Electrolux TC2 User manual

SERVICE MANUAL
WASHING
TC2
TC3
TC4
©ELECTROLUX HOME PRODUCTS
ITALY S.p.A.
Spares Operations Italy
Corso Lino Zanussi, 30
Publication
number
I - 33080 PORCIA /PN 599 72 84-41
Fax [phone]
S.O.I.
Edition: 03-2010
EN
Washing machines &
Washer-dryers
with electronic control
system
EWM21xx
EWM25xx
Functional and
technical characteristics
ENV06
Styling
TC 4 / 3 / 2
Time manager 1-2

SOI/DT 2010-03 dmm 2/78 599 72 84-41

SOI/DT 2010-03 dmm 3/78 599 72 84-41
CONTENTS
1Purpose of this manual.............................................................................................................................. 5
2WARNINGS .............................................................................................................................................. 5
3TC4........................................................................................................................................................... 6
3.1GENERAL CHARACTERISTICS........................................................................................................ 6
3.1.1General characteristics WM......................................................................................................... 6
3.1.2General characteristics WD ......................................................................................................... 7
3.2CONTROL PANEL............................................................................................................................. 8
3.2.1Styling TC4 WM/WD.................................................................................................................... 8
3.2.2Configuration of WM/WD control panel ........................................................................................ 9
3.2.3Programme selector (S1)............................................................................................................. 9
3.2.4Programme configuration............................................................................................................. 9
3.2.5Time MANAGER ......................................................................................................................... 9
3.2.6Pushbuttons – LEDs and LCD display........................................................................................ 10
4TC3......................................................................................................................................................... 13
4.1GENERAL CHARACTERISTICS...................................................................................................... 13
4.1.1General characteristics WM....................................................................................................... 13
4.1.2General characteristics WD ....................................................................................................... 14
4.2CONTROL PANEL........................................................................................................................... 15
4.2.1Styling TC3 (TIME MANAGER).................................................................................................. 15
4.2.1.1Control panel configuration................................................................................................. 16
4.2.1.2Programme selector (S1).................................................................................................... 16
4.2.1.3Programme configuration.................................................................................................... 16
4.2.1.4Pushbuttons and LEDs....................................................................................................... 17
4.2.1.5Time MANAGER ................................................................................................................ 19
4.2.1.6LCD display........................................................................................................................ 20
4.2.2Styling TC3 (PROPORTIONAL)................................................................................................. 21
4.2.2.1Control panel configuration................................................................................................. 22
4.2.2.2PROPORTIONAL............................................................................................................... 22
5TC2......................................................................................................................................................... 23
5.1GENERAL CHARACTERISTICS...................................................................................................... 23
5.1.1General characteristics WM....................................................................................................... 23
5.1.2General characteristics WD ....................................................................................................... 24
5.2CONTROL PANEL........................................................................................................................... 25
5.2.1Styling TC2 (TIME MANAGER).................................................................................................. 25
5.2.1.1Control panel configuration................................................................................................. 26
5.2.1.2Programme selector (S1).................................................................................................... 26
5.2.1.3Programme configuration.................................................................................................... 26
5.2.1.4Pushbuttons and LCD display............................................................................................. 27
5.2.1.5Time MANAGER ................................................................................................................ 28
5.2.1.6LCD display........................................................................................................................ 29
5.2.2Styling TC2 (PROPORTIONAL)................................................................................................. 30
5.2.2.1Control panel configuration................................................................................................. 30
6DEMO MODE SETTING.......................................................................................................................... 31
6.1Exiting DEMO mode......................................................................................................................... 31
7DIAGNOSTIC SYSTEM........................................................................................................................... 31
7.1Accessing diagnostics ...................................................................................................................... 31
7.2Quitting the diagnostics system ........................................................................................................ 31
7.3Diagnostic test phases...................................................................................................................... 32
8ALARMS................................................................................................................................................. 33
8.1Displaying the alarms to the user...................................................................................................... 33
8.2Reading the alarms .......................................................................................................................... 33
8.2.1Displaying the alarm.................................................................................................................. 34
8.2.2Example of alarm display........................................................................................................... 34
8.2.3Operation of alarms during the diagnostic cycle ......................................................................... 34
8.3Rapid reading of alarms.................................................................................................................... 35
8.4Deleting the last alarm...................................................................................................................... 35
9OPERATING TIME COUNTER................................................................................................................ 36
9.1Reading of operating time................................................................................................................. 36
9.2Display of total operating time........................................................................................................... 36
10WASHING PROGRAMMES AND OPTIONS........................................................................................ 37
10.1Possible programmes.................................................................................................................... 37
10.2Options (for EWM 21xx appliances with universal motor)............................................................... 38
10.3Options (for EWM 25xx appliances with asynchronous motor and inverter).................................... 40
10.3.1Compatibility between Options................................................................................................... 42
10.4Description of options.................................................................................................................... 43

SOI/DT 2010-03 dmm 4/78 599 72 84-41
11TECHNICAL CHARACTERISTICS....................................................................................................... 45
11.1Electronic control system memory................................................................................................. 45
11.1.1General structure of the memory system.................................................................................... 45
11.1.2FLASH ...................................................................................................................................... 45
11.1.3RAM.......................................................................................................................................... 46
11.2Door safety interlock ..................................................................................................................... 47
11.2.1Volumetric interlock with PTC.................................................................................................... 47
11.2.1.1Operating principle.............................................................................................................. 47
11.2.2Instantaneous door interlock...................................................................................................... 48
11.2.2.1Operating principle.............................................................................................................. 48
11.2.2.2Door open conditions.......................................................................................................... 48
11.2.2.3Automatic release device.................................................................................................... 48
11.3Water fill system............................................................................................................................ 49
11.3.1Flowmeter ................................................................................................................................. 49
11.3.2Operating principle of the flowmeter........................................................................................... 50
11.4Analogue pressure switch of water level control in the tub ............................................................. 51
11.5Drain pump................................................................................................................................... 52
11.6Circulation pump (where featured)................................................................................................. 52
11.7Heating......................................................................................................................................... 53
11.8Temperature sensor...................................................................................................................... 53
11.9Universal motor (EWM 21xx)......................................................................................................... 54
11.9.1Power supply to motor............................................................................................................... 54
11.10Three-phase asynchronous motor (EWM 25xx)............................................................................. 54
11.10.1Power supply to motor............................................................................................................ 54
11.11Anti-foam control system............................................................................................................... 55
11.12“FUCS”....................................................................................................................................... 56
12DRYING CIRCUIT ............................................................................................................................... 58
12.1Temperature control...................................................................................................................... 59
12.2Alarm Summary Table................................................................................................................... 60
13DIAGRAMS.......................................................................................................................................... 65
13.1WM diagram with UNIVERSAL MOTOR EWM 21xx...................................................................... 65
13.2WM diagram with THREE-PHASE ASYNCHRONOUS MOTOR EWM 25xx .................................. 67
13.3WD diagram with UNIVERSAL MOTOR EWM 21xx ...................................................................... 69
13.4WD diagram with THREE-PHASE ASYNCHRONOUS MOTOR EWM 25xx................................... 71
14ACCESS TO THE WM ELECTRONIC CONTROL SYSTEM (HC cabinet)............................................ 73
14.1Worktop........................................................................................................................................ 73
14.2Control panel ................................................................................................................................73
15ACCESS TO THE WM/WD ELECTRONIC CONTROL SYSTEM (NEXUS cabinet).............................. 76
15.1Worktop........................................................................................................................................ 76
15.2Control panel ................................................................................................................................76

SOI/DT 2010-03 dmm 5/78 599 72 84-41
1 Purpose of this manual
The purpose of this manual is to provide service engineers who are already familiar with the repair procedures for
traditional washing machines with information regarding washing machines fitted with the ENV06 electronic control
system.
Previous platforms (electronic/mechanical) used a safety pressure switch which controlled the minimum water
level in the tub, beneath which the supply to the heating element was interrupted.
The current electronic appliances manufactured (ENV06 platform) us a heating element with thermal fuses
(inside its branches) as safety, which interrupt if the water level drops below the minimum level permitted.
The incorporated NTC sensor contacts have step of 2.5 mm.
Do not remove/switch the NTC sensors between heating elements
The manual deals with the following topics:
•general characteristics
•control panel and washing programmes
•technical and functional characteristics
•access to the electronic control system
For detailed information concerning hydraulic circuits, structural characteristics of the appliances and
accessibility, please refer to the presentation Service Manual:
•Publication no. 599 37 47-13 for HEC washing machines
•Publication no. 599 70 40-15 for HEC RIM-ARCHED washer-dryers
Identification table between styling (TC2/3/4) and functionality (EWM 21xx/25xx)
EWM 21xx EWM 25xx
Styling Washing type Motor Washing type Motor
TC2 •Traditional with ECO-BALL
•Jet-System Universal •Traditional with ECO-BALL •Jet-System Three-phase
asynchronous
with Inverter
TC3 •Traditional with ECO-BALL
•Jet-System Universal •Traditional with ECO-BALL •Jet-System Three-phase
asynchronous
with Inverter
TC4 •Traditional with ECO-BALL
•Jet-System Universal •Traditional with ECO-BALL •Jet-System Three-phase
asynchronous
with Inverter
2 WARNINGS
Any work on electrical appliances must only be carried out by qualified
technicians.
Unplug the appliance before accessing internal components.
Before placing the appliance on its side, always empty all the water using the
purpose-provided system beside the drain filter.
Never place the appliance on its right side (electronic control system side): some
of the water in the detergent dispenser could leak onto the electrical components
and cause these to burn.
When replacing the heating element, replace it with one with the same
characteristics in order not to compromise the safety of the appliance
Removing the NTC sensor from the heating element is strictly prohibited.

SOI/DT 2010-03 dmm 6/78 599 72 84-41
3 TC4
3.1 GENERAL CHARACTERISTICS
The ENV06 electronic control system consists of a
single PCB, which incorporates the power, control and
display (where the LCD display is connected) functions.
The programme selector is incorporated in the board.
The PCB is mounted on a casing fitted to the control
panel.
3.1.1 General characteristics WM
Version
TC4
No. buttons maximum 5 (4 options + start/pause)
No. of LEDs maximum 14 + LCD display
Programme selector 15-21 positions with main switch (incorporated in the PCB)
Serial port DAAS-EAP communication protocol up to 115,200 baud
Power supply voltage 220/240V
50/60 Hz (configurable)
Washing type Traditional with "Eco-ball" sphere
Jet-System
Rinsing system Traditional with "Eco-ball" sphere
Jet-System
Motor Collector, with tachometric generator
Two-pole asynchronous, with three-phase tachometric generator (with
Inverter)
Spin speed 600 ÷1,600 rpm
Anti-unbalancing system FUCS (for universal motors)
AGS (for asynchronous motors with Inverter)
Water fill 1 solenoid valve with 1 inlet – 2 or 3 outlets
Detergent dispenser 3 compartments: pre-wash/stains, wash, conditioner
4 compartments: pre-wash, wash, conditioner, (bleach)
Control of water level in the
tub Electronic/analogue pressure switch
Door safety interlock Traditional (with PTC)
Instantaneous
Heating element heat output 1950W with thermal fuses incorporated
Temperature control NTC sensor incorporated in the heating element
Buzzer Traditional incorporated in the PCB
Sensors Water fill gauge (flowmeter)
Aqua control

SOI/DT 2010-03 dmm 7/78 599 72 84-41
3.1.2 General characteristics WD
Version
TC4
No. buttons maximum 5 (4 options + 1 start/pause)
No. of LEDs maximum 14 + LCD display
Programme selector 15-21 positions with main switch (incorporated in the PCB)
Serial port DAAS-EAP communication protocol up to 115,200 baud
Power supply voltage 220/240V
50/60 Hz (configurable)
Washing type Traditional with "Eco-ball" sphere
Jet-System
Rinsing system Traditional with "Eco-ball" sphere
Jet-System
Motor Collector, with tachometric generator (Universal)
Two-pole asynchronous, with three-phase tachometric generator
(with Inverter)
Spin speed 600 ÷1,600 rpm
Anti-unbalancing system FUCS (for universal motors)
AGS (for asynchronous motors with Inverter)
Water fill 1 solenoid valve with 1 inlet – 2 or 3 outlets
Detergent dispenser 3 compartments: pre-wash/stains, wash, conditioner
4 compartments: pre-wash, wash, conditioner, (bleach)
Control of water level in the
tub Electronic/analogue pressure switch
Door safety interlock Traditional (with PTC)
Instantaneous
Heating element heat output,
washing 1950W with thermal fuses incorporated
Heating element heat output,
drying 1840W (920+920)
Temperature control,
washing NTC sensor incorporated in the heating element
Temperature control, drying NTC probe
Thermostats
Buzzer Traditional incorporated in the PCB
Sensors Water fill gauge (flowmeter)
Aqua control

SOI/DT 2010-03 dmm 8/78 599 72 84-41
3.2 CONTROL PANEL
3.2.1 Styling TC4 WM/WD
•max. 5 buttons
•15 or 21-position programme selector
•14 LEDs
•LCD display
•Positioning of LEDs and buttons

SOI/DT 2010-03 dmm 9/78 599 72 84-41
3.2.2 Configuration of WM/WD control panel
The washing programmes, the functions of the selector knob (where featured) and the various buttons
vary according tot he model, since these are determined by the configuration of the appliance.
3.2.3 Programme selector (S1)
The selector features 15-21 positions and incorporates the ON/OFF
switch. The various positions of the selector may be configured to
perform different washing programmes (e.g.: water level, drum
movement, no. of rinses and the washing temperature to be selected
according to the type of garments). It can be turned both clockwise and
anti-clockwise.
In the first position, the appliance is switched off and the current
programme is cancelled.
For each programme, the compatible options and other parameters are
defined.
3.2.4 Programme configuration
The table below lists the parameters that can be used to define the washing programmes.
Types of fabric Cotton/linen, Synthetic fabrics, Delicates, Wool, Hand-wash,
Shoes, Jeans, Duvet, Silk.
Special programmes Soak, Miniprogramme, Easy-Iron, Conditioner, Rinses, Delicate
rinses, Drain, Delicate spin, Spin, Drying.
Temperature Normal, Maximum: the initial temperature is the maximum that
can be selected for a specific washing programme
Spin Normal, Minimum, Maximum
Options (Normal/Possible) Rinse Hold, Night cycle, Pre-wash, Stains, Bleach, Extra rinse,
Easy-Iron, Economy (energy label), Intensive, Normal, Daily,
Light, Quick, Super quick, Reduced spin speed, No spin, Half-
load.
Programme phases Pre-wash, Wash, Rinses, Spin, Delayed start, Drying.
3.2.5 Time MANAGER
The “Time manager” is designed to modify the programme settings according to the type of dirt; in order to
reduce or prolong the wash time. It is shown by the Display.
The reduction levels are provided in the following table:
COTTON SYNTHETICS DELICATES
Programme (base) Programme (base) Programme (base)
Daily Daily Daily
Light Light Light
Super Quick Super Quick Super Quick

SOI/DT 2010-03 dmm 10/78 599 72 84-41
Press button P2 in sequence to choose one of the three levels. The corresponding LED will light up to confirm
the selection.
L8 Daily
L7 Light
L6 Super Quick
The different washing options such as: Pre-wash, Economy, etc. are set compulsorily as a programme.
3.2.6 Pushbuttons – LEDs and LCD display
The functions of each button are defined by the configuration of the appliance.
•Button no. 1: this button is related to LEDs (L1÷L5). Pressing it
sequentially the spin speed varies from max., to no spin or rinse hold.
•Button no. 2: this button is configurable and is related to LEDs
(L6÷L8). (In some appliances it is connected to the “Time manager”)
•Button no. 3: this button is configurable and is related to LED (L14); it
performs the super rinse function.
•Button no. 4: this button is configurable and has the function of
START/PAUSE (inside there are two LEDs, one red that flashes in
the event of an alarm and one green that flashes when the appliance
is in pause mode or in combination with the red one to indicate the
alarm code).
•Button no. 5: this button is configurable and has the function of
DELAYED START. During the programme selection phase, a delayed
start can be selected, from 30’ to 20 hours (30’ "60’ "90’ "2h
"3h… "20h "0h) and the time is shown on the LCD display.
During the last hour, the time decreases minute by minute.
In the washer-dryers, push this button to set the drying time
displayed on the LCD display. Each time it is pressed, the time
increases by five minutes (from a minimum of 10 minutes to a
maximum of 130 minutes)

SOI/DT 2010-03 dmm 11/78 599 72 84-41
•wash phase indicator LEDs:
LEDs L13, L12, L16 are configurable and are used as indicators of the wash phases.
Possible indications
Pre-wash Lights during selection mode if the programme includes the pre-wash phase
and during the performance of the pre-wash
Wash Lights during selection mode if the programme includes the wash phase and
during the performance of the wash
Pre-wash/Wash Lights during selection mode if the programme includes the pre-wash or wash
phase and during the performance of these phases
Rinses Lights during selection mode if the programme includes rinse phases and
during the performance of the rinses
Spin Lights during selection mode if the programme includes the spin phase and
during the performance of the spin
Rinses / Spin Lights during selection mode if the programme includes rinses and spin and
during the performance of these phases
Drain Lights during selection mode if the programme includes the drain phase only
and during the performance of the drain
Extra rinse Lights when this option has been memorised (if included in the cycle)
Rinse hold Lights if the programme includes the rinse-hold option and at the end of the
cycle, when the appliance stops with water in the tub.
Cycle in progress Lights during the performance of the cycle
End of cycle Lights when the programme has been completed and the door has been
released
Door locked Lights when the safety device stops the door opening and switches off when it
is possible to open it.
Flashes when the device is about to unlock the door (with door interlock with
PTC, which needs one or two minutes to open)
Child lock Lights when the child safety is on and all buttons are deactivated
Drying Lights during selection mode if the programme includes the drying phase and
during the performance of this phase.
•LCD
The following information appears on the LCD display:
ªthe duration of the washing programme, which appears after it has
been selected. This time corresponds to that necessary for the
maximum wash load for each type of programme. After the programme
has started, the time decreases (and is updated) minute by minute.
ª-the duration of the drying time.
ª- the end of the programme is indicated by three flashing zeros
(when the door can be opened).
ªThe stopping of the appliance with water in the tub, after the
programmes with the RINSE HOLD option, is displayed by three
flashing zeros, the LED that indicates the door remains lit and the
LED of the START/PAUSE button switches off.
ªthe delayed start, selected on the related button. After the
START/PAUSE button is pressed, the countdown starts and the delay
time decreases hour by hour. In the last 2 hours, it decreases by 30
mins at a time.
ª- The thermometer: it is always on during the cycle and the icon is
animated during the heating phase.

SOI/DT 2010-03 dmm 12/78 599 72 84-41
ª- The padlock: when it is lit, it indicates that all the buttons are
disabled to prevent children from modifying, starting or pausing the
cycle.
To enable/disable this function, a key combination needs to be
pressed.
ª- Wrong choice of an option is displayed by <<Err>>, when a
function not compatible with the chosen programme is selected.
The wrong selection is also signalled by an acoustic alarm.
ª- An alarm code indicates an error in the appliance operation;
simultaneously to the displaying of the code, the START/PAUSE button
flashes.
•Buzzer (configurable)
The buzzer emits:
→A “beep”when the programmes or an option are selected, when the START/PAUSE button is pressed to
start or pause the cycle.
→Three “beeps”when an option not compatible with the selected programme is chosen, or when a button is
pressed or a knob turned during a cycle.
→A particular sequence of “beeps”for a two-minute duration when the cycle has terminated.
→A particular sequence of three “beeps”to signal an appliance malfunction.
To enable/disable the buzzer during the programme or option selection, see the key-combination described in
the instruction manual.

SOI/DT 2010-03 dmm 13/78 599 72 84-41
4 TC3
4.1 GENERAL CHARACTERISTICS
The ENV06 electronic control system consists of a single
PCB, which incorporates the power, control and display
functions where the LCD display is connected and the
programme selector is incorporated in the board.
The PCB is mounted on a casing fitted to the control panel.
4.1.1 General characteristics WM
Version
TC3
(TIME MANAGER)
Version
TC3
(PROPORTIONAL)
No. buttons maximum 8 (5 options + 1 start/pause + 2 for time driven)
No. of LEDs maximum 18 + LCD display
Programme selector 15-21 positions with main switch (incorporated in the PCB)
Serial port DAAS-EAP communication protocol up to 115,200 baud
Power supply voltage 220/240V
50/60 Hz (configurable)
Washing type Traditional with "Eco-ball" sphere
Jet-System
Rinsing system Traditional with "Eco-ball" sphere
Jet-System
Motor Collector, with tachometric generator (Universal)
Two-pole asynchronous, with three-phase tachometric generator (with
Inverter)
Spin speed 600 ÷1,600 rpm
Anti-unbalancing system FUCS (for universal motors)
AGS (for asynchronous motors with Inverter)
Water fill 1 solenoid valve with 1 inlet – 2 or 3 outlets
Detergent dispenser 3 compartments: pre-wash/stains, wash, conditioner
4 compartments: pre-wash, wash, conditioner, (bleach)
Control of water level in the
tub Electronic/analogue pressure switch
Door safety interlock Traditional (with PTC)
Instantaneous
Heating element heat output 1950W with thermal fuses incorporated
Temperature control NTC sensor incorporated in the heating element
Buzzer Traditional incorporated in the PCB
Sensors Water fill gauge (flowmeter)
Aqua control

SOI/DT 2010-03 dmm 14/78 599 72 84-41
4.1.2 General characteristics WD
Version
TC3
(TIME MANAGER)
Version
TC3
(PROPORTIONAL)
No. buttons maximum 8 (5 options + 1 start/pause + 2 for time driven)
No. of LEDs maximum 18 + LCD display
Programme selector 15-21 positions with main switch (incorporated in the PCB)
Serial port DAAS-EAP communication protocol up to 115,200 baud
Power supply voltage 220/240V
50/60 Hz (configurable)
Washing type Traditional with "Eco-ball" sphere
Jet-System
Rinsing system Traditional with "Eco-ball" sphere
Jet-System
Motor Collector, with tachometric generator (Universal)
Two-pole asynchronous, with three-phase tachometric generator
(with Inverter)
Spin speed 600 ÷1,600 rpm
Anti-unbalancing system FUCS (for universal motors)
AGS (for asynchronous motors with Inverter)
Water fill 1 solenoid valve with 1 inlet – 2 or 3 outlets
Detergent dispenser 3 compartments: pre-wash/stains, wash, conditioner
4 compartments: pre-wash, wash, conditioner, (bleach)
Control of water level in the
tub Electronic/analogue pressure switch
Door safety interlock Traditional (with PTC)
Instantaneous
Heating element heat output,
washing 1950W with thermal fuses incorporated
Heating element heat output,
drying 1840W (920+920)
Temperature control,
washing NTC sensor incorporated in the heating element
Temperature control, drying NTC probe
Thermostats
Buzzer Traditional incorporated in the PCB
Sensors Water fill gauge (flowmeter)
Aqua control

SOI/DT 2010-03 dmm 15/78 599 72 84-41
4.2 CONTROL PANEL
4.2.1 Styling TC3 (TIME MANAGER)
•max. 8 buttons
•15 or 21-position programme selector
•18 LEDs
•LCD display
Version WM
Version WD
•Positioning of LEDs and buttons

SOI/DT 2010-03 dmm 16/78 599 72 84-41
4.2.1.1 Control panel configuration
WM WD
The washing programmes, the functions of the selector knob (where featured) and the various buttons
vary according tot he model, since these are determined by the configuration of the appliance.
4.2.1.2 Programme selector (S1)
The selector features 15-21 positions and incorporates the ON/OFF switch.
The various positions of the selector may be configured to perform different
washing programmes (e.g.: water level, drum movement, no. of rinses and the
washing temperature to be selected according to the type of garments). It can
be turned both clockwise and anti-clockwise.
In the first position, the appliance is switched off and the current programme is
cancelled.
For each programme, the compatible options and other parameters are
defined.
4.2.1.3 Programme configuration
The table below lists the parameters that can be used to define the washing programmes.
Types of fabric Cotton/linen, Synthetic fabrics, Delicates, Wool, Hand-wash,
Shoes, Jeans, Duvet, Silk.
Special programmes Soak, Miniprogramme, Easy-Iron, Conditioner, Rinses, Delicate
rinses, Drain, Delicate spin, Spin. Drying.
Temperature Normal, Maximum: the initial temperature is the maximum that
can be selected for a specific washing programme
Spin Normal, Minimum, Maximum
Options (Normal/Possible) Rinse Hold, Night cycle, Pre-wash, Stains, Bleach, Extra rinse,
Easy-Iron, Economy (energy label), Intensive, Normal, Daily,
Light, Quick, Super quick, Reduced spin speed, No spin, Half-
load.
Programme phases Pre-wash, Wash, Rinses, Spin, Delayed start, Drying.

SOI/DT 2010-03 dmm 17/78 599 72 84-41
4.2.1.4 Pushbuttons and LEDs
The functions of each button are defined by the configuration of the appliance.
•Button no. 1: this button is configurable and is related to LEDs (DL16÷DL5).
Depending on the configuration of the appliance, it can be connected both to
the temperature regulation and the spin speed regulation. Press it in sequence
to choose your desired regulation.
Depending on the configuration of the appliance, different combinations can
be obtained. The tables below contain some examples of combinations
between temperature and spin
•Button no. 2: this button is configurable and is related to LEDs
(DL6÷DL10).
The description of its functions is the same as the one for pushbutton 1.
•Button no. 3: this button is configurable and is related to LED (DL11), in
washing machines. Depending on the configuration of the appliance, it can
perform the function of:
Normal, daily, light, quick, super quick, intensive, economy, pre-wash, easy-
iron, bleach, stains, super rinse, night cycle, rinse hold, half-load, reduced spin
speed, no spin.
In washer-dryers, it is related to LEDs (DL11÷DL13) and performs the function
of automatic drying at three levels:
- Extra
- Wardrobe
- Iron.
•Button no. 4: this button is configurable and is related to LED (DL14).
In washing machines, it can perform the function of:
Normal, daily, light, quick, super quick, intensive, economy, pre-wash, easy-
iron, bleach, stains, super rinse, night cycle, rinse hold, half-load, reduced spin
speed, no spin.
In washer-dryers, it performs the function of:
Time-drying
LEDs Temperature
DL5 90° 90°
DL4 60° 60°
DL3 40° 50°
DL2 30° 40°
DL1 0° 30°
LEDs Spin
DL5 1200 1400
DL4 900 900
DL3 700 700
DL2 Night cycle Night cycle
DL1 Rinse hold Rinse hold

SOI/DT 2010-03 dmm 18/78 599 72 84-41
•Button no. 5: this button is configurable and is related to LED (DL15);
depending on the configuration of the appliance, it can perform the function of:
Normal, daily, light, quick, super quick, intensive, economy, pre-wash, easy-
iron, bleach, stains, super rinse, night cycle, rinse hold, half-load, reduced spin
speed, no spin.
It can also perform the function of delayed start.
•Button no. 6: this button is configurable and has the function of
START/PAUSE (inside there are two LEDs, one red that flashes in
the event of an alarm and one green that flashes when the
appliance is in pause mode or in combination with the red one to
indicate the alarm code).
•DL16 Door locked: Lights when the safety device stops the door
opening and switches off when it is possible to open it. It flashes
when the device is about to unlock the door (with door interlock
with PTC, which needs one or two minutes to open).

SOI/DT 2010-03 dmm 19/78 599 72 84-41
4.2.1.5 Time MANAGER
The “Time MANAGER” is used with the COTTON, SYNTHETICS and DELICATES programmes.
It is split into:
“Time MANAGER 1” and “Time MANAGER2”
The difference between the two versions can be seen in the number of sectors in the T-shirt (there are more for
the “Time MANAGER2”).
Both versions have the main function of: modifying the washing time of the programme set.
This variation in the washing time can be obtained by pressing buttons P7 and P8, the sectors of the T-shirt
vary in brightness and at the same time the three digits display the washing time.
Below is a graphic of the LCD display (for both versions) after the COTTON programme has been selected, as
an example.
Time MANAGER 1 Time MANAGER2
The differences between the two versions of “Time MANAGER”
Time MANAGER 1 Time MANAGER2
Super Refresh (*) ------------------------
Refresh(*) ------------------------
Super Quick
(super rapid cycle) recommended for
cottons and synthetics with light dirt
level, and for half load
Quick
(rapid cycle) recommended for clothes
used just once
Light
(light cycle) recommended for slightly
dirty clothes or of daily use
Daily
(daily cycle) recommended for quite
dirty clothes.
Normal
(normal cycle) recommended for quite
dirty clothes worn many times
Intensive
(intensive cycle) recommended for very
dirty clothes which need stain removal
treatments, soaking or pre-wash
(*) When this programme is selected, the T-shirt icon may flash several times and then stop.

SOI/DT 2010-03 dmm 20/78 599 72 84-41
The options for the “Time MANAGER” are summarised in the following tables:
Time Manager 1
COTTONS SYNTHETICS DELICATES
INTENSIVE ------------- -------------
NORMAL (basic programme) NORMAL (basic programme) NORMAL (basic programme)
DAILY DAILY DAILY
LIGHT LIGHT LIGHT
QUICK ------------- -------------
SUPER QUICK SUPER QUICK SUPER QUICK
Time Manager 2
COTTONS SYNTHETICS DELICATES
INTENSIVE INTENSIVE INTENSIVE
NORMAL (basic programme) NORMAL (basic programme) NORMAL (basic programme)
DAILY DAILY DAILY
LIGHT LIGHT LIGHT
QUICK QUICK QUICK
SUPER QUICK SUPER QUICK SUPER QUICK
REFRESH REFRESH REFRESH
SUPER REFRESH SUPER REFRESH SUPER REFRESH
4.2.1.6 LCD display
The following information appears on the LCD display:
The three digits with seven segments represent:
ªDuration of the washing and drying programme
ªEnd of the programme
ªDelayed start
ªWrong choice of an option
ªAlarm code
ªDuration of drying time
For explanations, please refer to the LCD display description on pages 11 and 12
ªThermometer
See page 11
(represented as a symbol in washing machines, not represented in washer-dryers)
ªPadlock
See page 12
ªWashing phases
(for both washing machines and washer-dryers)
Washing, rinses, drain and spin light up in the selection mode if the
programme includes these phases and during the performance of the phase.
ªDrying phase
Lights during selection mode if the programme includes the drying phase
and during the performance of the phase.
•Buzzer
See page 12