Elinchrom FIVE User manual

Elinchrom FIVE - April 2022
FIVE
Battery
Monolight

Table of contents
Introduction 4
FIVE characteristics 5
Before you start 7
General user and safety information 7
Display panel - Dashboard menu 16
Flash mode setup 17
Modelling lamp 18
Menu features 19
Replace a ashtube 22
Troubleshooting 23
Disposal and recycling 25
Technical data 26
Legal information 30
Declaration of conformity USA & Canada 32
FIVE
2— ELINCHROM FIVE User manual

Dear photographer,
Thank you for buying the Elinchrom FIVE Battery
Monolight ash unit. All Elinchrom products are
manufactured using the most advanced technology.
Carefully selected components are used to ensure the
highest quality and the equipment is submitted to
many tests both during and after manufacture. We
trust that it will give you many
years of reliable service.
Please read the instructions carefully before use, for
your safety and to obtain maximum benet from many
features.
Your Elinchrom Team

Introduction
This manual may show images of products with
accessories, which are not part of sets or single units.
Elinchrom set and single unit congurations may change
without advice and may differ in other countries.
Please nd actual congurations at www.elinchrom.com
For further details, upgrades, news and the latest
information about the Elinchrom System, please regularly
visit the Elinchrom website. The latest user guides
and technical specications can be downloaded in the
“Support” area.
Technical data, features and functions of Elinchrom
ash units, accessories and the Skyport system may
change without advice. The listed values can differ due
to tolerances in components, or measuring instruments.
Technical data, subject to change. No guarantee for
misprints.
Keep this user manual for later information and
reference.
4— ELINCHROM FIVE User manual

FIVE characteristics
The FIVE Battery Monolight unit offers Manual, Action,
HSS and TTL modes. The TTL (Through the Lens
Metering) mode allows you to access fully automatic
exposure setups according to your digital camera
capabilities. If you wish to work in the manual mode
or combine both modes, the unit enables you to save
the TTL exposure parameters as a starting point when
passing to the manual mode.
The unit supports Skyport radio remote control and HSS.
It offers fast ash durations at lower power levels.
Characteristics:
• 522 J/Ws maximum output power in Manual and TTL
modes.
• 7 f-stops power range.
• Action mode for optimised ash duration.
• Bi-color LED modelling lamp power in 40 adjustment
levels.
• HSS and TTL are supported on the Transmitter Pro,
with the latest rmware update.
• The dedicated Group colour is visible at the
illuminated Elinchrom side logos.
• Sync socket 3.5 mm and USB-C socket for recharging
& rmware updates
5— ELINCHROM FIVE User manual

• Internal WLAN for IoT module update and future
options.
• FIVE Li-Ion Battery. Capacity: 82.08Wh / DC 14.4V
Bluetooth®built-in for the Elinchrom Software/App
(available for iOS, Android, macOS and Windows).
• Elinchrom standard mount for accessories.
• 7/8 mm umbrella shaft.
• Ergonomic design with large LCD colour display.
Elinchrom TTL mode
• 7 f-stop ash power range.
• TTL +/- 3 f-stops adjustable in 1/3 steps.
• LED modelling lamp is adjustable in 40 power steps.
• Compatible with Canon, Nikon, Fujilm, Sony,
Olympus/Panasonic and Pentax.
Manual mode
• Compatible with all Skyport Transmitters.
• Flash power in 1/10 f-stop steps.
• Saves the TTL power as a starting point for the
manual mode.
6— ELINCHROM FIVE User manual

Before you start
GENERAL USER SAFETY INFORMATION
• Flash units are powerful light sources. Please be aware
of the danger, or inconvenience, that they may present
to some persons and children.
• Keep ash units out of reach of unauthorised persons
whenever possible.
• Keep ash units away from children!
• According to safety regulations, we draw your attention
to the fact that electronic ash units are not designed
for extreme outdoor use, in damp or dusty conditions
and should not be used after being exposed to sudden
temperature changes causing condensation. The
humidity protection class conforms to the norms of IP20.
• Do not use without permission in restricted areas (such
as hospitals, laboratories, etc.).
• Do not use near ammable / explosive material. Keep
minimum 1m or more distance to any object.
• Never ash into the eyes of a subject without warning.
Close use may affect eyesight.
• The ambient temperature whilst the unit is in use: -20°C
(-4°F) up to max. 35°C (95°F). Storage temperature:
15°C up to 25°C. Charging temperature: 0°C to 35°C
• There is high voltage and there can be high currents,
so please apply all the usual safety precautions when
handling the unit.
7— ELINCHROM FIVE User manual

• Do not turn on the device without a mounted and
working ashtube due to high voltage at the exposed
terminals!
• Flash systems store electrical energy in capacitors by
applying high voltage.
• The units may retain an internal charge for a
considerable time even though disconnected from
the battery. Internal defective charge capacitors may
explode whilst the unit is in use, so never switch on a
ash unit, once it has been found to be faulty.
• For your safety, never open or disassemble your
ashes. Only an authorised personnel should open or
attempt to repair this unit.
• Always switch off the ash unit before changing
accessories.
• The unit, the ashtube and accessories may become
very hot during and after use! To avoid injuries,
handle with an insulating cloth or wait until parts
have cooled down. Avoid direct sunlight, which
might heat up the ash unit and affect the photocell
efciency. Protect the ash unit when used in humid
conditions but ensure ventilation for cooling!
• Under no circumstances should any object be
inserted into the ventilation holes.
• Use only original Elinchrom Accessories. Damaged
cables, glass domes and cases must be immediately
replaced by customer service.
8— ELINCHROM FIVE User manual

BATTERY SAFETY AND CHARGING NOTICE
IMPORTANT! FOR YOUR SAFETY
Do not use the battery for a purpose other than those
specied!
• To recharge the FIVE battery we recommend using
the Elinchrom 65W USB-C Wall Charger. If the
recharging operation fails to complete even when a
specied recharging time has elapsed, immediately
stop further recharging and disconnect the charger.
• If the external battery gives off odors, generates heat,
or is deformed, or in any way appears abnormal
during use, recharging or storage, immediately
remove the Battery Charger and stop using it.
• Recharge the FIVE after using. Store the unit only
with a recharged battery!
• If the FIVE is not frequently used, recharge the unit
latest after three months to avoid damaging the Li-
Ion cells by deep discharging.
• Do not expose the unit to extreme heat, cold or
humidity to avoid damages.
DO NOT USE A FAULTY, APPARENTLY DAMAGED OR
DEFORMED BATTERY UNIT! ELECTRICAL, CHEMICAL
AND MECHANICAL HAZARDS
• Do not disassemble, open or modify the battery.
• Do not transport or store the battery together with
metal objects such as necklaces, hairpins, etc.
9— ELINCHROM FIVE User manual

• Do not pierce the battery with a nail or other sharp
objects, strike it with a hammer, or stand on it.
• Do not strike or throw the battery.
• If the battery leaks and electrolyte gets into the
eyes, do not rub them. Instead, rinse the eyes with
clean running water and immediately seek medical
attention. Otherwise, eye injury may result.
• Store the battery in a location where children cannot
reach it.
• Do not put the battery into a microwave oven or a
pressurized container.
WARNING: PHOTOSENSITIVITY / EPILEPSY / SEIZURES
A very small percentage of individuals may experience
epileptic seizures or blackouts when exposed to certain
light patterns or ashing lights. These conditions may
trigger previously undetected epileptic symptoms or
seizures in persons who have no history of prior seizures
or epilepsy. If you, or anyone in your family, has an
epileptic condition or has had seizures of any kind,
consult your physician before using the EL unit.
IMMEDIATELY DISCONTINUE use and consult your
physician before resuming use of your EL unit if you
or any person experience any of the following health
problems or symptoms:
• Dizziness
• Eye or muscle twitches
10 — ELINCHROM FIVE User manual

• Disorientation
• Any involuntary movement
• Altered vision
• Loss of awareness
• Seizures or convulsion
OUTDOOR USE
CAUTION! PROTECT THE BATTERY PACK AGAINST
HUMIDITY!
This product is designed for dry use and should not come
into contact with water or dust. In humid conditions
cover or otherwise protect the battery unit. Do not
immerse the FIVE unit in water / seawater and do not
allow it to get wet. The unit protection class conforms
to IP20.
TEMPERATURE PRECAUTIONS
To prevent overheating the product should not be
covered whilst in charge mode or in general use! Do
not use, charge or leave the battery near a heat source
(+60°C or higher) such as an open re, a heater or direct
sunlight. If the FIVE unit has been exposed to very cold
conditions, sudden exposure to warm or humid air may
cause condensation and malfunction.
11 — ELINCHROM FIVE User manual

FLASH TUBES & LED-MODELLING LIGHT SAFETY NOTICE
• Flashtubes and the LED-Reector dishes may become
very hot during and after use!
• Never touch a ash tube or exchange it before the unit has
cooled down and is disconnected from the pack.
• Do not re ashes from short distances directed towards
a person.
• Do not look into the bright LED modelling lamp.
• Do not use near ammable / explosive material.
Operating instructions
• The FIVE is a battery monolight unit,
use only the original FIVE Li-Ion
battery. We recommend always
using the Elinchrom 65W USB-C Wall
Charger to charge the FIVE batteries.
• Insert the battery under the unit
and ensure that the battery is well
placed.
• Turn the unit ON.
• DO NOT operate the unit without rst removing the black
protective cap.
• Follow the instructions for tting accessories.
• See features and functions of the FIVE on the following
pages.
12 — ELINCHROM FIVE User manual

Charging / 65W USB-C Wall Charger
Use only the original Elinchrom 65W USB-C Wall
Charger to recharge the built-in Li-Ion battery.
• Recharging time: Approximately 1h35 min. to 100%,
when the battery is plugged into the unit.
• Battery capacity min./max power: approximately
14’600 / 450 ashes per charged battery.
• Recharge the unit only at temperatures from 0° C
to 35° C.
• Recharge the Li-Ion battery before storing the unit.
• If the unit is not frequently used, recharge the unit
after latest 3 months.
FIVE Lithium Ion Battery
USB-C for
re-charging
the battery Battery
release
button
Battery
charge
level
13 — ELINCHROM FIVE User manual

Fitting Accessories
• Always switch the unit off before attaching
accessories.
• Mount the ash unit to a tripod and lock the security
screw.
• Shift the locking knob (on the top of the unit) of the
reector bayonet to the OPEN position.
• Insert an accessory and turn it clockwise until you
hear it click into place.
• Shift the locking knob (on the top of the unit) of the
reector bayonet to the CLOSE position.
• Check if the Reector is correctly tted.
Please use only original Elinchrom accessories and
reectors. The warranty does not cover damage caused
by third party accessories and reectors.
14 — ELINCHROM FIVE User manual

1
3
9
10
4
5678
2
Control panel
1. Umbrella Support 7/8 mm
2. 4 inch LCD Display
3. Favorite button, congure
a specic unit feature as quick
access
4. Modelling Lamp button: short
push (on/off) / long push
(menu access)
5. Menu navigation button
(right/exit) Menu navigation
button (left/back) or power increase by 1 f-stop
6. Scroll button multifunctional
(Test ash, power, navigation)
7. Menu navigation button (left/back) or power decrease
by 1 f-stop
8. Menu access
9. On/off (red illumination indicates the stand-by mode)
10. Photocell
FIVE Inputs (under the unit)
1. Sync plug 3.5 mm jack
2. USB-C
1 2
15 — ELINCHROM FIVE User manual

DISPLAY PANEL – DASHBOARD
The main dashboard displays essential information
about the settings. The colours of the upper bar
correspond to the group number:
Blue for Group 1
Orange for Group 2
Red for Group 3
Green for Group 4
The dedicated Group colour is visible at the illuminated
Elinchrom side logos and on the display.
It is possible to switch between black or white menu
background colour in the Extras settings.
16 — ELINCHROM FIVE User manual

1 2 3 4 5 6 7
12
11
8
9
10
DASHBOARD INFORMATION
Settings that are not enabled are not displayed in
the dashboard. For example, if the modelling lamp is
switched off, the modelling lamp symbol does not appear
on the dashboard.
TTL MODE
The TTL (Through the Lens Metering) mode allows you to
access fully automatic exposure setups according to your
digital camera distance. The TTL values are automatically
saved when passing to the manual mode.
1. Skyport synchronisation.
2. Skyport frequency channel and group number
3. Photocell status
4. Action mode (fast ash duration over the entire power range)
5. Ready beep
6. Fast mode (fast recycling)
7. LED modelling lamp status
8. Increase ash power by 1 f-stop
9. Decrease ash power by 1 f-stop
10. Flash duration value. The ash duration is only visible at normal x-sync
shutter speeds (1/125 or 1/250s depending on the camera)
11. The colour in the upper bar indicates the Group
12. Battery status
17 — ELINCHROM FIVE User manual

To operate the unit in the TTL mode, please use the radio
remote Transmitter Pro and activate the TTL function.
FIRMWARE UPDATES
The functionality is constantly extended and improved,
always use the latest rmware for the Transmitter Pro and
the FIVE ash unit.
LED MODELLING LAMP
Modelling lamp settings are accessible through a dedicated
modelling lamp button.
Controlling the LED/MOD lamp menu access:
• A short press on the modelling lamp button turns on the
LED lamp of the FIVE monolight ash unit.
• A long press on the modelling lamp button opens the
modelling lamp setup menu.
LED MODELLING LAMP MENU FEATURES
Enter the modelling lamp setup menu with a long press
on the modelling lamp button. You can directly adjust the
power of the modelling lamp by turning the scroll button.
To exit the menu press the (right) button.
LED MODELLING LAMP SETTINGS
To access modelling lamp mode prop/free, VFC (visual ash
control) and the mod. lamp timer press the (left) button.
With the scroll button go to the feature (turning) you want
to modify. Now press the scroll button to activate the option
and select (turning) the option and press to conrm.
18 — ELINCHROM FIVE User manual

MENU OPTIONS DESCRIPTION HOW TO
Mode Please choose
between the free
or the proportional
mod. lamp value
setting
Short press on the
left button, change
and conrm with the
scroll button
Free Power value of the
modelling lamp is
independent of the
ash power value.
Use the scroll button
to set the value,
the setting will be
automatically stored.
To modify settings
here, press the left
button to enter into
the menu option.
Propor-
tional
Power value of the
modelling lamp
changes with
the ash power
values.
VFC On / Off Visual Flash
Conrmation.
Timer On / Off The mod. lamp
switches off after
the timeframe set
by the timer value.
Timer
value
Modelling lamp
timer, in sec
19 — ELINCHROM FIVE User manual

RADIO FEATURES & SETUP
The Elinchrom FIVE unit supports the Transmitter Pro,
ensure that both, the unit and the Transmitter Pro are
operating with the latest Firmware.
SKYPORT
Choose in which group and
frequency you would like to work.
Change group settings to have
better control for example between
main light and second lights.
Change frequency channel to avoid
interference.
FLASH MODE SETUP
ACTION MODE
When the Action mode is activated,
the unit offers a fast optimised ash
duration, to freeze motion.
RECYCLING TIME
The ash mode menu enables you to set the recycling
time to fast or to default.
FLASH BEFORE READY
If ash before ready is activated, a ash can be released
before the ash unit is 100% recharged. Deactivated, the
unit will only release a ash when 100% recharged, for
exact exposures at any power level.
20 — ELINCHROM FIVE User manual