Elk S0805-9466 User manual

-1- elkhome.com
S0805-9466
Creative Curve Credenza
Anti-tip strap kit
IMPORTANT
Read all instructions before assembling.
WARNING: To avoid damages, assemble the
product on a soft, clean surface.
CAUTION: Keep small parts out of reach of
children.
Before assembly, remove all parts and part
packages from carton. If anything is missing
or damaged, please contact the retailer from
which the product was purchased or contact
customer service, 800-613-3261.
PACKAGE CONTENTS
A
ASSEMBLY
1. Place one bracket (C) against the back of
the top edge of the credenza.
2. Thread one screw (D) into each hole in
bracket (C) and into back of credenza.
3. Repeat steps 1 and 2 to install second
bracket (C) on other side of back of
credenza.
ANY QUESTIONS CALL: 800-613-3261
M-F 8:00AM-6:00PM ET
Parts Quantity
A Anti-tip strap 2
B Wall anchor 4
C Anti-tip bracket 4
D 0.5" screw 4
E 1.25" screw 4
D
C
C
B
E
CREDENZA TOP
D
WALL
4. Place the credenza in the permanent
location.
5. Place one bracket against wall in line with
one bracket (C) on back of credenza. Mark
the location of the holes in the bracket (C) on
the wall. Drill holes at each marked location
using a drill bit the appropriate size to
accommodate the wall anchors (B).
6. Using a hammer, carefully insert one wall
anchor (B) into each hole in wall.
7. Place bracket (C) on wall. Align holes in
bracket (C) with holes in wall anchors (B).
Thread one wall screw (E) into each hole in
bracket (C) and into holes in wall anchors (B).
8. Repeat steps 5-7 to install remaining
bracket (C) on wall.
NOTE: If wall screws (E) will be installed into
wall studs, anchors are not needed.
E C
B

-2- elkhome.com
C
A
WALL
9. Ensure that all screws (D and E) in brackets (C)
on credenza and in wall are tight.
10.Place credenza against wall aligning
brackets (C) on back of credenza with
brackets (C) on wall. Slip narrow end of
anti-tip strap (A) through slots in bracket (C)
on wall then through slots in bracket (C) on
back of credenza. Slip narrow end of anti-
tip strap (A) through other end of anti-tip
strap (A). Do not completely tighten anti-tip
strap (A) until second anti-tip strap (A) is
installed.
11.Repeat step 10 to install second anti-tip
strap (A) to remaining brackets (C).
12.After both anti-tip straps (A) have been
installed, completely tighten anti-tip straps
(A). DO NOT over tighten.
C
S0805-9466
Creative Curve Credenza
Anti-tip strap kit
WALL
MADE IN INDIA

-3- elkhome.com
S0805-9466
Creative Curve Credenza
INSTRUCTIONS FOR LEVELING CABINET
These steps must be completed to ensure the doors
of the cabinet operate properly.
For cabinet with adjustable leveling glides:
1. Position the cabinet in the desired location.
2. Place the level on the top of the cabinet along
the width (left to right) of the cabinet and adjust
the front adjustable leveling glides until the
bubble in the level is centered.
3. Place the level on the top of the cabinet along
the depth (front to back) of the cabinet and
adjust the rear adjustable leveling glides until
the bubble in the level is centered.
4. Check for plumb in both directions and adjust
the leveling glides if necessary.
TOOLS REQUIRED (NOT INCLUDED):
For cabinet with adjustable leveling glides:
• Bubble level
For cabinet without adjustable leveling glides:
• Bubble level
• Adhesive pads
ADJUSTABLE
LEVELING GLIDE
BUBBLE LEVEL
ADHESIVE PAD
For cabinet without adjustable leveling glides:
1. Position the cabinet in the desired location.
2. Place the level on the top of the cabinet along
the width (left to right) of the cabinet and add
adhesive pads to the bottom of the front legs/
feet until the bubble in the level is centered.
3. Place the level on the top of the cabinet along
the depth (front to back) of the cabinet and add
adhesive pads to the bottom of the rear legs/
feet until the bubble in the level is centered.
4. Check for plumb in both directions and make
adjustments by adding and/or removing
adhesive pads if necessary.
ADHESIVE
PAD