Elko Rf touch-b User manual

USER'S MANUAL

WIRELESS TOUCH

CO N T R O L U N I T

RF Touch user manual

We want to thank you for your purchase of the RF Touch control unit, which is an element of

wireless RF Control system.

RF Touch allows:

you to control many devices trough touch screen

- heating control

- dimming lights

- switching of electrical appliances and equipment

- blinds

- a combination of detectors

- function timers

- Group control of electrical equipment

everything with clear visualization

wireless communication without the need for cabling

RF Touch user manual

Contents:

Before you start ....................... 3

Overview of wireless devices ... 4

Characteristics of RF Touch ..... 6

Technical specifications ........... 7

Installation of RF-Touch W ....... 8

RF Touch Installation-B ............ 9

Description of Control icons .... 10

Basic Steps ............................... 11

Settings

- Default setting ......................... 12

- Menu(creating and naming) ... 13

- Programming ........................... 15

- Assign a new receivers ....... 16

- Assigned receiver ............... 17

- Detectors ............................ 20

- Quick Control ..................... 22

- Display ..................................... 23

- Other ........................................ 23

Control

- Temperature regulation .......... 25

- Switching ................................. 28

- Dimming .................................. 31

- Blinds ....................................... 32

- Detectors ................................. 34

- Quick control............................ 35

What to do if ............................ 36

Installation Form ..................... 38

Before you start

The instruction manual is intended for installation and use of the equipment. Instructions are always included in the product packaging.

Installation and connection can only make personnel with appropriate qualifications, in compliance with all applicable laws, who are

perfectly familiar with this instructions and functions. Trouble free function is also dependent on transportation, storage and handling.

In case of any signs of damage, deformation, malfunction or missing parts, do not install this product and return it to the seller.

Product and its parts must be at the end of its lifetime handled as electronic waste. Before installation, make sure that all wires, connected

parts or terminals are not live. During the installation and maintenance is necessary to follow safety regulations, standards, guidelines

and special provisions for working with electrical equipment.

Overview of wireless RF Control devices

RF Control system

All actuators of the RF Control

System can be controlled by

wireless central unit and all

transmitters of the system

simultaneously.

CENTRAL WIRELESS UNIT

RF Touch-W

for surface mounting

100 - 230V AC or

adapter (external)

12 V DC

CONTROLLER

RF Touch-B

for mounting

in the installation

box

100 - 230V AC

RF Pilot

remote controller,

colours: white,

anthracite

TRANSMITTERS

RF KEY

RFWB-20/G

RFWB-40/G

BLIND ACTUATORS

RFJA-12B/230V

blind actuator

2 x 8A switching

relay protection

230V AC

4-channel remote

controller - key pendant

2-channel wireless

switch in the design

LOGUS90

4-channel Wireless

switch in the design

LOGUS90

RFIM-20B

universal transmitter module

under the switch or button

wall box installation

RFIM-40B

universal transmitter module

under the switch or button

wall box installation

RFSG-1M

Transmitting module

1-module

230 V AC

RFJA-12B/24V DC

blind actuator

contactless switching

12-24V DC

TEMPERATURE ACTUATOR

RFSTI-11B

RFSTI-11/G

RFTI-10B

RFTC-10/G

wireless switching actuator

with temperature sensor

in design to installation box,

230V AC

wireless switching actuator

with temperature sensor

with manual

control buttons directly

on the unit, 230V AC

wireless temperature sensor

1 x CR 2477 3V battery

digital temperature

controller

2 x 1.5V AAA batteries

Overview of wireless RF Control devices

SWITCHING ACTUATORS

RFSA-11B

RFSA-61B

RFSA-62B

RFSA-61M

RFSA-66M

single channel

single function

switching actuator

1 x switching

contact 16 A

230V AC

single channel

multifunction

switching actuator

1 x switching

contact 16A

230V AC

2 channel

multifunction

switching actuator

2 x 8A switching

contact

6 functions

230V AC

single channel

Multifunction

switching actuator

1x changeover

contact 16 A

6 functions

230V AC

six-channel

Multifunction

switching actuator

3 x 8 AND NO

3 x changeover

contact 8A

6 functions 230V AC

DIMMING ACTUATORS

Angle antenna

RFDA-11B

single function

dimming actuator

1 light scene,

function OFF, 230V AC

RFDA-71B

multifunctional dimming actuator

7 functions,

AC 230V / 250V

for plastic

switchboards

supplied as standard

for RFSA-61M,

FSA-66M, RFSG-1M

Angle Antenna

for metal

switchboard

can be ordered for

RFSA-61M,

RFSA-66M, RFSG-1M

ANALOGUE ACTUATOR

RFDAC-71B

Dimmable ballast

Thermo-control

DETECTORS

actuator with analog

output 0 (1) - 10 V

1 x switch contact 16 A

7 functions, 230V AC

for dimming of fluorescent

lamps

supplied on request

with the product RFDAC-71B

of heating valves

supplied on request

with the product RFDAC-71B

JA-80P

JA-81M

JA-82M

Characteristics of RF Touch

Control Unit of the wireless system RF Control - RF Touch provides intelligent control of the RF units.

It can be used for:

Central control of all units from one place

Complete overview (visualization) of the current status of units (appliances / equipment)

Features:

sends command to temperature, switching, dimming and shutter actuators

accepts commands from the transmitters, actuators, temperature sensors and detectors

processing programs for heating and regulation

Design:

RF Touch-B fits in the round installation box with a supply voltage of 100 - 230 V AC

RF Touch-W for surface mounting with power supply from the back side: 100 - 230 V AC or from the side (via jack):

12 V DC

3.5 inch color touch screen - no mechanical buttons

RF Touch frames in the base plastic (white, black) or luxurious design Logus90 (glass, metal)

Color of the interframes - white, ivory, ice, mother of pearl, aluminum, silver

Colors of the boxes (only for RF touch-W) - white, ivory, dark gray, light gray

Backup time in case of power failure is 48 hours

40 actuators and 30 OASIS detectors can be assigned to each RF Touch unit

RF Touch can be combined with units of RF Control marked as Oasis & Touch Compatible

Technical specifications

Technical parameters

Display

Type:

Resolution:

Aspect ratio:

Visible area:

Backlight:

Touch screen:

Display:

Control:

Power supply

Voltage /

specific current:

Power consumption:

Power supply connector:

Control

Range up to:

Minimal range

RF Touch – actuator:

Frequency:

RF Touch-B

RF Touch-W

Technical parameters

Connection

RF Touch-B

push-in

RF Touch-W

screwless terminal

push-in or jack

2.1 mm

color TFT LCD

320 x 240 pixels / 262,144 colors

3:4

52.5 x 70 mm

active (white LED)

resistive 4-wire

3.5”

Touch sensitive

from the back side

100 - 230 V AC

from the side 12 DC *

max. 5 W

A1 - A2

100 m

868 MHz

Max. cross section of wires:

Operating conditions

Operating temperature:

Storage temperature:

Protection:

Overvoltage category:

Pollution degree:

Operating position:

Installation:

Dimensions:

Weight **:

Standards:

max. 2.5 mm

/ 1.5 mm

with socket

0 ... +50°C

- 20 ... +70°C

IP 20

III.

arbitrary

installatin a box

94 x 94 x 12 mm

127 g

EN 60730-1

wall box installation

94 x 94 x 24 mm

175 g

100 - 230 V AC

* adapter is included for RF Touch-W

** weight with plastic frame

RF Touch-W

POWER SUPPLY OVER TERMINALS

POWER SUPPLY OVER ADAPTER

100 - 230V AC

FITTING ON THE SURFACE

adapter included with RFTouch-W

RF Touch-B

POWER SUPPLY OVER TERMINALS

FITTING TO THE INSTALLATION BOX

AC 230V

Description of Control Icons

Basic

RF Touch version Information

and number of assigned units

settings

back to the home screen

step back

Main menu

Temperature regulation

Switching

Dimming

Blinds

Detectors

Quick kontrol

Heating

temperature

Dimming

switch ON

switch OFF

dimming

light inclination

light declination

Switching

switch ON

switch OFF

impuls

button

time function

- delayed switch on

- delayed switch off

0-10V

Setup Menu

scroll up

scroll down

confirm

Keyboard

Blinds

rise blinds

lower blinds

confirm

yes/selected

no/not selected

add

edit/remove

name/adressof the actor(s)

delete

abc

A/a

a/1

dot

letters

small/capital letters

space

switch - the letters / numbers

confirm

erase previous

regulation

Basic Steps for Successful Programming

1st Step – Placing of the RF Touch and RF units

Keep in mind that the radio signal range of RF installation

depends ON building construction, materials and placing of all

units.

Transmission of radio-frequency signals through various materials.

Wooden structures

with plasterboard

plates

2nd Step - Fill Installation Form

- device name that you want to manage (to create a menu)

- the names of units (for the correct classification of the

group, for example: RFSA-61B)- addresses of units (to

identify the actuator, for example: 577515)

Installation form can be found at the end of this manual.

E.g. RFSA-61B

standard glass

Name

80-95 %

80-90 %

brick wall

reinforced concrete

60-90 %

20-60 %

E.g. 577515

Adress

metal plates

0-10 %



3nd Step - Set menus (create names)

Create a list of names of the controlled device in the

Settings / Menu (create name).

4rd Step – Programming

Programming of the RF units with RF Touch is carried out in

the Settings / Programming menu.



SETUP

Initial setup

When the RF Touch is switched on for the first time, you will be automatically redirected to the display calib-

ration screen. Touch screen can be controlled by the light touch (of about0.5-1s) in the desired location. On the

screen (Fig. 1) then appears cross in each corner of the screen, which need to be pressed twice. This will calibrate

the device. The display then shows the RF logo icon



and then touch icon signalizing scanning of the actuators.

fig. 1

Content of the main screen

date

time (touch in the upper right corner of the display will switch between analog

- digital clocks (Figure 2 - Figure 3)

display at the bottom of the screen is customable, eg: heating mode, a often used device ...

Touch the clock area to enter the Main menu. If you want to get to the main menu from

sleep mode, you need to touch the screen anywhere.

fig. 2

fig. 3

Main Menu / Settings

The settings menu can be opened by touch in the

Upper right corner screen on the symbol



and

insertion of password (it´s setting from production – 1111)

(fig. 4-6),which you can change everywhen.

fig. 4

fig. 2

fig. 5

Language

Selection of required

Language - Figure 6.

Save setting by

pressing



fig. 6

Date and time

Settings (Fig.7-8):

Date and Time

automatic

transition between

winter / summer

time (for time

Zone GTM +01:00)

Format settings

hours (12h / 24h

mode)

To save Settings

press



fig. 7

fig. 8

SETUP

Menu (create name)

Menu (create name) is used to add, edit or remove the names of the controlled device. In this menu (Figure 1) you need to first

create your own device names for the sections you want to control.

Creating names is important for successful programming of the RF Touch. For each actuator, which is involved in the installation

you have to create unique name.

The content of this menu is not set at the factory.

Menu (create name) / Add

Press the



Add icon (Fig. 2) to show a selection of sections (Fig. 3):

Temperature regulativ Dimming Blinds Switching Control Speed

Choose the section where you want to add the device name and type your own text (max. 20 characters).

Detectors

Example 1: If you want to control the blinds - Place the name to the section of the blinds (Fig.3-5).

Example 2: If you want to control a group of blinds together, first create all the blinds names in the blinds section and then create new name for group control in Quick

control section.

fig. 1

fig. 2

fig. 3

fig. 4

fig. 5

Note: Actuator RFTI-10B can be connected with two temperature sensors. For each sensor, you can create your own name.

SETUP

Menu (create name) / Edit

Edit button is used to change or modify the name in the crea-

ted menu.

Press the Edit icon



(Fig.1), a menu appears, select the se-

ction in which you want to edit created name (Fig. 2). Mark

selected name by touching it (Fig. 3) and then edit with dis-

played keyboard.

Press



to confirm (Fig. 4). The modified name is stored.

fig. 1

Menu (create name) / Remove

Remove button can delete unit name.

Press the Remove icon



(Fig. 5) following menu appears, se-

lect the section from which you want to remove the name (Fig.

6). Pick the device you want to delete by touching it.(Fig. 7) .

Press



to confirm the selection (Fig. 8). Selected name

will be deleted from menu.

fig. 5

fig. 2

fig. 6

fig. 3

fig. 7

fig. 4

fig. 8

SETUP

Programming

Programming is used to assign or remove the actuators / detectors to menu you created.

The Programming Menu can be entered by entering a password (default - 1111).

Actuators are divided into sections for which they are intended. According to the actuator's type you have to select appropriate

section - see table (eg programming actuator RFSTI-11B - find it in the Temperature regulation section).

RF Control actuators divisions

Temperature

regulation

RFSTI-11B/G

RFTI-10B INx

RFTI-10B OUT

RFTC-10/G

Switching

RFSA-11B

RFSA-6x*

RFDAC-71B

Dimming

RFDA-11B

RFDA-71B

RFDAC-71B

Blinds

RFJA-12B/230V

RFJA-12B/24V DC

Detectors

JA-81M / 82M

JA-80P

fig. 1

fig. 3

internal sensor

external sensor

* RFSA-61B, RFSA-62B,RFSA-61M and RFSA-66M

SETUP

Programming / Assign new

It is used to assign a name to the actuator in the menu. In the required section (heating, dimming ...) select Assign new (Fig. 1). A

list of selected sections actuators will be shown. (Fig. 2). Select the name of the actuator which you want to associate with the

RF Touch. Enter the address of actuator you want to assign( Figure 3) as indicated on the actuator. Confirm with



. From the

menu you created, select the name to which the actuator will be assigned (Fig. 4).

- Only one name can be assigned for each actuator.

- When programming, actuator must be connected with the installation.

Communication test (Fig. 6) is used to detect and display the current status of the RF signal between the RF Touch and progra-

mmed actuator.

- Press Start (Fig. 7) to initiate the test, the current status of the signal is displayed in percentage.

- Press Return to Programming to get back to main menu of programming.

fig. 1

fig. 2

fig. 3

fig. 4

fig. 5

fig. 6

fig. 7

Programming / Temperature regulation / Assign New / RFTI-10B and RFTC-10/G

These two units are temperature sensors, communication test is not executed during programming.

Note: The actuator RFTI-10B is able to be connected with two temperature sensors, each sensor may have its

own name. Address of the actuator is the same for both sensors.

SETUP

Programming / Associated Receivers

It serves to control or remove the actuator from the name of the menu you created.

In the selected section (Figure 1 - Temperature regulation, dimming ...) select Assigned receivers (Fig. 2) a list of names specified

in this section will be shown(Fig. 3). Touching on the name you will assign it to the actuator (Fig. 4).

By pressing



arrows you can check the name and address assigned to the actuator (Fig. 4, 5).

By touching the name or address of the actuator you can remove the actuator (Fig. 7) or carry out communication test (Fig. 8).

fig. 1

fig. 2

fig. 3

fig. 4

fig. 7

fig. 5

fig. 6

fig. 8

SETUP

Programming / Temperature regulation / Assigned receivers / RFTI-10B and RFTC-10/G

Function Assigned receivers in Temperature reg. - RFTI-10B and RFTC-10/G are used to pair or remove temperature units from the actuator.

In the Temperature regulation section, press the screen to select Assigned receivers; the list of names assigned in this section will be

displayed Press the name to display the assigned actuator. Select the name to which the RFTI-10B or RFTI-10/G is assigned (Fig. 1-3).

Use arrows



to check the name and address of the assigned actuator (Fig. 4-5).

Pair with...

Paired with...

Touch the name or address of the actuator to display the menu (Fig. 6):

Remove

Programming / Temperature regulation / Assigned receivers / RFTI-10B and RFTC-10/G / Remove

Serves to cancel the link between the temperature unit and the name from the menu Temperature regulation.

fig. 1

fig. 2

fig. 3

fig. 4

fig. 6

fig. 5

SETUP

Programming / Temperature regulation / Assigned receivers / RFTI-10B and RFTC-10/G / Pair with...

Serves to combine the RFTI-10B or RFTC-10/G temperature unit with the RFSA-61M or RFSA-61B or RFDAC-71B multifunction actua-

tor, where the temperature unit measures the current temperature and the multifunction actuator switches on the Temperature re-

gulation based on the measured temperature. The multifunction actuator switches based on the set temperatures in the RF Touch.

Note: the attached actuator RFTI-10B can be used in two ways:

For temperature measurement (without pairing with a switching actuator)

When paired with the multifunction switching actuator it can switch heating equipment on the basis of the measured temperature.

Programming / Temperature regulation / Assigned receivers / RFTI-10B and RFTC-10/G / Paired with...

Shows multifunction switching actuator, which is paired with a temperature actuator. By touching the name of the actuator you

can remove a paired actuator.

Note: Battery indication on the display (Fig. 1) informs of low battery in one of the temperature units. Press the battery to display the unit name. Use arrows

