Electrolux PLHV42P8CC User manual

OWNERS GUIDE - Range Hood
PLHV42P8CC
PLHV42P8CC - P/N 316137229 (Pub. No. 5995392114)
GUIDE DE LUTILISATEUR - Hotte de cuisine
MANUAL PARA EL PROPIETARIO - Ca pana extractora
READ AND SAVE THESE INSTRUCTIONS
LISEZ ET CONSERVEZ CES INSTRUCTIONS
LEER Y GUARDAR ESTAS INSTRUCCIONES
F
UK E
Get other manuals https://www.bkmanuals.com

2
Product Registration
Register your Product
The self-addressed PRODUCT
REGISTRATION CARD should be
filled in completely, signed and returned
to the Frigidaire Canada.
This Owners Guide contains general
operating instructions for your range
hood and feature information for several
models. our range hood may not have
all the described features.
Note: The instructions appearing in this
Owners Guide are not meant to cover
every possible condition and situation
that may occur. Common sense and
caution must be practiced when
installing, operating and maintaining any
appliance.
Thank you or choosing this appliance. The information contained within this
Owners Guide will instruct you on how to properly operate and care for your range
hood. Please read through the information contained in your literature pack to learn
more about your new appliance.
Record Your Model and Serial Numbers
Record in the space provided below the model and serial numbers found on the serial
plate located on the right hand side of the range hood.
Model Number: ________________________________________________
Serial Number: ________________________________________________
Date o Purchase: ______________________________________________
Contents 2
Table des matières 12
Indice 23
Contents
Product Registration....................................................................................... 2
Important Safety Instructions .......................................................................... 3
Installation................................................................................................... 4-8
Use and Care ................................................................................................. 9
Hood Cleaning .............................................................................................. 10
Lights Replacement ..................................................................................... 10
Warranty ...................................................................................................... 11
Get other manuals https://www.bkmanuals.com

3
Important Safety Instructions
READ AND SAVE THESE INSTRUCTIONS
Take care when using cleaning agents or detergents.
Suita le for use in household cooking area
CAUTION - To reduce risk of fire and to properly exhaust air, be sure to duct air outside  Do not vent exhaust air into
spaces within walls or ceilings or into attics, crawl spaces, or garages.
CAUTION - For General Ventilating Use Only. Do Not Use To Exhaust Hazardous Or Explosive Materials And Vapors.
WARNING  TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJUR TO PERSONS, OBSERVE THE
FOLLOWING:
a. Use this unit only in the manner intended by the manufacturer. If you have questions, contact the manufacturer.
b. Before servicing or cleaning unit, switch power off at service panel and lock the service disconnecting means to prevent
power from being switched on accidentally. When the service disconnecting means cannot be locked, securely fasten
a prominent warning device, such as a tag, to the service panel.
WARNING  TO REDUCE THE RISK OF A RANGE TOP GREASE FIRE:
a. Never leave surface units unattended at high settings. Boilovers cause smoking and greasy spillovers that may ignite.
Heat oils slowly on low or medium settings.
b. Always turn hood ON when cooking at high heat or when flambeing food (i.e. Crepes Suzette, Cherries Jubilee,
Peppercorn Beef Flambee).
c. Clean ventilating fans frequently. Grease should not be allowed to accumulate on fan or filter.
d. Use proper pan size. Always use cookware appropriate for the size of the surface element.
WARNING  TO REDUCE THE RISK OF INJUR TO PERSONS IN THE EVENT OF A RANGE TOP GREASE FIRE,
OBSERVE THE FOLLOWING:
a. SMOTHER FLAMES with a close-fitting lid, cookie sheet, or metal tray, then turn off the burner. BE CAREFUL TO
PREVENT BURNS. If the flames do not go out immediately, EVACUATE AND CALL THE FIRE DEPARTMENT.
b. NEVER PICK UP A FLAMING PAN  ou may be burned.
c. DO NOT USE WATER, including wet dishcloths or towels  a violent steam explosion will result.
d. Use an extinguisher ONL if:
1. ou know you have a Class ABC extinguisher, and you already know how to operate it.
2. The fire is small and contained in the area where it started.
3. The fire department is being called.
4. ou can fight the fire with your back to an exit.
WARNING  TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJUR TO PERSONS, OBSERVE THE
FOLLOWING:
a) Installation work and electrical wiring must be done by qualified person(s) in accordance with all applicable codes and
standards, including fire-rated construction.
b) Sufficient air is needed for proper combustion and exhausting of gases through the flue (chimney) of fuel burning
equipment to prevent back drafting. Follow the heating equipment manufacturers guideline and safety standards such
as those published by the National Fire Protection Association (NFPA), and the American Society for Heating,
Refrigeration and Air Conditioning Engineers (ASHRAE), and the local code authorities.
c) When cutting or drilling into wall or ceiling, do not damage electrical wiring and other hidden utilities.
d) Ducted fans must always be vented to the outdoors.
WARNING - TO REDUCE THE RISK OF FIRE, USE ONL METAL DUCTWORK.
WARNING - TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT USE THIS FAN WITH AN SOLID-
STATE SPEED CONTROL DEVICE.
WARNING
Electrical Shock Hazard - Can result in serious injury or death.
Disconnect appliance from electric power before servicing.
If equipped, the fluorescent light bulb contains small amounts of mercury which must be
recycled or disposed of according to Local, State, and Federal Codes.
Get other manuals https://www.bkmanuals.com

4
Installation FOR RESIDEN IAL USE ONLY
NO O BE INS ALLED OVER GAS GRILLS
PLEASE READ EN IRE INS RUC IONS BEFORE PROCEEDING.
INS ALLA ION MUS COMPLY WI H ALL LOCAL CODES.
IMPOR AN : Save these Instructions for the Local Electrical Inspectors use.
INS ALLER: Please leave these Instructions with this unit for the owner.
OWNER: Please retain these instructions for future reference.
Safety Warning: urn off power circuit at the service entrance and lock out
panel, before wiring this appliance.
Requirement: 120 V AC, 60 Hz. 15 or 20 A
Weight: 86 pounds
Diameter of Transition 8
Diameter of exhaust Duct required 8
Note: All dimensions are shown in inches.
* Dimensions are given from base of hood to ceiling, and include clearance
required for installation.
Dimensions - Table 1
Considerations before installing Hood
1. For the most efficient air flow exhaust, use a straight run or as few elbows as
possible.
CAUTION: Vent unit to outside of building, only.
2. If allowed in your area, use metallic flex ducting only to connect rigid duct
directly to transitions.
3. COLD WEATHER installations should have an additional backdraft damper
installed to minimize backward cold air flow and a nonmetallic thermal break to
minimize conduction of outside temperatures as part of the ductwork. The
damper should be on the cold air side of the thermal break. The break should
be as close as possible to where the ducting enters the heated portion of the
house.
4. Hood installation height above cooktop is specified in Figure 2. Be sure that your
hood model fits your installation.
Figure 1*
42 27
min. 33 13/16
max. 49 1/16
4
14 3/4 19 1/4
Get other manuals https://www.bkmanuals.com

5
ools required for installation
Screw driver (pozidrive n°2 , torx 10 and 20)
Allen spanner 4mm
Shifting spanner 10mm
pipe wrench 3/8
Electric drill with twist bit Ø 10 mm
Installation re-Installations Calculations (see Figure 2)
1. a) Select a hood preference height P (see Figure 2) that is comfortable for
the user not less than 30.
b) Calculate Hood height your installation H (see Figure 2). H = K-C-P.
c) Confirm that H is within the range of min to max H found for your hood.
If not adjust your installation.
d) Calculate Chimney structure height S (use formulas in Figure 2, and
check dimensions of your hood). Save this calculation for use later in the
installation.
reparation of Mounting Surface - Installing supports above
ceiling drywall.
Note: ake into consideration the hood depth; your hood could be much
deeper than the cooktop.
2. Mark center lines of cooktop or range on ceiling above. Use centerlines marked
on ceiling to position the mounting template. Note location of hood front, side,
and mounting holes indicated on template.
3. Remove and save template. Cut and remove ceiling drywall. Install suitable
length 2" x 4" lumber between joists to provide chimney mounting points as
shown in Fig. 4 and 5. Use template for dimensions and required clearance.
Make sure to affix the added lumber firmly and level. Consult a professional if you
have difficulties or your installation is unique. Consult template and Figures 3.
4. 5.
Note the weight o the appliance. (see Table1).
4. Install an 8 exhaust duct. Female end shall be 4-1/2" below finished ceiling and
securely fastened to joists. Do not use duct smaller than the transition.
5. Install 1/2" electrical conduit in location marked on template and extend length
S from ceiling.
6. Install drywall around duct and conduit; then refinish ceiling.
A
C (36"std.)
SH
K
P
K = Kitchen Height
C = Counter Height (36" standard)
P = Height of Hood Bottom above
counter not less than 30
A = Canopy Height
H = Hood height your installation
H = K  C  P
S=
Chimney Structure Height,
your installation.
S=H  A
Figure 2
Figure 3
Figure 4 Figure 5
Get other manuals https://www.bkmanuals.com

6
F
E
G
Appliance Installation
(Note: two people may be required for proper installation).
7. Install transition to top of hood (if removed for shipping). Snap damper into
transition, foam tape up , with firm pressure at either end. Mark onto exterior of
transition the 'V' location of the damper within. See Figure 6.
Note: Duct screws can ONLY go below this line.
8. Adjust chimney mounting structure to S dimension as determined in Step 1,
page 5. Use 2 screws per attachment leg. Do not fasten to ceiling now.
9. Set chimney mounting structure on top of hood canopy. Attach nuts loosely.
See Figure 7 and 8.
10. Fit duct piece on transition so that top end is 5-1/2" below top of chimney
structure, male end up.
11. Remove chimney structure from hood canopy.
12. Install Ducting. Fasten duct to transition with screws and tape per code.
Loosely fasten starter collar (included) flush to top of duct. Note: screws must
not hamper the damper (see 8. above for screw location).
Loosely fasten starter collar (included) flush to bottom of duct.
13. To install Chimney Structure to ceiling, use a 10mm or adjustable wrench or
flat head screwdriver. Drill pilot holes into ceiling. Attach mounting structure to
joists with the 4 lag screws provided. (Keep 1/2" conduit inside structure.) See
Figure 3.
14. To asten the canopy use a 10mm or adjustable wrench. Affix nuts to top of
canopy.
Do not tighten. Raise canopy up to chimney structure and twist in place. See
Figure 8. Tighten nuts securely.
15. Ducting or all units: There should be no more than 1" gap between canopy
ducting and house ducting. Adjust starting collar over both ducts. Tighten collar.
Fasten duct with screws and tape per code. Make final angular adjustment to
unit at ceiling if necessary, then securely tighten 4 ceiling lag screws if not
already tightened.
Installation
Figure 6
Figure 7
Figure 8
Get other manuals https://www.bkmanuals.com

7
Installation Wiring to ower Supply
WARNING!
ELECTRICAL GROUNDING INSTRUCTIONS
THIS APPLIANCE IS FITTED WITH AN ELECTRICAL JUNCTION BOX WITH
3 WIRES, ONE OF WHICH (GREEN/ ELLOW) SERVES TO GROUND THE
APPLIANCE. TO PROTECT OU AGAINST ELECTRIC SHOCK, THE
GREEN AND ELLOW WIRE MUST BE CONNECTED TO THE GROUNDING
WIRE IN OUR
HOME ELECTRICAL S STEM, AND IT MUST UNDER NO CIRCUMSTANCES
BE CUT OR REMOVED.
Warning: urn off power circuit at the service panel before wiring this unit.
120 VAC, 15 or 20 Amp circuit required.
16. Remove j-box cover as shown in Figure 10.
17. Remove the knockout and install the strain relief (conduit) connector (1/2") in
junction box.
18. Run 3 wires; black, white and green (#16 AWG) in 1/2" conduit from service panel
to junction box.
19. Connect black wire from service panel to black or red in junction box, white to
white and green to green-yellow. See Figure 10.
20. Close junction box cover, check all light bulbs to make sure they are secure in
their sockets, then turn power on in service panel and check lights and blower
operation per Care & Use section of this manual and install filters.
Final assembly
For final Chimney Cover installation, DO NO USE ELEC RIC SCREW
DRIVER.
21. Fit the nuts with fixing hooks supplied inside the top and bottom sections of the
chimney covers at all the rectangular slots. Figure 11-12.
22. Join the two top sections of the chimeny covers to cover the chimney structure.
Screw the two sections together with 4 screws (2 each side- see the plan
diagram for joining the two sections). Figure 11.
23. Fix the covers to the structure, near the ceiling, with two screws (one each side).
Figure 11.
Figure 10
Figure 11
Nut
rear
Chimney
cover
front
Chimney
cover
Top
chimney-to-structure
fixing point
Get other manuals https://www.bkmanuals.com

8
12345678
Nut
rear
Chimney
cover
front
Chimney
cover
X
X
Figure 12
Figure 13
Installation
24. Join the two bottom sections of the chimeny covers to cover the chimney
structure using 6 screws (3 each side, see the plan diagram for joining the two
sections). Figure 12.
25. Slide down the bottom section of the covers in its seat so that it completely
covers the motor compartment and electrical connection box. Figure 12.
26. Apply the 2 tabs (supplied) to cover the fixing points of the bottom flue (CAUTION!
THE BOTTOM FLUE TABS ARE THE NARROWER AND SHALLOWER
ONES).
The wider and deeper tabs are those used for the top flue, and must be cut to
size. Figure 13.
Attention!
Tabs must be ixed using the double sided adhesive tape supplied (two
segments each tab should be used!):
Cut the e tape into 8 segments, then remove the protection covering from both
sides and apply the segments close to the screws that fix the chimney flues to
the structure.
NOTE: Do not overtighten and de orm metal.
Turn the main power on again at the central electrical panel and check for correct
hood operation.
27. Make sure to leave this manual for the home owner.
Get other manuals https://www.bkmanuals.com

9
Use and Care
Control Pad Functions
Grease Filter Saturation LED
The Suction power 2 LED in Figure 12 is marked with an F. This LED will flash to remind you when the grease filter needs to
be cleaned after 40 hours use. Follow the instructions for cleaning filters in this booklet. Once the grease filters have been cleaned,
reset the reminder by pressing Motor OFF button for about 3 seconds until you hear the signal (beep).
Operating Instructions
The blower should be turned on for about 5 minutes be ore cooking in order to establish air currents upward through the hood.
Use the low speeds for normal use and the higher speeds for strong odors or fumes.
Minimize cross drafts which will reduce the effectiveness of the hood.
READ THE INSTRUCTIONS CAREFULL BEFORE USING THE HOOD.
For satisfactory use of your hood, become familiar with the various functions of the
hood as described below
Motor OFF button
ON button and
motor suction
power selection
button 1, 2, 3,
1,....
Suction power
1 LED, this led
is ON when
suction power
1 is selected.
Suction power
2 LED, this led
is ON when
suction power
2 is selected.
Suction power
3 LED, this led
is ON when
suction power
3 is selected.
Intensive
Suction power
LED, this led is
ON when the
intensive
suction power
is selected.
Intensive
Suction power
button - this
suction power
will function
for 10 mins.
then the hood
set again the
preselected
speed
Light OFF button
Light ON button
Figure 14
Get other manuals https://www.bkmanuals.com

10
Be sure lights are cool before cleaning the hood.
To Clean Filters
The metal grease filters will last forever.
They are made of anodized aluminum
It is recommended that the filters be washed at least once a month; they can
be washed by hand or in the dishwasher.
 Drain water through edge holes and let each filter dry thoroughly before replacing
it.
To Remove The Metal Grease Filters
 Disconnect the hood from electricity.
 Push clips towards the rear and pull the filters downward.
 Disengage each filter from a side and remove it
To Replace The Metal Grease Filters
 Reverse procedure.
To Clean Hood Surface
 For general care, wipe the outside of the stainless steel, white, black or glass
hood with sudsy water or household cleaners such as Fantastic® or Formula
409®, rinse well and dry with clean soft cloth to avoid water marks.
 Wipe and dry brushed stainless steel in the same direction as the grain.
 Do not use abrasive products.
 To remove finger prints and give added shine use spray cleaners such as
Stainless Steel Magic® and Shimmer®.
Hood Cleaning
NOTE: Turn blower and lights o . Make sure the lights are cool. If new lights
do not operate be sure lights are inserted correctly before calling service.
 Remove the light cover using a little flat screwdriver or similar tool as a lever.
 Remove the damaged light and replace with a new 12 Volt, 20 Watt (maximum)
halogen light made for a G-4 base. Follow package directions and do not touch
new light with bare hands.
 Reinstall the light cover (snap into position).
Lights replacement
Figure 15
Figure 16
Light
Light cover
Turn off electric power to hood before
removing light cover.
Get other manuals https://www.bkmanuals.com