ABB 2CSYD0301N Parts list manual

1
2CSYD0301N
1 GENERAL DESCRIPTION
The Remote control is a portable device that enables to interact with
the control unit.
It encompasses 5 keys that can be configured and linked to the
functions related to the arming and disarming of the anti-intrusion
areas or to special functions such as burglary alarm, panic alarm, aid
alarm, operations or system status request.
The Braille characters enable an easy usage of the device also by
visually impaired people.
Through the configurable LEDs, it is possible to know the status of
the areas.
2 ACQUISITION AND
PROGRAMMING
To let the control unit acquire the remote control:
1. Power the remote control by removing the isolating
protection of the battery (please refer to the section Battery
replacement for details about how to open the remote
control).
2. On the control unit, activate the remote control acquisition
mode.
3. Press any key on the remote control so that it can be
acquired by the control unit.
4. Program the remote control (keys and LEDs).
Programming details are encompassed in the control unit installation
manual.
3 USAGE
IMPORTANT NOTE!As keys and LEDs (except LED 1) are
freely configurable, the function linked to each of them shall be
communicated to the user by the installer.
Each remote control can be configured in a different way.
When you press a key, the remote control sends the relevant
command to the control unit.
LED 1 indicates if the control unit replied.
3.1 LEDs
LED 1 is a standard LED and cannot be configured. Signals provided
by LED 1 when any key is pressed are the following:
LED turns on green:
Full battery
LED turns on red:
Voltage of the battery lower than 2.7 V
LED turns on after 1 sec:
The control unit does not reply
LED turns on after 0.2 sec:
The control unit replied
LEDs 2, 3, 4 and 5 can be separately configured and provide the
following indications:
LED turned off:
The LED is not configured
LED turns on green for 2
seconds:
Anti-intrusion area/s disarmed
LED turns on red for 2
seconds:
Anti-intrusion area/s armed
All LEDs turn on orange for 2
seconds:
Arming/disarming block on the control
unit
When you receive an arming block signal, it is possible to force the
block by sending the command again.
2
CSYD0301N
Remote control
EN
Usage manual

2
2CSYD0301N
4
MAINTENANCE
4.1
Cleaning
To clean the device
, use a soft and dry cloth. Do not use liquids or
abrasive products
.
4.2
Battery replacement
To replace the battery
:
1. Open the battery compartment by rotating the cover
counter-clock-wise.
2. Extract the exhausted battery.
3. Insert the new battery by paying attention to the polarities.
4. Close the battery compartment.
WARNING!The exhausted battery is a special waste and it
shall be disposed according to the regulations in force.
4.3 Reset
WARNING! The reset procedure shall be carried out when
required and only by the installer and not by the user.
To delete the acquisition address and to restore the factory
configuration of the remote control, delete the remote control on the
control unit, remove and re-insert the battery by following the points
1÷4 in the section 4.2.
5
TECHNICAL SPECIFICATIONS
APPLICATION SCOPE
Security
COMMUNICATION
TECHNOLOGY
Transmission in FM 868.3 MHz
RANGE IN FREE AIR
100 m
POWER SUPPLY
no. 1 Lithium battery CR2032 3
V
COMMAND ELEMENTS
5 keys
SIGNAL ELEMENTS
5 LEDs: red/green/orange
Low battery
Additional
data provided by the manufacturer
USAGE TEMPERATURE
-5 … + 55 °C
USAGE RELATIVE HUMIDITY
Max 93% max (non-condensing)
USAGE ENVIRONMENT
Indoor/Outdoor
SIZES (L x H x w)
78 x 40 x 10 mm
Package contents
n
o. 1 Remote control
n
o. 1 Lithium battery CR2032 3 V (not connected)
n
o. 1 Manual
WARNING! Installation must be carried out only by a
qualified electrician
.
EC Declaration of Conformity
ABB S.p.A.,
with registered office in Milan - via Vittor Pisani 16,
declares under its own responsibility that the device with product
code
2CSYD0301N
meets the essential electromagnetic compatibility
and security requirements contained in the Directive R&TTE
1999/5/EC and
in the EC Low Voltage Directive 2006/95/CE, as it
was designed and manufactured in compliance with the following
harmonized standards
: EN 300 220, EN 50131-1, EN 50131-5-3.
ABB S.p.A. –
An
ABB SACE
Division
Viale
dell’Industria, 18
20010 Vittuone (MI)
Printed in Italy
For further information and
assistance
:
from Monday to Saturday
from 8:00 a.m. to 7:00 p.m.
Manual code 2CSM600508D0201 rev 00