DMP Electronics XR100 Operating instructions

PROGRAMMING GUIDE
XR100 SERIES
COMMAND PROCESSOR™ PANEL

XR100 Series Programming Guide Digital Monitoring Products
i
TABLE OF CONTENTS
MODEL XR100 SERIES ACCESS CONTROL
COMMAND PROCESSOR™ PANEL
PROGRAMMING GUIDE
Contains programming instructions for use with the Model
XR100 and XR100N Access Control Command Processor™ Panel.
When using the XR100 Series panel for any UL, NFPA, CSFM, or other listing organization’s approved methods, refer to this
manual and the XR100 Series Installation Guide (LT-0899). These documents outline the installation and programming
requirements of all applications for which the XR100 Series is approved.
FCC NOTICE
This equipment generates and uses radio frequency energy and, if not installed and used properly in strict accordance
with the manufacturer’s instructions, may cause interference with radio and television reception. It has been type tested
and found to comply with the limits for a Class A computing device in accordance with the specication in Subpart J
of Part 15 of FCC Rules, which are designed to provide reasonable protection against such interference in a residential
installation. If this equipment does cause interference to radio or television reception, which can be determined by
turning the equipment off and on, the installer is encouraged to try to correct the interference by one or more of the
following measures:
Reorient the receiving antenna
Relocate the computer with respect to the receiver
Move the computer away from the receiver
Plug the computer into a different outlet so that computer and receiver are on different branch circuits
If necessary, the installer should consult the dealer or an experienced radio/television technician for additional suggestions.
The installer may nd the following booklet, prepared by the Federal Communications Commission, helpful:
“How to identify and Resolve Radio-TV Interference Problems.”
This booklet is available from the U.S. Government Printing Ofce, Washington D.C. 20402
Stock No. 004-000-00345-4
© 2006-2007 Digital Monitoring Products, Inc.
Information furnished by DMP is believed to be accurate and reliable.
This information is subject to change without notice.

XR100 Series Programming Guide Digital Monitoring Products
i
TABLE OF CONTENTS
Revisions to This Document...........................................viii
Introduction......................................................................1
1.1 Before you Begin ................................................................. 1
Internal Programmer............................................................ 1
Programming Information Sheet ........................................... 1
1.2 Getting Started.................................................................... 1
Accessing the Programmer ................................................... 1
1.3 Programmer Operation......................................................... 2
1.4 Programmer Lockout Codes.................................................. 2
1.5 Reset Timeout..................................................................... 2
1.6 Power Up ............................................................................ 2
1.7 Keypads ............................................................................. 3
1.8 Special Keys ........................................................................ 3
COMMAND (CMD) Key.......................................................... 3
Back Arrow (<—) Key .......................................................... 3
Select Keys/Areas ................................................................ 3
1.9 Entering Alpha Characters .................................................... 4
1.10 Entering Non-Alpha Characters ............................................. 4
1.11 Keypad Displays Current Programming .................................. 5
1.12 Asterisks in Programming ..................................................... 5
Initialization .....................................................................6
2.1 Initialization ........................................................................ 6
2.2 Clear All Memory ................................................................. 6
2.3 Clear All Codes .................................................................... 6
2.4 Clear All Schedules .............................................................. 6
2.5 Clear Display Events Memory................................................ 6
2.6 Clear Zone Information ........................................................ 6
2.7 Clear Area Information......................................................... 6
2.8 Clear Output Information ..................................................... 6
2.9 Clear Communication and Remote Options ............................ 7
2.10 Set to Factory Defaults......................................................... 7
Communication .................................................................8
3.1 Communication ................................................................... 8
3.2 Communication Type............................................................ 8
3.2.1 Retry Time .......................................................................... 8
3.2.2 Network Backup .................................................................. 8
3.2.3 Supervise Backup ................................................................ 8
3.2.4 Remote IP Address .............................................................. 9
3.2.5 Alarm Port........................................................................... 9
3.2.6 Modem Setup...................................................................... 9
3.2.7 UL AA ................................................................................. 9
Disarm Checkin ................................................................... 9
3.2.8 Network Test .....................................................................10
3.2.9 Substitution Code ...............................................................10
3.2.10 Check In ............................................................................10
3.2.11 Fail Time............................................................................10
3.2.12 Network Trouble .................................................................10
3.3 Second Line .......................................................................11
3.4 Test Frequency ...................................................................11
3.5 NET Fail Test ......................................................................12
3.6 Account Number.................................................................12
3.7 Transmit Delay ...................................................................12
3.8 DTMF.................................................................................12
3.9 Defer Test .........................................................................12
3.10 Test Frequency ...................................................................12

Digital Monitoring Products XR100 Series Programming Guide
ii
TABLE OF CONTENTS
XR100 Series Programming Guide Digital Monitoring Products
iii
TABLE OF CONTENTS
3.11 Test Time...........................................................................12
3.12 Events Manager..................................................................13
3.13 Receiver One Programming .................................................13
3.14 Alarm Reports ....................................................................13
3.15 Supervisory/Trouble Reports................................................13
3.16 Opening/Closing and User Reports.......................................13
3.17 Test Report ........................................................................13
3.18 Door Access Report.............................................................13
3.19 Backup Reporting ...............................................................13
3.20 First Telephone Number ......................................................14
3.21 Second Telephone Number..................................................14
3.22 Receiver Two Programming .................................................14
3.23 Alarm Reports ....................................................................14
3.24 Supervisory/Trouble Reports................................................14
3.25 Opening/Closing and User Reports.......................................15
3.26 Test Report ........................................................................15
3.27 Door Access Report.............................................................15
3.28 Backup Reporting ...............................................................15
3.29 First Telephone Number ......................................................15
3.30 Second Telephone Number..................................................15
Network Options (XR100N only) ......................................16
4.1 DHCP Mode Enabled ...........................................................16
4.2 Local IP Address.................................................................16
4.3 Gateway Address................................................................16
4.4 Subnet Mask ......................................................................16
4.5 Programming Port...............................................................16
4.6 TCP Comm Enabled ............................................................16
Device Setup ...................................................................17
5.1 Device Setup ......................................................................17
5.2 Device Number...................................................................17
5.3 Door Name .......................................................................17
5.4 Access Areas ......................................................................17
5.5 Egress Areas ......................................................................17
5.6 Display Areas .....................................................................18
5.7 Strike Time ........................................................................19
5.8 Strike Delay........................................................................19
5.9 Fire Exit Release .................................................................19
5.10 Output Group .....................................................................19
5.11 Schedule Override ..............................................................19
5.12 Auto Force Arm Device? ......................................................19
Remote Options ..............................................................20
6.1 Remote Options..................................................................20
6.2 Remote Key .......................................................................20
6.3 Manufacturer Authorization .................................................20
6.4 Armed Rings ......................................................................20
6.5 Disarmed Rings ..................................................................20
6.6 Alarm Receiver Authorization ...............................................20
6.7 Service Receiver Authorization .............................................21
6.8 PC Modem ........................................................................21
6.9 Remote Telephone Number .................................................21
6.10 Remote Disarm ..................................................................21
System Reports...............................................................22
7.1 System Reports ..................................................................22
7.2 Abort Report ......................................................................22
7.3 Restoral Reports .................................................................22
7.4 Bypass Reports...................................................................22

Digital Monitoring Products XR100 Series Programming Guide
ii
TABLE OF CONTENTS
XR100 Series Programming Guide Digital Monitoring Products
iii
TABLE OF CONTENTS
7.5 Schedule Change Reports....................................................22
7.6 Code Change Reports .........................................................22
7.7 Access Keypads ..................................................................22
7.8 Ambush ............................................................................22
System Options ...............................................................23
8.1 System Options ..................................................................23
8.2 System ..............................................................................23
8.3 Closing Wait .......................................................................23
8.4 Entry Delay 1 .....................................................................23
8.5 Cross Zone Time.................................................................23
8.6 Zone Retard Delay ..............................................................24
8.7 Power Fail Delay .................................................................24
8.8 Swinger Bypass Trips ..........................................................24
8.9 Reset Swinger Bypass .........................................................24
8.10 Video/Alarm Verication ......................................................24
8.11 Time Zone Changes ............................................................25
8.12 Latch Supervisory Zones .....................................................25
8.13 Programming Menu Language ............................................25
8.14 User Menu and Status List Language ...................................26
8.15 Bypass Limit.......................................................................26
8.16 House Code .......................................................................26
8.17 Detect Wireless Jamming ....................................................26
8.18 Enable Keypad Panic Keys ...................................................27
8.19 SIA CP-01 ..........................................................................27
Output Options ...............................................................28
9.1 Output Options...................................................................28
9.2 Bell Cutoff Time..................................................................28
9.3 Automatic Bell Test ............................................................28
9.4 Bell Action..........................................................................28
9.4.1 Fire Bell Action ...................................................................28
9.4.2 Burglary Bell Action.............................................................28
9.4.3 Supervisory Bell Action........................................................28
9.4.4 Panic Bell Action .................................................................28
9.4.5 Emergency Bell Action.........................................................28
9.4.6 Auxiliary 1 Bell Action..........................................................28
9.4.7 Auxiliary 2 Bell Action..........................................................28
9.5 Output Action.....................................................................28
9.5.1 Cutoff Output ....................................................................29
9.5.2 Output Cutoff Time.............................................................29
9.5.3 Communication Fail Output .................................................29
9.5.4 Fire Alarm Output ...............................................................29
9.5.5 Fire Trouble Output.............................................................29
9.5.6 Panic Alarm Output.............................................................29
9.5.7 Ambush Output ..................................................................29
9.5.8 Entry Output ......................................................................29
9.5.9 Exit Output.........................................................................29
9.5.10 Ready Output.....................................................................29
9.5.11 Telephone Trouble Output ...................................................30
9.5.12 Late To Close Output ..........................................................30
9.5.13 Device Fail Output ..............................................................30
9.5.14 Sensor Reset Output...........................................................30
9.5.15 Closing Wait Output ............................................................30
9.6 Output Names ....................................................................30
9.6.1 Output Number .................................................................30
9.6.2 Output Name .....................................................................30

Digital Monitoring Products XR100 Series Programming Guide
iv
TABLE OF CONTENTS
XR100 Series Programming Guide Digital Monitoring Products
v
TABLE OF CONTENTS
Output Groups ................................................................31
10.1 Output Groups....................................................................31
10.2 Group Number....................................................................31
10.3 Group Name ......................................................................31
10.4 Output Number ..................................................................31
Menu Display...................................................................32
11.1 Menu Display .....................................................................32
11.2 Armed Status .....................................................................32
11.3 Time .................................................................................32
11.4 Arm/Disarm........................................................................32
Status List .......................................................................33
12.1 Status List .........................................................................33
12.2 Display Keypads .................................................................33
12.3 System Monitor Troubles .....................................................33
12.4 Fire Zones ..........................................................................33
12.5 Burglary Zones ...................................................................34
12.6 Supervisory Zones ..............................................................34
12.7 Panic Zones........................................................................34
12.8 Emergency Zones ...............................................................34
12.9 Auxiliary 1 Zones ................................................................34
12.10 Auxiliary 2 Zones ................................................................34
PC Log Reports................................................................35
13.1 PC Log Reports...................................................................35
13.2 PC Log Address ..................................................................35
13.3 Arm and Disarm Reports .....................................................35
13.4 Zone Reports......................................................................35
13.5 User Command Reports ......................................................35
13.6 Door Access Reports ...........................................................35
13.7 Supervisory Reports............................................................35
Area Information ............................................................36
14.1 Area Information ................................................................36
14.2 Exit Delay ..........................................................................36
14.3 Burglary Bell Output ...........................................................36
14.4 Opening/Closing Reports.....................................................36
14.5 Closing Check.....................................................................37
14.6 Closing Code ......................................................................37
14.7 Any Bypass ........................................................................37
14.8 Area Schedules...................................................................37
14.9.1 Area Number......................................................................37
14.9.2 All/Perimeter Programming..................................................37
14.9.3 Home/Sleep/Away Programming..........................................37
14.10 Area Name.........................................................................37
14.11 Account Number.................................................................38
14.12 Automatic Arming ...............................................................38
14.13 Bad Zones..........................................................................38
14.14 Automatic Disarming...........................................................38
14.15 Armed Output Number........................................................38
14.16 Late Output Number ...........................................................38
14.17 Late Arm Delay...................................................................38
14.18 Common Area ....................................................................39
14.19 Arm First Area ....................................................................39

Digital Monitoring Products XR100 Series Programming Guide
iv
TABLE OF CONTENTS
XR100 Series Programming Guide Digital Monitoring Products
v
TABLE OF CONTENTS
Zone Information............................................................40
15.1 Zone Information................................................................40
15.2 Zone Number .....................................................................40
15.3 Zone Name ........................................................................40
15.4 Zone Type ..........................................................................41
15.5 Area Assignment ................................................................41
15.6 Fire Bell Output ..................................................................41
15.7 Arming Zone Area Assignment .............................................42
15.8 Style..................................................................................42
15.9 Next Zone ..........................................................................43
15.10 Wireless.............................................................................43
15.10.1 Serial Number Entry............................................................43
15.10.2 Contact..............................................................................43
15.10.3 Supervision Time ................................................................44
15.10.4 LED Operation....................................................................44
15.10.5 Next Zone ..........................................................................44
15.11.1 Key Fob User Number .......................................................44
15.11.2 Key Fob Serial Number........................................................45
15.11.3 Key Fob Supervision Time ...................................................45
15.11.4 Number of Key Fob Buttons ...............................................45
15.11.5 Key Fob Button Selection (Four Buttons) ..............................45
15.11.6 Key Fob Button Selection (Two Buttons) ..............................45
15.11.7 Button Action .....................................................................45
15.11.8 Button Press Time ..............................................................46
15.11.9 Arm/Disarm Area Selection..................................................46
15.11.10 Output Number ..................................................................46
15.11.11 Output Action.....................................................................47
15.11.12 Next Zone ..........................................................................47
15.12 Alarm Action ......................................................................47
15.13 Disarmed Open .................................................................47
15.14 Report to Transmit..............................................................48
15.15 Output Number ..................................................................48
15.16 Output Action.....................................................................48
15.17 Swinger Bypass ..................................................................49
15.18 Prewarn Keypad Addresses..................................................49
15.19 Entry Delay ........................................................................49
15.20 Zone Retard Delay ..............................................................49
15.21 Presignal Addresses ............................................................49
15.22 Fast Response ....................................................................49
15.23 Cross Zone .........................................................................50
15.24 Priority ..............................................................................50
Stop.................................................................................51
16.1 Stop ..................................................................................51
Set Lockout Code ............................................................51
17.1 Set Lockout Code................................................................51
Feature Upgrade .............................................................52
18.1 Feature Upgrade.................................................................52
18.1.1 All No Yes Option................................................................52
18.1.2 Service User Authentication .................................................52
Purchasing Feature Upgrades ..............................................52

Digital Monitoring Products XR100 Series Programming Guide
vi
TABLE OF CONTENTS
XR100 Series Programming Guide Digital Monitoring Products
vii
TABLE OF CONTENTS
Appendix .........................................................................53
19.1 False Alarm Reduction.........................................................53
System Recently Armed report.............................................53
19.2 Diagnostics function............................................................53
Test LX-Bus ........................................................................53
Zone Finder........................................................................53
Zone State .........................................................................53
LX-Bus Status .....................................................................53
MAC Address......................................................................54
Serial Number ....................................................................54
Current Flash......................................................................54
Send Test Message .............................................................54
Exiting the Diagnostics program...........................................54
19.3 Using the 984 Command Function........................................54
NBR...................................................................................54
RMT .................................................................................55
PICKUP ..............................................................................55
Keypad Displays .................................................................55
19.4 Using the Walk Test ............................................................55
Walk Test ..........................................................................55
Zone Types ........................................................................56
Bell Action..........................................................................56
Trip Counter .......................................................................56
Test End Warning ...............................................................56
Failed Zones Display ...........................................................56
19.5 Keypad Speaker Operation ..................................................57
19.6 Cross Zoning ......................................................................57
19.7 Events Manager..................................................................57
19.8 User Proles.......................................................................58
19.9 User Proles Record............................................................59
19.10 Zone Type Descriptions .......................................................60
19.11 Zone Type Specications ....................................................61
19.11.1 Keypad Bus Zone Type Defaults ...........................................61
19.11.2 LX-Bus Zone Type Defaults ..................................................62
19.12 Common Keypad Messages .................................................63
Listings and Approvals....................................................64

Digital Monitoring Products XR100 Series Programming Guide
vi
TABLE OF CONTENTS
XR100 Series Programming Guide Digital Monitoring Products
vii
TABLE OF CONTENTS
This page intentionally left blank.

Digital Monitoring Products XR100 Series Programming Guide
viii
REVISIONS
XR100 Series Programming Guide Digital Monitoring Products
1
INTRODUCTION
Revisions to This Document
This section explains the changes made to this document during this revision. It lists the date and identies
the change(s) made, the related section number and section heading, and a summary of the change.
Date Section Number and Heading Quick Explanation of Changes
1/07 3.3 Second Line Removed Telephone from title.
8.6 Zone Retard Delay Added Panic as a zone type option.
11/06 1.6 Power Up Revised for SIA CP-01 option operation.
3.2.2 Network Backup Option revised for new programming operation.
3.2.3 Supervise Backup Option added for new programming operation.
Note: Subsequent section numbers changed.
3.2.6 Modem Setup Added Supervise Backup operation information.
3.2.9 Substitution Code Added note regarding Net Backup and Supervise Backup operation.
3.2.10 Check In Added note regarding Net Backup and Supervise Backup operation.
5.4 Access Areas Added note regarding All/Perimeter, Home/Sleep/Away operation.
5.5 Egress Areas Added note regarding All/Perimeter, Home/Sleep/Away operation.
5.6 Display Areas Added note regarding All/Perimeter, Home/Sleep/Away operation.
8.2 System Option added for new programming operation.
Note: Subsequent section numbers changed.
8.4 Entry Delay 1 Added note regarding SIA CP-01 option operation.
8.19 SIA CP-01 Option added to enable specic SIA CP-01 operations.
14.2 Exit Delay Added note regarding SIA CP-01 option operation.
14.8 Area Schedules Added note regarding All/Perimeter, Home/Sleep/Away operation.
14.9.1 Area Number Added note regarding All/Perimeter, Home/Sleep/Away operation.
14.9.2 All/Perimeter Programming Option added for new programming operation.
14.9.3 Home/Sleep/Away Programming Option added for new programming operation.
14.12 Automatic Arming Added note regarding SIA CP-01 UL installations.
14.14 Automatic Disarming Added note regarding SIA CP-01 UL installations.
15.5 Area Assignment Added All/Perimeter, Home/Sleep/Away operation.
15.7 Arming Zone Area Assignment Added All/Perimeter, Home/Sleep/Away operation.
15.11 1100 Series Key Fobs Added information regarding Key Fob user operation.
15.11.9 Arm/Disarm Areas Added All/Perimeter, Home/Sleep/Away operation.
16.1 Stop Revised for SIA CP-01 option operation.
19.9 User Proles Added note regarding All/Perimeter, Home/Sleep/Away operation.
19.12.1 Keypad Bus Zone Type Defaults Added Keypad Bus Zone Information Table with All/Perimeter, Home/
Sleep/Away operation and related Defaults list.
19.12.2 LX-Bus Zone Type Defaults Added All/Perimeter, Home/Sleep/Away operation to LX-Bus Zone
Information Table and related Defaults list.
10/06 8.15 House Code Option added for new wireless programming operation.
8.16 Detect Wireless Jamming Option added for new wireless programming operation.
8.17 Enable Keypad Panic Keys Option added to allow override of Keypad two-button panic function.
15.2 Zone Number Added zone numbers for new wireless programming operation.
15.9 Next Zone Revised to cover new wireless programming operation.
15.10 DMP Wireless Section added for new wireless programming options.
Added note regarding UL installations.
15.11 1100 Series Wireless Key Fob Section added for new wireless programming options.
Added note regarding UL installations.
Note: Subsequent section numbers changed.
19.11 Zone Type Specications Added revised table and text to reect new DMP Wireless options.
19.12 Common Keypad Messages Added new wireless keypad messages.

Digital Monitoring Products XR100 Series Programming Guide
viii
REVISIONS
XR100 Series Programming Guide Digital Monitoring Products
1
INTRODUCTION
Introduction
1.1 Before you Begin
This guide provides programming information for the DMP XR100 and XR100N Command Processor™ Panel.
After this Introduction, the remaining sections describe the functions of each programming menu item
along with the available options. Before starting to program, we recommend that you read through the
contents of this guide. The information contained here allows you to quickly learn the programming
options and operational capabilities of the XR100 and XR100N panels.
In addition to this guide, you should also read and be familiar with the following XR100 Series documents:
• XR100 Series Installation Guide (LT-0899)
• XR100 Series Programming Sheet (LT-0897)
• XR500/XR100 Security Command® User’s Guide (LT-0683)
Internal Programmer
The panel contains all of its programming information in an on-board processor and does not require an
external programmer. You can perform all programming tasks through a 32-character DMP alphanumeric
keypad set to address one.
Programming Information Sheet
Included with each panel are the Programming Information Sheets. These list the various programming
prompts and available options for programming the panel. Before starting to program, we recommend you
completely ll out each sheet with the programming options you intend to enter into the panel.
Having completed programming sheets available before entering data helps prevent errors and can shorten
the time you spend programming. Completed sheets also provide you with an accurate panel program
record you can keep on le for future system service or expansion. The remainder of this Introduction
provides instructions for starting and ending a programming session using the alphanumeric keypad.
1.2 Getting Started
Ground Yourself Before Handling the Panel! Touch any grounded metal, such as the enclosure, before
touching the panel to discharge static.
Remove All Power From the Panel! Remove all AC and Battery power from the panel before installing or
connecting any modules, cards, or wires to the panel.
Before starting to program the XR100 Series panel, make sure the panel is properly grounded and AC
and battery power is applied to the appropriate panel terminals. All wiring connections and grounding
instructions are detailed in the XR100 Series Installation Guide (LT-0899).
Accessing the Programmer
1. Install the reset jumper across the two J16
reset pins for two seconds.
2. Remove the reset jumper and place it over
just one pin for future use.
3. Enter the code 6653 (PROG) into a
32-character alphanumeric keypad set
to address one, supervised mode. Press
COMMAND.
Note: If the keypad displays ENTER CODE:,
a lock out code is required.
4. The keypad displays PROGRAMMER.
You are now ready to start programming the panel.




                          
                       
 
 















 
















Figure 1: XR100 Series Panel Showing Reset

Digital Monitoring Products XR100 Series Programming Guide
2
INTRODUCTION
XR100 Series Programming Guide Digital Monitoring Products
3
INTRODUCTION
1.3 Programmer Operation
There are 17 programming sections to choose from:
Programming Item Section in this manual Programming Item Section in this manual
Initialization 2 Menu Display 11
Communication 3 Status List 12
Network Options 4 PC Log Reports 13
Device Setup 5 Area Information 14
Remote Options 6 Zone Information 15
System Reports 7 Stop 16
System Options 8 Set Lockout Code 17
Output Options 9 Feature Upgrade 18
Output Groups 10
To choose a section for programming, press any top row Select key when the keypad displays the name of
that section. Sections 2 through 18 contain detailed instructions for each programming step.
1.4 Programmer Lockout Codes
The panel allows you to enter the programming function without entering a lockout code using steps
1 to 4 listed in Getting Started. We recommend, however, that you install a Lockout Code to restrict
programming to only those persons your company authorizes. You can do this by using the SET LOCKOUT
CODE feature in the Programmer. The Lockout Code restricts any unauthorized panel programming.
After resetting the panel and entering the code 6653, the keypad displays PROGRAMMER. Press COMMAND
to advance through the programming sections until SET LOCKOUT CODE displays (after STOP). Press any
top row Select key. The keypad displays ENTER CODE: – . Enter a 3 to 5 digit Programmer Lockout Code
and press COMMAND. The keypad displays ENTER AGAIN followed by ENTER CODE: –. Enter the same 3 to
5 digit code a second time and press COMMAND. The keypad displays CODE CHANGED.
Note: The panel will not accept a 5-digit Lockout Code higher than 65535.
Before accessing programmer functions enter the new code number.
Write the Lockout Code number down and keep it in a secure place with access limited to authorized
persons only. Lost Lockout Codes require the panel to be sent back to DMP for repair. You may cancel a
Lockout Code by entering 00000 at the Set Lockout Code command.
1.5 Reset Timeout
The panel has a feature that requires you to enter the Programmer within 30 minutes of resetting the
panel. After 30 minutes, if you attempt to program by entering the 6653 (PROG) code, the keypad
displays: RESET PANEL. You must reset the panel and enter the program code then begin programming
within the next 30 minutes.
If you are already in the Programmer and do not press any keys on the programming keypad for 30 minutes,
the panel terminates programming. All data entered up to that time is Not saved unless you run the Stop
routine.
Note: Use the Stop routine to exit panel Programming. Ensure the keypad displays “SAVING PROGRAM”
to save all programming changes entered.
1.6 Power Up
When the SIA CP-01 option in System Options is set to Yes, for 60 seconds after power up or after applying
the J16 reset on the XR100 Series panel, any zone transitions are not recognized. Normal zone processing
resumes at the end of the 60 seconds.

Digital Monitoring Products XR100 Series Programming Guide
2
INTRODUCTION
XR100 Series Programming Guide Digital Monitoring Products
3
INTRODUCTION
1.7 Keypads
DMP offers multiple keypads in a variety of styles. All DMP keypads provide the same programming
capabilities. Each keypad and its operation are shown and described in the following sections.
        
          
 

 
   
  

      








�
32-Character Display
Armed LED
Power LED
Data Entry Digit keys
COMMAND Key
Back Arrow Key
Select Keys
1 2 3 4
9 0 CMD
5 6 7 8
ABC PRINTING
F R I 2 : 51 AM
Figure 3: Security Command Keypad Figure 4: Thinline/Aqualite Keypad
AC Power/Armed LED
Three Panic Icons
32-Character
Display with
Four Touch
Select Areas
Data Entry
Digit Keys
COMMAND KeyBack Arrow Key
Logo
Icon
I
FRI
:
2
51
A
AM
Figure 5: Clear Touch Keypad
1.8 Special Keys
The following special keys/areas are common to all DMP keypads.
COMMAND (CMD) Key
Pressing the COMMAND key allows you to go forward through the programming menu and through each
step of a programming section. As you go through the programming, the keypad display shows any current
programming already stored in the panel memory. If no change is required for a prompt, press the
COMMAND key to advance to the next step.
The COMMAND key is also used to enter information into the panel’s memory such as phone numbers or
zone names. Press the COMMAND key after entering information.
Back Arrow (<—) Key
Use the Back Arrow key to back up one step while programming. The Back Arrow key is also used when
an error is made while entering information. Press the Back Arrow key once to erase the last character
entered.
Select Keys/Areas
The top row of keys are called the Select keys on Security Command, Thinline, and Aqualite keypads or
Select Areas on Clear Touch keypads. Each time you need to press a Select key, the keypad displays the
function or options above one of the keys or in the Select Area. Displaying choices above individual Select
keys or in Select Areas allows them to be used for many different applications. For example, you can enter
AM or PM when programming the automatic test time or answer YES or NO for a system option.
During programming, the Select keys/areas also allow you to change information currently in panel memory
by pressing the appropriate Select key/area under or on the display. You then enter the new information
using the keypad data entry digit keys.

Digital Monitoring Products XR100 Series Programming Guide
4
INTRODUCTION
XR100 Series Programming Guide Digital Monitoring Products
5
INTRODUCTION
When there are more than four response options available, press the COMMAND key to display the next one
to four options. Pressing the Back Arrow key allows you to review the previous four choices.
The Select keys/areas are also used for choosing a section from the programming menu. Press any Select
key or touch the Select Area when the programming section name you want displays.
Note: On Security Command, Thinline and Aqualite keypads, when instructed to press the rst Select
key, press the far left Select key; the second Select key is the second from the left; third Select key is
second from the right; and the fourth Select key is the far right key. See Figures 6 and 7.
On Clear Touch Keypads, when instructed to press the rst Select key, touch Select Area 1; the second
Select key touch Select Area 2; third Select key touch Select Area 3; and the fourth Select key touch Select
Area 4. See Figure 8.
1.9 Entering Alpha Characters
Some options during programming require you to enter alpha characters. To enter an alpha character,
press or touch the key that has that letter written below it. The keypad displays the number digit of the
key. Next, press the Select key/area that corresponds to the location of the letter under the key. Pressing
a different Select key/area changes the letter. When another digit key is pressed, the last letter displayed
is retained and the process starts over.
   

First Letter
Second Letter
Third Letter
Special Character
(CBA
Figure 6: Security Command Select Keys Figure 7: Thinline/Aqualite Select Keys
32-Character Display
Select Area 1
Select Area 2 Select Area 3
Select Area 4
Figure 8: Clear Touch Select Areas
1.10 Entering Non-Alpha Characters
To enter a space in an alpha entry, press the 9 digit key followed by the third Select key/area. The three
characters on the 9 digit key are Y, Z, and space. You can also enter the following characters: – (dash),
. (period), * (asterisk), and # (pound sign) using the 0 (zero) key and the four Select keys/areas from left
to right. For example, to enter a – (dash), press the 0 (zero) key and then the left Select key/area. A dash
now appears in the keypad display. Figures 9 and 10 show the character location for
Security Command, Thinline, and Aqualite keypads. Figure 11 shows the character
locations for Clear Touch keypads.
 
   
   



 
1 2 3 4
9 0 CMD
5 6 7 8
A
(
C
B
D
)
F
E
G
!
I
H
J
?
L
K
V
,
X
W
S
$
U
T
P
&
R
Q
M
/
O
N
Y
'
(space)
Z
-
#
*
.
Figure 9: Security Command Figure 10: Thinline/Aqualite
Special Characters Special Characters
ABC( DEF) GHI!
JKL? MNO/ PQR&
STU$ VWX, YZ(SPACE)'
–.*#
Figure 11: Clear Touch
Special Characters

Digital Monitoring Products XR100 Series Programming Guide
4
INTRODUCTION
XR100 Series Programming Guide Digital Monitoring Products
5
INTRODUCTION
1.11 Keypad Displays Current Programming
Each programming prompt displayed at the keypad shows the currently selected option in the panel
memory. These options are either shown as a number, a blank, or a NO or YES. To change a number or
blank to a new number, press any top row Select key or touch any Select Area. The current option is
replaced with a dash. Press the number(s) on the keypad you want to enter as the new number for that
prompt. It is not necessary to enter numbers with leading zeros. The panel automatically right justies
the number when you press the COMMAND key.
To change a programming prompt that requires a NO or YES response, press the Select key or touch the
Select Area for the response not selected. See Figure 12.
For example, if the current prompt is selected as YES and you want to change it to NO, on Security
Command, Thinline, or Aqualite keypads press the third top row Select key. On Clear Touch keypads touch
Select Area 3. The display changes to NO. Press the COMMAND key to display the next prompt.

 


 


 
 









Figure 12: Changing the Current Programming Option
1.12 Asterisks in Programming
Asterisks display next to a programming option that is already selected. As shown in the example, options
that are selected to display the current programming selection have an asterisk next to the number. Those
that are not selected simply display the number. In the Devices example, keypads 3, 6, and 8 are not
selected. In the Areas example, areas 3, 6, and 8 are not selected. In both examples the numbers with
asterisks are selected.
Devices Areas
*1 *2 3 *4 *1 *2 3 *4
*5 6 *7 8 *5 6 *7 8
To select or deselect a number, simply enter the number using the digit keys on the keypad. This same
scheme is used when viewing the panel armed status and other programming and operational functions.
Remember to press the COMMAND key to display the rest of the device or area numbers.

Digital Monitoring Products XR100 Series Programming Guide
6
INITIALIZATION
XR100 Series Programming Guide Digital Monitoring Products
7
INITIALIZATION
Initialization
NOTE: WHEN ANY PANEL PROGRAMMING IS CHANGED, THE STOP ROUTINE MUST BE RUN AND ‘SAVING
PROGRAM’ MUST DISPLAY ON THE KEYPAD IN ORDER TO SAVE THE PROGRAMMING CHANGES. SEE SECTION 17.1.
2.1
INITIALIZATION
Initialization
This function allows you to clear selected parts of the panel program back to the
factory defaults in preparation for system programming. Run the initialization
function on all new installations.
  
  









  


2.2
INIT ALL? NO YES
SURE? YES NO
Clear All Memory
NO - Leaves existing programming intact then displays Clear All Codes.
YES - Clears all memory then displays Reset Panel. Reset the panel by shorting J16
and re-enter programming mode to continue.
2.3
CODES? NO YES
SURE? YES NO
Clear All Codes
NO - Leaves existing codes intact.
YES - Clears the user code and user prole memory and assigns user code number 99
to the highest user position.
Note: The user name for the default user code is created using the current
programmed primary user language.
2.4
SCHEDS? NO YES
SURE? YES NO
Clear All Schedules
NO - Leaves existing schedules intact.
YES - Clears all shift, and output schedules.
2.5
EVENTS? NO YES
SURE? YES NO
Clear Display Events Memory
NO - Leaves existing event memory intact.
YES - Clears the events memory.
2.6
ZONES? NO YES
SURE? YES NO
Clear Zone Information
NO - Leaves existing zone information intact.
YES - Clears the zone information for all zones. All zones are marked * UNUSED *
and must be renamed before being able to display on any system keypad.
2.7
AREAS? NO YES
SURE? YES NO
Clear Area Information
NO - Leaves existing area information intact.
YES - Clears the area information for all areas. All areas are marked * UNUSED * and
must be renamed before being able to display on any system keypad.
2.8
OUTPUTS? NO YES
SURE? YES NO
Clear Output Information
NO - Leaves existing output information intact.
YES - Clears all programmed Output names and any output cutoff assignment.

Digital Monitoring Products XR100 Series Programming Guide
6
INITIALIZATION
XR100 Series Programming Guide Digital Monitoring Products
7
INITIALIZATION
2.9
COM/RMT? NO YES
SURE? YES NO
Clear Communication and Remote Options
NO - Leaves existing communication and remote options intact.
YES - Clears communication and remote options programming to factory defaults.
2.10
DEFAULTS NO YES
SURE? YES NO
Set to Factory Defaults
NO - Leaves existing panel programming intact.
YES - Sets the remainder of the panel programming back to the factory defaults.
Note: Sets the Programming and User language to English.

Digital Monitoring Products XR100 Series Programming Guide
8
COMMUNICATION
XR100 Series Programming Guide Digital Monitoring Products
9
COMMUNICATION
Communication
3.1
COMMUNICATION
Communication
Congure the communication options for the panel. The information you program
varies with the Communication Type you select.
3.2
COMM TYPE: DD
Communication Type
Species the communication method the panel uses to report system events to DMP
SCS-1R Receivers or non-DMP receivers. Press any Select key/area.
NONE DD NET CID
NONE - For local systems. Selecting NONE ends communication programming.
DD - Digital Dialer communications to a DMP SCS-1 or SCS-1R Receiver.
NET (Network) - Asynchronous communication using the panel onboard network
connection (XR100N). The DMP Network/Output reporting format is transmitted over
an asynchronous data network to the SCS-1 or SCS-1R Receiver. If you need to send
a duplicate signal to the central station and you have selected NET, use Receiver 2
programming to send a duplicate digital dialer signal.
Note: When NET is selected, 2ND LINE programming allows you to select D2 for two
line supervision when using a Model 893A Dual Phone Line Module.
There are extra options available if you selected NET for the communication type.
These options are explained in the following sections.
CID - This option allows the panel to communicate to non-DMP receivers using
the Ademco Contact ID format. When selected, the panel sends all of its alarm,
trouble, and supervisory reports to the receiver(s) programmed in Receiver 1 and 2
Programming.
Note: To automatically switch from DD to a backup CID receiver see Section 3.19.
3.2.1
RETRY TIME: -
Retry Time
After selecting NET, the keypad displays RETRY TIME: -. Enter the number of
seconds (3 to 15 seconds) the panel should wait before retrying to send a message
to the receiver if an acknowledgment was not received. The panel retries as many
times as possible for a period of one minute before sending a network trouble
message. For example, if retry time is set to 15, the panel retries four times. The
default Retry Time is 5 seconds.
Note: If TCP is enabled, the minimum Retry Time programmed is 6 seconds.
3.2.2
NET BCKUP NO YES
Network Backup
Select YES to enable Network Backup and require panel messages to be sent to a
backup IP Address if the messages fail to communicate to the remote (primary) IP
address. Select NO to disable Network Backup. Default is NO.
Note: When Network Backup is set to YES, a Modem Setup String is required to send
messages to a backup IP address. See Modem Setup.
Note: Second line programming is available for dialer communication types such as
CELL or DD to backup network communications.
3.2.3
SUPERVISE BACKUP
NO YES
Supervise Backup
When Network Backup is set to YES, the Supervise Backup option displays. Select
YES to enable supervised communication and send checkins to the network Central
Station receiver for Network Backup. Select NO to disable Supervise Backup. Default
is NO.
Programming options for supervision of Network Backup is provided by the same
options used by the Communications Type programming for UL AA, Check In Time,
and Fail Time. If Substitution Code is programmed YES, then it is automatically
enabled for Network Backup. When Supervise Backup is set to YES, Net Trouble
only displays on the keypad if both remote (primary) and backup IP address
communications fail.

Digital Monitoring Products XR100 Series Programming Guide
8
COMMUNICATION
XR100 Series Programming Guide Digital Monitoring Products
9
COMMUNICATION
3.2.4
RMT IP ADDRESS: -
Remote IP Address
000.000.000.000
Enter the remote (primary) IP address where the panel sends network messages.
The Remote IP Address must be unique and cannot be duplicated on the network.
Enter all 12 digits and leave out the periods. For example, enter IP address
192.168.0.250 as 192168000250. The periods display automatically.
3.2.5
ALARM PORT: -
Alarm Port
2001
Enter the receiver port number. Default port number is 2001. If a different Port
number is needed, enter the new number. Valid range is 1 to 65,535.
3.2.6
-
-
MODEM SETUP:
Modem Setup
The keypad displays MODEM SETUP:. Press COMMAND. Enter up to two lines of 16
characters to equal up to 32 characters for the backup receiver string address.
When Network Backup is set to YES, enter the backup IP address to receive panel
messages and enter a Modem Setup String.
The Modem Setup String for the Network Backup should be entered as follows:
AT#UCXXX.XXX.XXX.XXX#PPPPP. Also enter the UDP Port Number in place of the Ps.
The default port number is 2001. To enter the # (pound sign), press 0 (zero) and the
far right top row Select key. To enter . (periods), press 0 (zero) and the second from
the left Select key. Enter the backup IP Address in place of the Xs.
Note: If the onboard network interface connection J1 (XR100N only) is being used for
the main network communication (Network Backup is NO), do NOT enter a Modem
Setup String here.
To use the Network Backup and Modem Setup features to send messages through the
backup Network use the onboard network interface connection J1 on the XR100N
and assign the Modem Setup String to route the backup messages through J1 to the
backup receiver.
3.2.7
UL AA NO YES
UL AA
At the UL AA prompt, select Yes to enable AA Mode or NO to disable AA Mode. NO is
the default setting. UL AA involves check-in reports. Check-in reports are a method
of supervising the communication between the panel and the receiver. To be UL AA
compliant, panels must check-in with the receiver every 6 minutes when armed.
The SCS-1R Receiver veries that the next Check-in report is received at the
appropriate time. SCS-1/805 or higher rmware is required in the SCS-1 Receiver.
When AA is selected and the check-in fails after one minute, the panel sends a
WARNING: NETWORK TROUBLE (S72) report on the 2ND LINE. The next time the NET
report is successfully sent, the panel sends a NETWORK RESTORED (S73) report over
the 2ND LINE.
If you select YES for UL AA, the DISARM CHKIN prompt displays.
DISARM CHKIN RND
Disarm Checkin
MINUTES: - RND
Press any Select key to display Minutes: - RND. Enter the number of minutes,
from 1 to 6, between disarmed check-in reports. If any area is armed, the
report is automatically sent every 6 minutes.
To select RND (Random), press the top right Select key. RND is the default
setting. Selecting RND causes the panel to send the Check-in report at random
times. When all areas are disarmed, the panel sends the report randomly but
always between 5 to 60 minutes. If any area is armed, the panel sends the
report every 6 minutes.
Note: NET TRBL, Network Fail Notication, is automatically enabled when UL
AA is enabled. NET TRBL allows the panel to detect a primary network failure,
send an S72, Network Trouble message, through the DD if it is programmed as
the second line. When the primary network restores the panel sends an S73,
Network Restored message.

Digital Monitoring Products XR100 Series Programming Guide
10
COMMUNICATION
XR100 Series Programming Guide Digital Monitoring Products
11
COMMUNICATION
3.2.8
NET TEST NO YES
Network Test
Select YES to send an S97 network test message to the Central Station receiver over
the network based on the Test Time and frequency programmed in Communication.
Select NO to not send an S97 network test message over the network. The default is
NO.
Note: The S97 test message is specic to network operation. The S88 and S07
messages are specic to and only sent using the digital dialer. Having separate
test messages for network and digital dialer operation allows the Central Station to
identify the communication path used to send the message.
3.2.9
SUB CODE NO YES
Substitution Code
Select YES if the panel sends a Panel Substitution Code when communicating
with the receiver. The Panel Substitution Code increases the level of security
by helping to ensure that the panel sending the message to the receiver has not
been substituted by another panel. The default is NO. When UL AA is YES, the
substitution code is always sent.
When Substitution Code, Network Backup, and Supervise Backup are set to YES, the
Substitution Code is sent to both the remote (primary) and backup IP addresses.
When Substitution Code and Network Backup are set to YES and Supervise Backup is
set to NO the Substitution Code is only sent to the remote (primary) IP address.
3.2.10
CHECKIN: 6
Check In
Enter the number of minutes, from 0 to 240, between check-in reports when the
panel is armed or disarmed. Check-in reports are a method of supervising the panel
for communication with the receiver. Enter 0 (Zero) to disable the check-in. The
default is 6 minutes.
When Supervise Backup is set to YES, the Check In is sent to both the remote
(primary) and backup IP addresses. Set the Check In Time to a minimum of 3
minutes when Net Backup is set to YES. When Supervise Backup is set to NO the
Check In is only sent to the remote (primary) IP address.
Check In messages sent to the remote (primary) and backup IP addresses continue to
be sent at the same intervals over both communication paths.
Note: When used for Fire Protective Signaling, the Check-in Time should not exceed
1 minute.
3.2.11
FAIL TIME: 6
Fail Time
Entering a FAIL TIME allows the receiver to miss multiple check-ins before logging
that the panel is missing. For example, if CHECKIN is 10 and FAIL TIME is 30, the
receiver only indicates a Panel Not Responding after 30 minutes. The FAIL TIME must
be equal to or greater than the CHECKIN time: If the CHECKIN is 10 minutes, the
FAIL TIME must be 10 or more minutes. The maximum FAIL TIME is 240 minutes. The
default is 6 minutes.
3.2.12
NET TRBL NO YES
Network Trouble
Select YES to enable Network Fail Notication. When UL AA is enabled, this feature
is automatically enabled.
When NET TRBL is YES and the panel detects a primary network communication
failure, the panel attempts to send an S72, Network Trouble message, through NET
then through digital dialer when it is programmed as the second line. Also, the
trouble keypads sound a continuous tone and displays “NETWORK -TRBL.” Press any
key to silence the tone.
When the primary network restores, the panel sends an S73, Network Restored
message, through NET then through the digital dialer if it is programmed as the
second line. The “NETWORK -TRBL” display is removed from the keypad and the
tone automatically silences.