
Installing the mantle on the hood
Installing the mantle can also be carried
out after having installed the motor unit
at the wall.
This makes installation easier because
the weights and dimensions of the
parts to be mounted are relatively
limited.
On the contrary, installing the mantle
before installing the hood to the wall
allows checking the set up and position
of the hood to the wall.
Proceed as follows:
• Place the mantle over the hood (the
painted part downward).
The slots on the glass element should
correspond to the fixing points on the
hood.
• Put the closure bracket over the
mantle and fix the glass element with
four bushes and screws.

electroluxelectrolux
electroluxelectrolux
electrolux installation 1919
1919
19
GB
First decide which functioningFirst decide which functioning
First decide which functioningFirst decide which functioning
First decide which functioning
version is better for youversion is better for you
version is better for youversion is better for you
version is better for you
If you decide to use the hood in
exhausting version we suggest to
position the upper section of the
chimney so that the oulet slots are not
visible once installation has ended, on
the contrary if is decided to use the
hood in recycling version BE SURE that
the side with slots is up (see also A-B-
C sequence).
Assembling the chimney flue
support/bracket (3 parts)
The three parts should be fixed with 4
screws, the support extension is
adjustable and should correspond to
the internal width of the telescopic
chimney flue.
Assembling the deflector (3 parts –Assembling the deflector (3 parts –
Assembling the deflector (3 parts –Assembling the deflector (3 parts –
Assembling the deflector (3 parts –
only for filter version):only for filter version):
only for filter version):only for filter version):
only for filter version):
The three parts should be fixed with 2
screws, the deflector extension is
adjustable and should correspond to
the width of the chimney flue support,
to which it is then fixed.
A
B
180°
C - OK!
==
X
X
G
4 x Ø 4x8
=
=
X
F
F
G
2 x
Ø 3,5 x 13
4 x
Ø 3,5 x 9,5

2020
2020
20 electrelectr
electrelectr
electroluxolux
oluxolux
olux installation
GB
InstallationInstallation
InstallationInstallation
Installation
Make surMake sur
Make surMake sur
Make sure that the cooker hood is disconnected fre that the cooker hood is disconnected fr
e that the cooker hood is disconnected fre that the cooker hood is disconnected fr
e that the cooker hood is disconnected from the power supply beforom the power supply befor
om the power supply beforom the power supply befor
om the power supply beforee
ee
e
carrying out the installation.carrying out the installation.
carrying out the installation.carrying out the installation.
carrying out the installation.
Remove the anti-fat filter and the carbon filter support frame.
• Mark the wall with a centre line, this will aid mounting procedure (1)(1)
(1)(1)
(1), position the
template so that the mid line printed on the template matches with the centre
line previously drawn, the lower side of the template corresponds to the lower
side of the hood once mounted (2)(2)
(2)(2)
(2).
• Drill two holes Ø 8mm and fix the support bracket with two wall plugs and
screws (3)(3)
(3)(3)
(3). Hang the hood (4)(4)
(4)(4)
(4) and adjust its position (5-6)(5-6)
(5-6)(5-6)
(5-6).
• From the inside of the hood sign 1 point for definitive fixing (7)(7)
(7)(7)
(7).
• Remove the hood (8)(8)
(8)(8)
(8) and drill 1 hole Ø 8mm (9)(9)
(9)(9)
(9), fit 1 wall plug (10)(10)
(10)(10)
(10).
• Drill two holes Ø 8mm on the upper side close to the ceilling, fit two wall plugs
(11)(11)
(11)(11)
(11) (In case the hood is to be used in filter versionfilter version
filter versionfilter version
filter version, mount the deflector FF
FF
F on
the chimney support with 4 screws) and fix the chimney support GG
GG
G with two
screws (12)(12)
(12)(12)
(12).
• Hang the hood again (13)(13)
(13)(13)
(13) and fix it definitively with 1 screw (14)(14)
(14)(14)
(14).
• Fit an exhausting pipe (15)(15)
(15)(15)
(15) to connect the outlet hole BB
BB
B of the hood to the
outside (Extractor hood) or to the deflector FF
FF
F (Filter version).
• Make electrical connection (16)(16)
(16)(16)
(16).