Electronics Line EL-2614 User manual

EL-2614
 English
The EL-2614 is a four-button keyfob transmitter designed for use
with Electronics Line 3000 s supervised wireless range of
receivers.
Registration
To register the EL-2614:
1. Set the receiver to Registration mode.
2. Press one of the buttons, making sure that the LED lights
up when the button is pressed.
3. Wait for five seconds and press the same button again.
Alternatively, the EL-2614 can be registered to the receiver by
manually entering the transmitter's serial number.
Battery Replacement
If the LED blinks during transmissions, this
indicates that the batteries are low and need
replacing.
To replace the batteries:
1. Insert a small screwdriver into the pry-off
slot – see Figure 2. Carefully twist the
screwdriver to separate the front and
back of the casing.
2. Observing correct polarity, replace the
batteries.
3. Close the casing making sure that the
front and back click shut.
Technical Specifications
Antenna: Built-in whip
Frequency: 868.35, 433.92 or 418MHz FM
Power: 2 x 3V Lithium Battery, Size CR1225
Current Consumption:
16mA (transmission),
2µA (standby)
RFI Immunity: 40V/m
Operating Temperature: 0 - 60°C
Dimensions: 62 x 42 x 15mm
Figure 1: EL-2614/
Figure 1: EL-2614/
Figura 1: EL-2614
Figure 3: EL-2614 Rear view (casing open)/
Figure 3: EL-2614 Vue arri re (boîtier ouvert)/
Figura 3: EL-2614 Vista posterior (tapa abierta)
Figure 2: Opening the casing/
Figure 2: Ouverture du boîtier/
Figura 2: Abriendo la tapa
Battery Holders/
Emplacement
des Batteries/
Soporte de la
Batería

ZI0241F (3/04)
All data is subject to change without prior notice. In no event shall Electronics Line 3000 Ltd. (EL3K) be liable for an amount in excess of EL3K. s original
selling price of this product, for any loss or damage whether direct, indirect, incidental, consequential or otherwise arising out of any failure of the product.
Hereby, Electronics Line 3000 Ltd. declares that this transmitter is in compliance with the essential requirements and other relevant provisions of Directive
1999/5/EC.
Electronics Line 3000 Ltd.: 2 Granit Street, Kiryat Arieh, POB 3253, Petah Tikvah 49130 Israel. Tel: [phone], Fax: (972-3)
922-0831
99
USA: 5637 Arapahoe Avenue, Boulder, Colorado 80303. Tel: [phone], Fax: [phone]
55
UK: Unit 7, Leviss Trading
Estate, Station Road, Stechford, Birmingham B33 9AE. Tel: [phone], Fax: [phone]France: ZI-61, rue du Marché
Rollay, 94500 Champigny-Sur-Marne. Tel: [phone], Fax: [phone]
RR
ZI0239C (3/04)
All data is subject to change without prior notice. In no event shall Electronics Line 3000 Ltd. (EL3K) be liable for an amount in excess of EL3K. s original
selling price of this product, for any loss or damage whether direct, indirect, incidental, consequential or otherwise arising out of any failure of the product.
Hereby, Electronics Line 3000 Ltd. declares that this transmitter is in compliance with the essential requirements and other relevant provisions of Directive
1999/5/EC.
EL-2614
 Français
Le EL-2614 est un émetteur de
télécommande à quatre boutons à utiliser
avec la gamme des récepteurs de radio
supervisés d Electronics Line 3000.
Processus d’Enregistrement
1. Réglez le récepteur en mode
Enregistrer.
2. Appuyez sur un bouton, vérifiez que la
LED de la télécommande s allume
lorsque le bouton est appuyé.
3. Attendez pendant cinq secondes et
appuyez à nouveau sur le même
bouton.
Indication de Batterie à Basse Tension
Si la LED clignote lors des transmissions, cela
signifie que la tension des batteries est basse et
qu elles doivent être remplacer:
Pour remplacer les batteries:
1. Insérez un petit tournevis dans la fente
– voir Figure 2. Tournez doucement le
tournevis pour séparer l avant et l arrière
du boîtier.
2. En observant la polarité
correcte, remplacez les batteries.
3. Fermez le boîtier en vérifiant à
ce que l avant et l arrière se ferment avec
un clic.
Spécifications Techniques
Antenne: Fouet intégré
Fréquences: 868.35, 433.92 ou 418MHz FM
Alimentation:
2 x 3V Batterie de lithium, Taille CR1225
Consommation du courant:
16mA (en transmission), 2µA (au repos)
Immunité IRF: 40V/m
Température de Fonctionnement: 0-60°C
Dimensions: 62 x 42 x 15mm
 Español
El EL-2614 es un transmisor de cuatro
botones diseñado para ser utilizado con la
línea de receptores inalámbricos supervisada
de Electronics Line 3000.
Procedimiento de Registración
1. Coloque el receptor en modo
Registración.
2. Presione un botón, asegurándose que el
LED del llavero encienda al ser
presionado.
3. Aguarde cinco segundos y presione el
botón nuevamente.
Indicación de Ba a Batería
Cuando el LED destella durante la transmisión,
las baterías están bajas y precisan ser
reemplazadas.
Para reemplazar las baterías:
1. Inserte un pequeño destornillador en la
ranura inferior – ver Figura 2.
Cuidadosamente gire el destornillador
para separar las tapas.
2. Observando la polaridad
correcta, reemplace las baterías.
3. Cierre el llavero asegurándose que las
tapas coincidan correctamente.
Especificaciones Técnicas
Antena: Incorporada, de Lazo Interno
Frecuencia: 868.35, 433.92 o 418MHz FM
Alimentación: 2 x 3V Batería de Litio, CR1225
Consumo de Corriente:
16mA (transmisión), 2µA
(en reposo)
Inmunidad a RF: 40V/m
Temperatura de Operación: 0-60°C
Dimensiones: 62 x 42 x 15mm