Elma Unispeed User manual

Operating Instructions
Unispeed
Polishing unit

english

Elma Schmidbauer GmbH Gottlieb-Daimler-Str. 17 D-78224 Singen Phone [phone] / 882-0 Fax [phone] / 882-266 [e-mail]
www.elma-ultrasonic.com

Contents
Contents
1General....................................................................... 3
2Important safety warnings .......................................... 3
3Product description..................................................... 4
3.1 CE conformity ............................................................. 4
3.2Designation of the elements........................................ 4
3.3 Technical details ......................................................... 5
4Putting into Operations............................................... 5
5Upkeep of the Machine .............................................. 6
6Accessory Parts/Options/Replacement Parts............. 7
7Putting out of action and waste disposal.................... 7
8Manufacturer's contact address ................................. 8
2BA_Unispeed_EN_Vers.01.2014 © Elma Schmidbauer GmbH

General
1 General
The present Operating Instructions are part of the delivered
equipment. They must be ready for use at any time and remain
with the unit in case of resale.
We reserve the right to carry out technical modifications on the
unit due to advanced development.
An operating manual cannot take account of every conceivable
use. An operating manual cannot take account of every
possible use. Contact your dealer or the manufacturer for
further information or in the event of problems which are not
covered or not sufficiently covered in this operating manual.
2 Important safety warnings
To be read before initial operation!
This polishing machine Elma Polini is intended only for
polishing metal items.
Check the unit and mains cable for transport damages. In case
of visible damages do not put the unit into operation.
For safety reasons, this electrical appliance must be connected
to a correctly grounded socket only. the technical details
indicated on the nameplate must correspond with the available
mains connection details, in particular those of the mains
voltage.
Place the unit onto a stable surface. Keep the unit dry!
Caution - risk of injury! Do not reach into rotating spindle or
polishing wheel during operation. Keep away cloths and hairs
from rotating machine parts when operating the polishing unit.
In order to prevent electrical accidents keep the working
surface, the unit and the mains plug dry!
In case of damages on the Super Elite or the mains cable do
not connect the unit to the mains!
The unit must be opened by authorized and specialized
personnel only! Unplug the mains cable before opening the unit!
Intended use
Transport damages
Mains connection
Placement
Rotary machine parts
Prevention of
electrical accidents
© Elma Schmidbauer GmbH BA_Unispeed_EN_Vers.01.2014 3

Product description
3 Product description
The professional one-work place polishing unit. Powerful
polishing with optimised dust collection system. Two speeds of
1400 / 2800 rpm. The protective cover can be folded up for
polishing large pieces. The polishing area is lighted.
3.1 CE conformity
The present Elma Super Elite complies with the relevant CE
criteria.
The declaration of conformity is available from the
manufacturer.
3.2 Designation of the elements
cover
polishing tip
gauze filter
filter drawer
screws
selector switch for engine number of revolutions
switch for lighting polishing area
switch for the exhaust
A
B
C
D
E
F
G
H
A
B
C
D
E
F
G
H
4BA_Unispeed_EN_Vers.01.2014 © Elma Schmidbauer GmbH

Putting into Operations
3.3 Technical details
Mains voltage (
as per version
) (Vac)
100-120
or
240-240
Mains frequency (Hz)
50 / 60
Max. Power Consumption (Watts)
220
Lamp (Watts)
11
Airflow Rate (m3/h)
480
Number of Revolutions (min-1)
1400/2800
External measurements W / D / H (mm)
440 x 350 x450
Weight (Kg)
30
Material of housing
Steel sheet painted
4 Putting into Operations
Compare voltage on type-plate with the voltage in your
workshop.
Place the unit onto a stable surface. Keep the unit dry!
The polishing wheel is screwed onto the polishing tip in a
clockwise direction until it has achieved the necessary
tightness. Care should be taken that the polishing wheel does
not wobble.
Connect the equipment to the mains supply. The prescribed
supply voltage can be taken from the name plate on the back of
the machine.
Switch with the right switch the exhaust in and/or out. The
exhaust should be used in principle with all polishing work
Switch the lighting of the polishing area with the left switch in
and/or out.
Once the polishing tools are mounted, you may begin with the
polishing. If larger workpieces are polished, the cover over the
polishing area can be tipped back or removed. See the section
on MAINTENANCE.
Preparation
polishing wheel
installation
Equipment at
electricity mains
attach
Blowers switch on
Lamp switch on
© Elma Schmidbauer GmbH BA_Unispeed_EN_Vers.01.2014 5

Upkeep of the Machine
5 Upkeep of the Machine
The device should be cleaned once a week. In order to allow for
a simple cleaning of the device, the shrouding cover over the
polishing area can be removed. To that end, the captivated
screw, located in the upper left area of the cover, must be
loosened. The shrouding cover can now be tipped back or, by
pushing it to the left, it can be removed from the hinges. Before
removal of the hood, the plug of the lamp must be
disconnected. The device and the interior of the shrouding
cover can now easily be cleaned with a soft cloth. When it is
heavily soiled, a mild cleaning agent can be used. To
reassemble the device, the shrouding cover is placed upon the
device and tightened down with the captivated screw. Once the
shrouding cover is remounted, the lamp must be re-connected
with the aid of the plug.
If the output of the extractor decreases markedly, the filter mat
must be changed. The filter is to be found in the filter drawer on
the front right-hand side of the machine. To change the filter
mat, the two screws are each turned a quarter rotation to the
left and the filter drawer is pulled forward out of the machine.
The old filter should be removed and the new filter inserted with
the printed side down. By emptying the gauze filter that is
located under the polishing wheel, gross detritus such as brush
hairs, etc., can be removed.
Filter met information: the filter mat in use is a fine filter and is
extremely well suited to screen out dust arising from the
polishing process. The surface is adhesive with a degree of
separation of 97% in accordance with DIN 24 185.
This filter mat is not washable. If filters capable of being washed
out are desired, they are available on request. These filter mats
belong to the coarse filter category with a filtration efficiency of
94% according to DIN 24 185. Disadvantage: fine dust particles
are not filtered out.
When the polishing wheel is being changed, the equipment
should be switched off and the plug removed.
The polishing engine does not require any attendance.
For your own safety, we recommend that you check the mains
cable and the mains connection jack at the unit for damage at
regular intervals.
There are no fuses in the machine.
In case of technical faults please contact your supplier or the
manufacturer of the unit.
Repair and maintenance works which require the unit to be
connected and opened must be carried out by authorized and
specialized personnel only.
Cleaning
Filter mat
Polishing wheel
change
Motor
Mains cable and
mains connection
Repair
Opening by
authorized
specialized
personnel only
6BA_Unispeed_EN_Vers.01.2014 © Elma Schmidbauer GmbH

Accessory Parts/Options/Replacement Parts
Separate the unit from the mains before opening up the
housing. The manufacturer cannot be held responsible for any
damage caused by unauthorized repair works.
In case of damage please contact the manufacturer or your
supplier.
6 Accessory Parts/Options/Replacement Parts
Accessories
Filter Mat Order number 3 80 02 00 013
Polishing Tip Order number 3 80 02 00 017
Options
Holder for cotton bar Order number 3 80 02 00 020
Grinding wheel set Order number 3 80 02 11 000
Connecting set central
vacuum number Order number 3 80 02 12 000
Replacement Parts:
Polishing Motor Order number 3 00 00 10 138
Capacitor 2μF Order number 3 00 00 10 173
Radial Fan 230V Order number 3 00 00 10 132
Radial Fan 115V Order number 3 00 00 10 146
Capacitor 4μF Order number 3 00 00 10 136
Appliance Switch Order number 3 00 00 10 131
Pole Switch Order number 3 00 00 10 159
Fluorescent Lamp
Ballast Order number 3 00 00 10 154
Fluorescent Tube 11W Order number 3 00 00 10 153
Holder for
Fluorescent Tube Order number 3 00 00 10 157
7 Putting out of action and waste disposal
The unit can be taken to metal and electronics recycling
stations or returned to the manufacturer.
DANGER
© Elma Schmidbauer GmbH BA_Unispeed_EN_Vers.01.2014 7

Manufacturer's contact address
8 Manufacturer's contact address
Elma Schmidbauer GmbH
Gottlieb-Daimler-Str. 17, D-78224 Singen
Phone [phone] / 882-0
Fax [phone] / 882-266
[e-mail]
www.elma-ultrasonic.com
Technical support
Phone [phone] / 882-280
Fax [phone] / 882-253
[e-mail]
Subject to technical and visual modifications Elma_ch_03/04
8BA_Unispeed_EN_Vers.01.2014 © Elma Schmidbauer GmbH