Elk Merrell 157-087 User manual

-1- elkhome.com
157-087
Paros Console Table
IMPORTANT
Read all instructions before assembling.
WARNING: To avoid damages, assemble the
product on a soft, clean surface.
CAUTION: Keep small parts out of reach of
children.
Before assembly, remove all parts and part
packages from carton. If anything is missing
or damaged, please contact the retailer from
which the product was purchased or contact
customer service, 800-613-3261.
PACKAGE CONTENTS AB
NOTES:
One-person assembly.
Approx. assembly time: 25 minutes
ANY QUESTIONS CALL: 800-613-3261
M-F 8:00AM-6:00PM ET
C
Parts Quantity
A HEX BOLT - 2.5” 4
B HEX BOLT - 2” 4
C WASHER 8
D HEX WRENCH 1
E TABLE TOP 1
F TABLE LEG 1
G TABLE LEG 2
D
E
F
G

-2- elkhome.com
ASSEMBLY
IMPORTANT: It is recommended to place a
blanket, cardboard or other cushioning material
on the oor to prevent damage to oor and
furniture piece.
1. Hold table leg (F) and one table leg (G) upright.
2. Slide end of table leg (F) through opening in
table leg (G).
3. Align hole in top of table leg (G) with hole in top
of table leg (F).
4. Slip washer (C) over end of one hex bolt (A).
Using hex wrench (D), thread hex bolt (A) with
washer (C) down into hole in top of table leg (G)
and into hole in top of table leg (F). DO NOT
completely tighten hex bolt (A).
5. Carefully place leg assembly on its side on the
oor on top of cushioning material.
6. Slip washer (C) over end of one hex bolt (A).
Using hex wrench (D), thread hex bolt (A) with
washer (C) up through hole in bottom of table
leg (G) and into hole in bottom of table leg (F).
DO NOT completely tighten hex bolt (A).
7. Raise leg assembly so leg assembly is upright on
oor.
8. Repeat steps 2-6 to install second table leg (G)
on other end of table leg (F).
9. Using hex wrench (D), completely tighten hex
bolts (A) in top and bottom of leg assembly (F/G).
157-087
Paros Console Table
A
C
A
C
F
G

157-087
Paros Console Table
ASSEMBLY (CONTINUED)
10. Carefully place table top (E) face down on floor,
on top of cushioning material.
11.
Legs should be placed inside of supporting bar
on underside of top as shown
12. Align holes in leg assembly (F/G) with holes in
underside of table top (E).
13. Slip one washer (C) over end of each hex bolt
(B). Using hex wrench (D), thread each hex bolt
(B) with washer (C) into holes in leg assembly
(F/G) and into holes in underside of table top (A).
14. After all hex bolts (B) are installed, using hex
wrench (D), completely tighten hex bolts (B).
E
F
G
E
B
C
-3- elkhome.com

-4- elkhome.com
157-087
Paros Console Table
MADE IN VIETNAM
IMPORTANT: During the life of the product,
periodically check all screws and xings to
ensure they are secure.
CARE AND CLEANING
• Before using, wipe with a clean, dry cloth.
• Glass may be cleaned with cleaning
products specied safe to use on glass.
• Dust and clean furniture with a clean, non-
colored, lint-free cloth.
• Do not use any cleaners with chemicals,
solvents or harsh abrasives.
• Do not put hot items directly on furniture
surface.
• Do not place furniture in direct sunlight.
• Do not place furniture near heating or
cooling vents.
• Do not write on furniture without a padded
barrier to protect the surface.
• Do not place furniture outside. For indoor
use only.
• Any liquid spilled on the table should be
cleaned up immediately using a damp cloth.
• Avoid rubbing or scratching the surface
with rough or abrasive objects.
PLEASE KEEP INSTRUCTIONS FOR FUTURE
REFERENCE.
ASSEMBLY (CONTINUED)
15. Turn console table upright and place in
permanent location.