Electrovision Eagle G009MH User manual

G009MH
Eagle Set of 6 RGB LED Puck Lights
with PSU + Remote Control

CONGRATULATIONS ON YOUR PURCHASE
Thank you for purchasing this Eagle Puck Light Kit. Please read these instructions carefully
and leave with the user of the product for future reference. If the product is sold on then the
instruction/manual should pass on as well.
BEFORE USE
You must inspect the product and all accessories including any cables or leads for any signs
of damage. If the product is damaged, DO NOT use it, and contact your supplier immediately.
PRODUCT SAFETY
• Children shall not play with the unit.
• Cleaning and user maintenance shall not be made by children without supervision.
• Please ensure device is switched off when not in use.
• Do not use the device for other than its intended use.
• Please ensure the product is not stored in a hot or humid location.
• Do not use this product in bathrooms or other very hot humid locations.
• Periodically check this product and its power supply for damage. If any is detected do not
use and contact your supplier.
• Do not leave this product on unattended.
• The power supply MUST be kept in a well-ventilated area away from sources of heat and
moisture such as cookers and kettles
INCLUDED IN THE BOX
1 x 6 puck lights 12 x Wood screws 1 x Controller
6 x Sticky pads 1 x Remote Control
INFORMATION
• Plan your installation before fitting
• Maximum lead length from puck to puck is 0.5m
• While the product comes with both doubled sided sticky foam pads and wood screws in
most circumstances the pads on their own will usually be sufficent for permanent fixing.
before using the wood screws
the installer should take care to make sure they are suitable for the location.
• When using the sticky pads for installation ensure all surfaces are clean and clear of
grease and dust.
INSTALLATION
Fix each puck in place using either the sticky foam pads or wood screws. If using the screws
only use the two outer fixing points on the puck as per the image below. Access to these can
be gained by unscrewing the top of the puck and removing the plastic diffuser. This should be
replaced after installation. The pucks connect via a plastic 4 pin connector on the end of the
attached leads.
Each puck connects to each other by connecting the leads together on the pucks. Image
above - ensure when connecting, the arrows on each connection line up.
When all the pucks have been installed connect the power supply to the lead puck and switch
on.

CONTROL
The product can be controlled via the separate remote control.
MAINTENANCE
There are no user serviceable parts in this product. Periodically check the product for LED
failure and damage. If any of the LED’s have failed or the product is damaged in anyway
switch off and disconnect from the mains supply. To clean the product, switch off and
disconnect from the mains supply. Using a slightly damp cloth gently wipe over. Do not
use bleach, solvent based cleaners or strong detergents. These may damage the product and
invalidate the warranty. If the mains lead is damaged, it must be replaced by the manufacturer
or and authorised service centre.
PAT TESTING
When used in an office environment, we recommend that this product should be safety-tested
yearly by a qualified electrician (PAT Tested). We recommend that it is PAT tested regularly
when used in a domestic environment.
GENERAL SAFETY REQUIREMENTS
Domestic wiring must be tested periodically by a qualified electrician at least once every 10
years or at every change of occupancy. For office and retail premises, and buildings such as
village halls, the wiring must be inspected at least once every 5 years. It is recommended that
all building be fitted with smoke alarms (it is mandatory for new buildings)
TECHNICAL SPECIFICATION
Power Input ..................................................................................................................DC12V 1.5A
Puck Dims...............................................................................................................60x60x8mm x 6
Illumination ................................................................................................................................LED
Controller ...........................................................................................................IR Battery CR2025
SERVICE WARRANTY
Electrovision Ltd. guarantees the product free from defects in materials and workmanship for
a period of twelve months. Should this product be operated under conditions other than those
recommended, or any attempts are made to service or modify the product, then the warranty
will be rendered void. The product you buy may sometimes dier slightly from illustrations.
This warranty is in addition to, and does not aect, your statutory rights. Our guarantee is
administered by our retailers. If your product arrives damaged, you must contact the retailer
from whom you bought it. The retailer’s contact details will be on the invoice that arrived with the
product, or on the e-mail you received when you placed the order. Do not contact Electrovision,
only your retailer can arrange a replacement. If the product needs to be repaired or replaced, you
must contact the retailer from whom you bought it. If you have just received your product and
require technical help in using it, please call our Help Desk on [phone]
Electrovision Ltd, Lancots Lane, Sutton, St. Helens, Merseyside, WA9 3EX
www.electrovision.co.uk
R
ON
OFF
WRGB
FLASH
STROBE
FADE
SMOOTH
Brightness
White
Colour
Selection
Programs