Jandy Levolor K-1100 User manual

Levolor is the alternative choice of contractors over mechanical floats;
because it's trouble-free, easy to install and there are no moving parts.
LEVOLOR is a computer-controlled device that detects
a low water condition and automatically replaces the
water to a pre-set level. LEVELOR works well on new and existing
pools and spas. LEVOLOR can be used in any situation
where a consistent liquid level is desired (i.e., pools, spas,
aquariums, ponds, reservoirs, storage tanks,
water cooling towers, etc.).
Electronic Water Leveler
Model K-1100
PWR Sensor Filling
Electronic
Water Levelor
The nextgeneration
in automated controls.
SM
Millenium
System Dynamics
Scottsdale, AZ85260
800-844-8514
TM TM
TM
IMPORTANT SAFETY INSTRUCTIONS
1. READ AND FOLLOW ALL INSTRUCTIONS.
2. WARNING: To reduce the risk of injury, do not permit children to
use this product unless they are closely supervised at all times.
3. SAVE THESE INSTRUCTIONS.
4. Sensor wires must be continuous and not spliced.
Call factory with any questions: 1-800- 844-8514
5. Solder all low voltage wire connections when possible and always
use grease-filled wire nuts on low voltage connections.
Patented
High Voltage Compartment
No user service parts inside
Model No. K-1100
INSTALLATION INSTRUCTIONS
Page 1
Rev E © SDI 2006
LEVOLOR IS A REGISTERED TRADEMARK OF SYSTEM DYNAMICS

Pump
Time Clock
Return to Pool
Low Voltage Wire
Expansion Joint
Sensing Probe
Skimmer
Throat
Skimmer
Basket
Solenoid
Valve
Water
Supply
HOUSE
OR
IRRIGATION
SYSTEM
Filter
A 24VAC solenoid valve will provide water
from a supply line to the pool or spa. Installing
the supply line either before or after the filter
at the equipment pad is acceptable or a
dedicated line back to the pool. A 3/4 inch valve
is the minimum recommended, and of course,
an anti-siphon valve will provide inexpensive
insurance against accidental draining of the pool.
Always use an in-line strainer which can be
purchased from SDI (part# BR-Y).
Page 4
EXISTING INSTALLATION DIAGRAM
OPERATING
WATER LEVEL
1' - 0'
MIN.
INSTALL LINE LEVEL OR RUN UP-HILL
FROM POOL TO PREVENT AIR LOCK
OPERATING WATER LEVEL
6"
MIN.
EQUIP. RM
FLOOR LEVEL
FROM CITY
WATER SUPPLY
VIA DBL CHK VLV
115-220VAC 24VAC
11/2" TO RETURN LINE
2" STILLING LINE
LEVOLOR - ELECTRONIC WATER LEVELER
BY SYSTEM DYNAMICS, INC. (SDI)
1-800-844-8514 NEW CONSTRUCTION
POOL WATER
LEVELER SCHEMATIC
SOLENOID VALVE
(SDI Part #SOL-100)
GRATE COVERED WALL FITTING
OR 1/2" EYE-BALL FITTING
PWRSensorFilling
-220Electronic
WaterLevelor
SM
TMTM
Patented
ModelNo.K-1100
Parts supplied with S-2040. Sensor includes: Sensor w/50 ft. - 200 ft. of wire (do not splice wires)
Remote Sensor Housing (RSH).
DECK LID INSTALLATION METHOD DETAILS
When using the static pipe method
glue all fittings.
1" Coupling
SDI SENSOR
PART# S-2040
1" PVC CUT
TO LENGTH
1/2" CONDUIT CONNECTION
9" DECK LID
6"
2" STATIC LINE VENTED AT
THE TOP BY DRILLING A
HOLE INTO IT.
Conduit to
Sensor
Control System
at Control box
Terminate Sensor
at minimum
operating level
Desired
water level
2" Static Line
1" Coupling
INSTALLATION METHOD DETAIL
CUT 1" PVC
TO LENGTH
SDI SENSOR
PART# S-2040
1" PVC CUT
TO LENGTH
2" PVC
2" Minimum
Dimension
5 5/8"
2 3/4"
REMOTE SENSOR HOUSING DETAIL
2"
Rev E © SDI 2006
1" Brass "Y" strainer
SDI part# BR-Y
1" Brass "Y" strainer
SDI part# BR-Y
Monitoring
Computer