Elnapress 250S User manual

1
INSTRUCTION MANUAL
MANUAL DE INSTRUCCIONES
MANUALE D’ISTRUZIONI
OHJEKIRJA
MANUEL D’INSTRUCTIONS
INSTRUKSJONS MANUAL
BEDIENUNGSANLEITUNG
Elnapress 250S / 250SE / 450SE

LANGUAGES
ENGLISH
NORSK
ITALIANO
FRANÇAIS
DEUTSCH
ESPAÑOL
SUOMALAINEN
p. 5
p. 29
p. 53
p. 77
p. 101
p. 125
p. 149

54
TABLE OF CONTENTS
IMPORTANTSAFETYINFORMATION
ELNAPRESS 250S/250SE/450SE
ELNAPRESS 250S/250SE
ELNAPRESS 450SE
ELNAPRESS 250S
ELNAPRESS 250SE
ELNAPRESS 450SE
OPENING AND CLOSING / POWER SUPPLY
VAPOJET SYSTEM
USING THE VAPOJET
PRECAUTIONS
AFTER USE / TRANSPORT ELNAPRESS
TIPS FOR IRONING (ALL MODELS)
ACCESSORIES LIST
MAINTENANCE
OPERATE THE SLEEVE BOARD
TURN ON ELNAPRESS AND ADJUST TEMPERATURE
p. 6
p. 8
p. 10
p. 12
p. 14
p. 18
p. 19
p. 20
p. 21
p. 22
p. 24
p. 26
p. 20
p. 15
p. 16

76
IMPORTANT SAFETY INFORMATION
Read all instructions before using your Elnapress. Elnapress is reserved
exclusively for domestic use.
To avoid risk of electric shock, burns, re or personal injury:
— Lock Elnapress before moving or transporting it.
— Never immerse the press in water or other liquid.
— Carefully follow the instructions for use.
— Do not use the press if damaged; do not try to repair or disassemble it.
For repair, contact a qualied technician. Improper repair or reassembly may
cause one of the risks listed above or void the warranty.
— Never use Elnapress if the cord or press is damaged. Replace the cable
with another cable supplied by an Elnapress authorized dealer.
— Connect the press only to a grounded wall socket.
If an extension cord is needed, make sure the amperage is the one intended
for Elnapress. A cord with a lower amperage may overheat.
Use only one extension cord with grounding. Make sure that the cord is not
inadvertently pulled or mishandled.
— In case of transport, make sure that the power cord is disconnected from
the press.
— To avoid overloading the circuit, do not use another high-voltage device at
the same time.
— The cable must not touch a hot surface.
— Allow the press to cool completely before closing it and storing it.
— This appliance may be used by children over 8 years of age and by persons
with reduced physical, sensory or mental abilities or lack of experience and
knowledge if safely supervised or instructed on the use of the device and
understand the dangers involved.
— Children must not play with the appliance.
— Cleaning and maintenance of the press must not be performed by children
without supervision.
— After use, immediately unplug the plug; to remove it, pull the plug, not the
cord.
— Read the maintenance chapter before cleaning your Elnapress. There is a
risk of burns if the hot shoe is touched.
SAVE THESE INSTRUCTIONS
Welcome to the world of Elnapress.
From today ironing becomes faster, easier and more effective.
Read carefully all the instructions contained in these pages and on the website
www.elnapress.com to learn the correct use of Elnapress and its accessories.
Safety
Before using Elnapress for the rst time, read all IMPORTANT SAFETY
INSTRUCTIONS. In addition, in accordance with the recommendations made
by safety standards and organizations, disconnect the Elnapress plug when
it is left unattended, during maintenance and when parts or accessories are
replaced.
Assistance
For any information or assistance, please contact an Elnapress sales point.
The qualied staff is at your complete disposal and, by virtue of the warranty
conditions, is the only authorized person for any technical intervention.
For information and to contact the nearest dealer, consult our website
www.elnapress.com
We recommend that you keep the box and packing material of Elnapress in
order to move or transport it in maximum safety.
Generality
Subject to any changes.
This material should be stored for future reference when needed.
This ironing press corresponds to the TUV regulations.
Thank you for choosing Elnapress.

98
ELNAPRESS 250S
8
1000W/230V
1000W/120V
700W/110V
110/120v - 220/240v
50-60Hz
62 x 25 cm
(243/4 x 10 in)
10 cm (4 in)
12 kg (261/2 lb)
about 33 kg (73 lb)
65 x 541/2 x 211/2 cm
(26 x 213/4 x 81/2 in)
about 50 kg
(110 lb)
38,5 cm x 9 cm
(15,15 x 3,54 in)
2. 7.
5.
3.
4.
1.
6.
8.
11.
10.
12.
9.
9
13.
14.
15.
MAIN PARTS
1. Heating shoe.
2. Ironing board (complete with
padding).
3. Fixed handle (to raise and lower
the heating shoe).
4. Mobile handle (to exert automatic
pressure).
5. Safety lock (slide button to the
left to lock and transport the press).
6. Socket for power plug connection.
7. Sleeve Board.
8. ON/OFF switch to turn the press on/off.
9. Temperature regulator.
10. Heating indicator (red light).
11. Switching on light (green light).
12. Electronic safety signal.
13. Ironing cushion.
14. Vapojet (optional).
15. Elnapress dust cover (optional).
Total pressure
developed
Height from the base
Weight
Mini pressure
Overall
dimensions
Dimensions of the
Small sleeve board
TECHNICAL SPECIFICATIONS
Power
consumption
Voltage
Dimensions of the
ironing board

1110
ELNAPRESS 250SE
10
2. 7.
5.
3.
4.
1.
6.
8.
11.
10.
12.
9.
11
13.
14.
15.
Total pressure
developed
1000W/230V
1000W/120V
700W/110V
62 x 25 cm
(243/4 x 10 in)
Height from the base 10 cm (4 in)
Weight 12 kg (261/2 lb)
Mini pressure about 22-33kg
(73 lb)
Overall
dimensions 65 x 541/2 x 211/2 cm
(26 x 213/4 x 81/2 in)
about 50 kg
(110 lb)
Dimensions of the
large sleeve board 55 x 11 cm
(21,85 x 4,33 in)
TECHNICAL SPECIFICATIONS
Power
consumption
Voltage 110/120v - 220/240v
50-60Hz
Dimensions of the
ironing board
MAIN PARTS
1. Heating shoe.
2. Ironing board (complete with
padding).
3. Fixed handle (to raise and lower
the heating shoe).
4. Mobile handle (to exert automatic
pressure).
5. Safety lock (slide button to the
left to lock and transport the press).
6. Socket for power plug connection.
7. Sleeve Board.
8. ON/OFF switch to turn the press on/off.
9. Temperature regulator.
10. Heating indicator (red light).
11. Switching on light (green light).
12. Electronic safety signal.
13. Ironing cushion.
14. Vapojet (optional).
15. Elnapress dust cover (optional).

13
13.
11.
14.
15.
12
ELNAPRESS 450SE
2.
5.
3.
8.
4.
1.
6.
12.
9.
10.
7.
11.
Total pressure
developed
1000W/230V
1000W/120V
700W/110V
62 x 25 cm
(243/4 x 10 in)
Height from the base 10 cm (4 in)
Weight 12 kg (261/2 lb)
Mini pressure 22-33kg
about 50 kg
(110 lb)
Overall
dimensions 65 x 541/2 x 211/2 cm
(26 x 213/4 x 81/2 in)
Dimensions of the
Large sleeve board 55 x 11 cm
(21,85 x 4,33 in)
TECHNICAL SPECIFICATIONS
Power
consumption
Voltage 110/120v - 220/240v
50-60Hz
Dimensions of the
ironing board
1. Heating shoe.
2. Ironing board (complete with
padding).
3. Fixed handle (to raise and lower the
heating shoe).
4. Mobile handle (to exert automatic
pressure).
5. Safety lock (slide button to the left to
lock and transport the press).
6. Socket for power plug connection.
7. Electronic security signal.
8. Sleeve Board.
9. Touch button (digital pressure) to
switch on and set the ironing
program (+ increase the temperature).
10. Touch button (digital pressure) to
switch off and set the ironing program
(- decrease the temperature).
11. Digital indicator lights ironing
program (Nylon - Silk - Mesh - Cotton
/“Optimal Temperature”).
12. Heating indicator (red light).
13. Vapojet.
14. Ironing cushion.
15. Elnapress dust cover (optional).
MAIN PARTS

1514
OPENING AND CLOSING
POWER SUPPLY
Slide the safety lock to the right to unlock Elnapress.
Place the left hand on the xed handle and the right hand on the movable
handle.
Raise the movable pressure lever with the right hand and accompany it until
the maximum opening and at the same time exert, with the left hand, a slight
downward force on the handle of the xed lever.
Release the right-hand grip by releasing the movable handle.
Accompany the heating shoe with the left hand towards the maximum opening.
Once the garment to be ironed has been placed on the board, place the left
hand on the xed handle and exert a downward pressure until the heating
shoe gets in contact with the board.
Hold the movable lever with your right hand and move it down. By bringing
the lever to maximum closing, maximum pressure is exerted. To obtain the
mini pressure, bring the lever to approximately half of its stroke. If necessary,
repeat the same movement several times.
N.B. If the Vapojet is inserted into the xed handle, always keep your left hand
close to the lever. The left hand must never cover the word “Vapojet” on the
component.
Open the press. The rating plate, located
under the base, shows the voltage and
serial number. Make sure the voltage
matches that of your home.
Connect the plug of the power cable to the
plug of the press. Insert the plug of the
cable into the wall socket.
N.B. Elnapress must be connected to
a wall socket, grounded only. Read the
safety regulations carefully.
ELNAPRESS 250S/250SE
With the press still open, press the digital pressure on/off button. The green and red
lights will illuminate to indicate that the press is on and warming up.
Turn the temperature regulator up to the desired level.
When the right temperature is reached, the red light will switch off.
To switch off the press, press lightly on the digital pressure switch again.
N.B: If the press is closed, the temperature cannot be adjusted.
IRONING TEMPERATURES
nylon - silk wool cotton
Before ironing the garment, check that
the symbols on its label correspond to the
temperature adjustment mode.
TURN ON ELNAPRESS AND
ADJUST TEMPERATURE
15

171616
ELNAPRESS 450SE
Slightly press the ON button with the press open.
A red light will illuminate.
At the same time the icon will light up green:
Select the desired ironing program by pressing the + button several times.
Elnapress 450SE is able to manage two different temperature modes:
1. Manual in nylon, silk, wool mode
2. Using the new “Optimal Temperature” function. The function is activated
automatically when “cotton” mode is selected.
The two icons will light up simultaneously:
Cotton - Optimal Temperature.
The function allows you to be able to iron garments of different composition without
having to worry about the temperature regulation. For some newly designed fabrics,
such as garments that use chemical bers, we recommend doing an ironing test
(lowering and raising the pressure lever quickly) in a small area, ensuring that
the temperature cannot damage your garment. If the garment tends to rise from
the ironing board, we recommend entering manual mode by selecting a more
appropriate program (always check the temperatures indicated on the label of your
garment). When the right temperature is reached, the red light will switch off.
To switch off the press, repeatedly press the off button until you switch off all the
lights/bright icons.
N.B: If the press is closed, the temperature can only be lowered.
IRONING TEMPERATURES
nylon - silk wool cotton -
optimal temp.
Before ironing the garment, check that
the symbols on its label correspond to the
temperature adjustment mode.
TURN ON ELNAPRESS AND
ADJUST TEMPERATURE
SAFETY FEATURES
All models are equipped with a blocking mechanism ensuring a safe transport.
If by lack of attention the press should remain closed for more than ten
seconds, a double electronic safety system will trigger an acoustic signal
“beep-beep” which will interrupt the electrical circuit and will be reactivated
automatically by re-opening the press.
INSTRUCTIONS FOR ALL MODELS
ELNAPRESS 250S / 250SE / 450SE
If Elnapress is left on when it is open and not used for 15 minutes, the
electric current is switched and the press will automatically be turned off
by sending a sound “beep-beep” signal. To reactivate it, press the power
button.
ELNAPRESS 450SE
At each automatic or manual switch-off, the software checks all its functions.
If after 45 min the temperature is still = /> 65°, the safety system will block all
the functionalities to safeguard your product and the environment where you
are ironing. The display will light up again and warn you by sending a sound
“beep beep” signal
The system can NOT be restored and reset by simply switching off (Off button)
your ironing press.
Once you have noticed the anomaly, please follow the instructions below:
1. Switch off the press with the appropriate button (see switch-off instructions)
2. Disconnect the cable from the product (if it is still connected)
Contact an Elnapress authorized service center (refer to our website
www.elnapress.com).

1918
Elnapress is equipped with an exclusive Vapojet system for the formation of
natural steam.
The Vapojetet allows to spray simple tap water directly on the items to be
ironed. The natural vaporization combined with the automatic pressure and
the heating shoe heat regenerate the bers of the fabric in depth.
The (force of) natural vaporization is obtained by combining the vaporization
of the Vapojet, with the forces exerted by the Elnapress ironing board, the
automatic pressure and the heat of the heating shoe.
This combination of forces and elements are formed directly inside your
garments and in addition to obtaining an impeccable ironing quality without
any effort, it is able to regenerate the bers of the fabric in depth enhancing
the colors and safeguarding them from aging.
The Vapojet operates without any electricity consumption.
N.B. Do not put starch in the water.
VAPOJET SYSTEM
To remove the Vapojet, simply slide it out of the xed handle.
1) Remove the cap and ll it with about ¾ of water.
Do not completely ll the Vapojet.
2) Replace the cap and slide the Vapojet onto the xed handle. Press the lever
rst slowly, then faster until nebulization. Now it’s ready to use.
If at rst use after following step 2 your Vapojet does not nebulize we
recommend:
1. Carefully check that the cap closure is correct. In case open and close again.
2. Position the Vapojet vertically, directly under the sink tap and with the cap
facing upwards.
Open the cap and start the water lling procedure. While lling and remaining
in a vertical position, press the Vapojet lever repeatedly until nebulization.
When in operation, close the cap and hook the Vapojet to your press.
3) Place the garments on the board, spray the Vapojet lever several times and
lower the heating shoe to create natural steam.
N.B: you can perform the spraying operation even while you are lowering the
heating shoe.
1)
USING THE VAPOJET
2)
3)

2120
PRECAUTIONS
OPERATE THE SLEEVE BOARD
— Remove the vaporizer from the handle when you stop or nish ironing.
— Place Vapojet vertically (cap below) to prevent drops of water from falling.
— Empty the vaporizer after use.
— At the end of ironing, close and open the still warm press for a few times,
without linen, to dry and protect the cover and the padding.
— Do not put starch in the water.
ELNAPRESS 250 / 450 / 450SE
Place your hands on the surface of the Sleeve board and rotate it upwards.
Once the locking device is activated, at the stroke end press rmly until you
hear the click.
20
AFTER USE
TRANSPORT ELNAPRESS
Turn off Elnapress following the instructions on page 15-16.
Remove and empty the Vapojet. While the press is still hot, open it and close
it several times to let the board cover and foam padding dry. Leave the press
open until it is completely cold.
As mentioned in the “Safety Features” section if the press is switched off and
closed while the plug is still inserted, a safety alarm will be triggered if the
specic internal “product safeguard” sensor detects a temperature = /> 65°
after 45 min. from its switching off.
N.B. Do not close or block the press before it has cooled.
This operation is only possible if the optional accessory “Protective sheet” is
used (see accessories list page. 24-25).
Always close the press and lock it with the appropriate safety hook before
moving it. To store it, take it by the xed handle.

2322
TIPS FOR IRONING (ALL MODELS)
There are cases in which special attention must be paid to the labels of your
garments, as usually happens with an iron.
We recommend ironing all clothes slightly damp.
PREPARE THE LINEN
MINI PRESSURE
We recommend starting with the lowest temperatures, to rst iron the delicate
items and increase temperature according to the fabrics.
We recommend that you properly lay out your garments on the ironing board
by manually attening any unwanted creases formed after insertion and/or
placement of clothing.
Simply move your hands horizontally on the ironing board, thus avoiding
touching the heating shoe.
Leave the press closed for a few seconds to press the garment.
If the shoe is closed for more than ten seconds, the electronic safety alarm
will trigger and the current will automatically stop. When the press is opened,
the current will reactivate.
N.B: The “beep-beep” is a safety device device that comes into operation if
the press remains closed for more than 10 seconds and is NOT a heating shoe
opening signal.
Two Elnapress golden rules:
1. Get used to correctly positioning the item in the large space behind the
ironing board.
2. Always move the item forward towards you.
Some fabrics do not require total pressure. By lowering the movable handle,
about halfway or less, you can apply a mini pressure. If necessary, repeat the
operation several times. Use mini pressure for delicate fabrics such as: wool,
velvet, applications, ties, etc.
INTEGRATED SLEEVE BOARD
IRONING CUSHION
BUTTONS, ZIPPERS, PINS
It is useful for ironing baby clothes, shirt cuffs, folds, pockets, yokes, etc.
Thanks to its particular shapes it replaces and improves the performance of
the tip of an iron.
The cushion is used for ironing the most difcult points and/or perfect the
ironing of details such as darts, collars, cuffs, seams, buttons, zippers etc. It
can be inserted in one end of the sleeve board or be placed on the large board,
inserted inside the items or used by inserting the hand inside the lining placed
in the lower part of the cushion and positioning the item on the upper surface,
rubbing it directly onto the heating shoe to iron and/or retouch some points
of the item.
The padded ironing board allows the buttons to sink into the padding without
breaking.
Be careful not to use too high a temperature that can melt synthetic material.
If you are not sure, put the item upside down.
Never put in contact mother-of-pearl buttons with the heating shoe.

2524
ACCESSORIES LIST
VAPOJET
PADDING FOAM
SLEEVE BOARD
COVER LARGE
SLEEVE BOARD
COVER SMALL
IRONING CUSHION
(WITH DOUBLE LINING FOR HANDLE)
SPRAY BOTTLE
IRONING COVER
CLEANING KIT: CLEANING LIQUID
+ HEATING SHOE PROTECTION LIQUID
HEATING SHOE
PROTECTION LIQUID
LONG CUSHION
PROTECTION SHEET
POWER CORD
DUST COVER

2726
By continuously using your ironing press, the padding attens and the ironing
is no longer impeccable; therefore, it is necessary to replace the foam and the
board cover when they are worn (see accessories list).
Important: Use only original Elnapress accessories.
The covers can be washed at 30°C.
The heating shoe requires simple cleaning. We recommend at each use,
before turning off the machine, to pass a soft cloth over the entire surface of
the shoe.
For cleaning your press, you must use only Elnapress “cleaning liquid” that
you will nd among the various accessories that can be purchased separately.
Never use cleaning products other than this specic one or steel wool pads
or abrasive products.
To clean the heating shoe with Elnapress “cleaning liquid”:
— Turn on Elnapress, position the temperature on silk. Once the temperature
has been reached, disconnect the electric cable directly from the press.
— Turn the press over on a level, so that the heating shoe looks towards you.
Be careful that the cover is not scratched.
— Spread the cleaning liquid with a microber cloth and wipe the entire shoe
surface. Once nished remove the halos from the shoe by wiping with a dry
micro-ber cloth.
— After cleaning the heating shoe, recreate a thin layer of protection using
the “Heating shoe protection liquid” (optional accessory) on the surface of
the shoe.
Switch on and position at maximum temperature.
Spread the stick in the highest part of the shoe, still upside down, and during
the descent towards the lower part spread the liquid over the entire surface of
the shoe with a soft or microber cloth.
Wait for the automatic shut-off. After cleaning we recommend using a
protection between the shoe and the cover board to avoid possible stains.
MAINTENANCE
PADDING AND IRONING COVER FOR THE BOARD
CLEANING OF THE HEATING SHOE

SOMMARIO
IMPORTANTI INFORMAZIONI DI SICUREZZA
ELNAPRESS 250S/250SE/450SE
ELNAPRESS 250S/250SE
ELNAPRESS 450SE
ELNAPRESS 250S
ELNAPRESS 250SE
ELNAPRESS 450SE
APERTURA E CHIUSURA / ALIMENTAZIONE
SISTEMA VAPOJET
UTILIZZO DEL VAPOJET
PRECAUZIONI
DOPO L’USO / TRASPORTARE ELNAPRESS
CONSIGLI PER STIRARE (TUTTI I MODELLI)
LISTA ACCESSORI
MANUTENZIONE
AZIONARE LO STIRAMANICHE
ACCENDERE ELNAPRESS E REGOLARE LA TEMPERATURA
p. 30
p. 32
p. 34
p. 36
p. 38
p. 42
p. 43
p. 44
p. 45
p. 46
p. 48
p. 50
p. 44
p. 39
p. 40

3130
IMPORTANTI INFORMAZIONI DI SICUREZZA
Leggere tutte le istruzioni prima di utilizzare la pressa da stiro Elnapress.
Elnapress è riservata ad uso esclusivamente domestico.
Per evitare rischi di scossa elettrica, ustioni, incendio o lesioni personali:
— Bloccare Elnapress prima di spostarla o trasportarla.
— Non immergere mai la pressa in acqua o altro liquido.
— Seguire attentamente le istruzioni per l’uso.
— Non utilizzare la pressa se danneggiata; non cercare di ripararla o smontarla.
Per la riparazione rivolgersi a un tecnico qualicato.
Una riparazione o un rimontaggio sbagliati potrebbero provocare uno dei
rischi sopra elencati o far decadere la garanzia.
— Non usare mai Elnapress se il cavo o la pressa sono danneggiati.
Sostituire il cavo con un altro fornito da un rivenditore autorizzato Elnapress.
— Collegare la pressa solo a una presa a muro con messa a terra.
Se fosse necessario l’uso di una prolunga, assicurarsi che l’amperaggio sia
quello previsto per Elnapress. Un cavo con un amperaggio inferiore potrebbe
surriscaldarsi. Utilizzare solo una prolunga con la messa a terra.
Assicurarsi che il cavo non venga inavvertitamente tirato o maltrattato.
— In caso di trasporto, assicurarsi che il cavo di alimentazione sia scollegato
dalla pressa.
— Per evitare un sovraccarico del circuito non usare contemporaneamente
un altro apparecchio ad alto voltaggio.
— Il cavo non deve toccare una supercie calda.
— Lasciare raffreddare completamente la pressa prima di chiuderla e riporla.
— Questo apparecchio può essere utilizzato da bambini di età superiore a
8 anni e da persone con ridotte capacità siche, sensoriali o mentali con
mancanza di esperienza e conoscenza se sono sorvegliati oppure se hanno
ricevuto istruzioni riguardo l’utilizzo in sicurezza dell’apparecchio e se ne
hanno capito i pericoli implicati.
— I bambini non devono giocare con l’apparecchio.
— La pulizia e la manutenzione della pressa non devono essere eseguite da
bambini senza supervisione.
— Dopo l’uso, disinserire immediatamente la spina; per toglierla, tirare la
spina stessa e non il cavo.
— Leggere il capitolo relativo alla manutenzione prima di pulire la vostra
Elnapress. Vi è rischio di ustioni se si tocca la piastra ancora calda.
CONSERVATE QUESTE ISTRUZIONI
Benvenuto nel mondo di Elnapress.
Da oggi stirare diventa più veloce, più facile e più efcace.
Leggete attentamente tutte le istruzioni contenute in queste pagine e sul sito
www.elnapress.com per apprendere il corretto utilizzo di Elnapress e dei suoi
accessori.
Sicurezza
Prima di utilizzare Elnapress per la prima volta, leggere tutte le IMPORTANTI
ISTRUZIONI DI SICUREZZA. Inoltre, conformemente alle raccomandazioni
fatte dagli standard e dalle organizzazioni che si occupano di sicurezza,
disinserire la spina di Elnapress quando la si lascia incustodita, durante la
manutenzione e quando vengono sostituiti dei pezzi o degli accessori.
Assistenza
Per qualsiasi informazione o per ricevere assistenza si prega di rivolgersi
a un punto vendita Elnapress. Il personale qualicato è a Vostra completa
disposizione, nonché, in virtù delle condizioni di garanzia, è l’unico autorizzato
per qualsiasi intervento tecnico.
Per avere informazioni e contattare il rivenditore più vicino, consultate il
nostro sito internet www.elnapress.com
Si raccomanda di conservare la scatola e il materiale di imballaggio di
Elnapress per spostarla o trasportarla nella massima sicurezza.
Generalità
Con riserva di eventuali modiche.
Questo materiale deve essere conservato per consultarlo quando necessario.
Questa pressa da stiro corrisponde alle normative TUV.
Grazie per aver scelto Elnapress.

3332
ELNAPRESS 250S
32
SPECIFICHE TECNICHE
Potenza assorbita
Pressione totale
sviluppata
1000W/230V
1000W/120V
700W/110V
Voltaggi 110/120v - 220/240v
50-60Hz
Dimensione
dell’asse da stiro 62 x 25 cm
(243/4 x 10 in)
Altezza dalla base 10 cm (4 in)
Peso 12 kg (261/2 lb)
Mini pressione circa 33 kg (73 lb)
Dimensioni
totali 65 x 541/2 x 211/2 cm
(26 x 213/4 x 81/2 in)
circa 50 kg
(110 lb)
Dimensioni dello
stiramaniche piccolo 38,5 cm x 9 cm
(15,15 x 3,54 in)
2. 7.
5.
3.
4.
1.
6.
8.
11.
10.
12.
9.
33
13.
14.
15.
PARTI PRINCIPALI
1. Piastra scaldante.
2. Asse da stiro (completo di
imbottitura).
3. Impugnatura ssa (per alzare e
abbassare la piastra scaldante).
4. Impugnatura mobile (per esercitare
la pressione automatica).
5. Chiusura di sicurezza (spostare
a sinistra il pulsante per bloccare e
trasportare la pressa).
6. Presa per innesto spina
alimentazione.
7. Stiramaniche.
8. Tasto di accensione e spegnimento
touch (pressione digitale).
9. Regolatore di temperatura.
10. Spia di riscaldamento (luce rossa).
11. Spia di accensione (luce verde).
12. Segnale di sicurezza elettronico.
13. Cuscino per stirare.
14. Vapojet (opzionale).
15. Borsa Elnapress (opzionale).

3534
ELNAPRESS 250SE
SPECIFICHE TECNICHE
Potenza assorbita
Pressione totale
sviluppata
1000W/230V
1000W/120V
700W/110v
Voltaggi 110/120v - 220/240v
50-60Hz
Dimensione
dell’asse da stiro 62 x 25 cm
(243/4 x 10 in)
Altezza dalla base 10 cm (4 in)
Peso 12 kg (261/2 lb)
Mini pressione circa 22-33kg (73 lb)
Dimensioni
totali 65 x 541/2 x 211/2 cm
(26 x 213/4 x 81/2 in)
circa 50 kg
(110 lb)
Dimensioni dello
stiramaniche grande 55 x 11 cm
(21,85 x 4,33 in)
PARTI PRINCIPALI
34
2. 7.
5.
3.
4.
1.
6.
8.
11.
10.
12.
9.
35
13.
14.
15.
1. Piastra scaldante.
2. Asse da stiro (completo di
imbottitura).
3. Impugnatura ssa (per alzare e
abbassare la piastra scaldante).
4. Impugnatura mobile (per esercitare
la pressione automatica).
5. Chiusura di sicurezza (spostare
a sinistra il pulsante per bloccare e
trasportare la pressa).
6. Presa per innesto spina
alimentazione.
7. Stiramaniche.
8. Tasto di accensione e spegnimento
touch (pressione digitale).
9. Regolatore di temperatura.
10. Spia di riscaldamento (luce rossa).
11. Spia di accensione (luce verde).
12. Segnale di sicurezza elettronico.
13. Cuscino per stirare.
14. Vapojet (opzionale).
15. Borsa Elnapress (opzionale).

3736 37
13.
11.
14.
15.
Potenza assorbita
Pressione totale
sviluppata
1000W/230V
1000W/120V
700W/110V
Voltaggi 110/120v - 220/240v
50-60Hz
Dimensione
dell’asse da stiro 62 x 25 cm
(243/4 x 10 in)
Altezza dalla base 10 cm (4 in)
Peso 12 kg (261/2 lb)
Mini pressione 22-33kg
circa 50 kg
(110 lb)
Dimensioni
totali 65 x 541/2 x 211/2 cm
(26 x 213/4 x 81/2 in)
Dimensioni dello
stiramaniche grande 55 x 11 cm
(21,85 x 4,33 in)
SPECIFICHE TECNICHE PARTI PRINCIPALI
1. Piastra scaldante.
2. Asse da stiro (completo di
imbottitura).
3. Impugnatura ssa (per alzare e
abbassare la piastra scaldante).
4. Impugnatura mobile (per
esercitare la pressione automatica).
5. Chiusura di sicurezza (spostare
a sinistra il pulsante per bloccare e
trasportare la pressa).
6. Presa per innesto spina
alimentazione.
7. Segnale di sicurezza elettronico.
8. Stiramaniche.
9. Tasto touch (a pressione digitale)
di accensione e di impostazione
del programma di stiratura (+
aumentare la temperatura).
10. Tasto touch (a pressione digitale)
di spegnimento e di impostazione
del programma di stiratura (-
diminuire la temperatura).
11. Spie digitali programma di stiratura
(Nylon - Seta - Maglia - Cotone /
“Optimal Temperature”).
12. Spia di riscaldamento (luce rossa).
13. Vapojet.
14. Cuscino per stirare.
15. Borsa Elnapress (opzionale).
36
ELNAPRESS 450SE
2.
5.
3.
8.
4.
1.
6.
12.
9.
10.
7.
11.

3938
ELNAPRESS 250S/250SE
Con la pressa ancora aperta, premere il tasto di accensione e spegnimento a
pressione digitale. Si illumineranno le spie verde e rossa per indicare che la pressa
è accesa e si sta riscaldando.
Girare il regolatore di temperatura no al livello desiderato.
Raggiunta la giusta temperatura la luce rossa si spegnerà.
Per spegnere la pressa, esercitare nuovamente una leggera pressione sul tasto di
accensione a pressione digitale.
N.B: Se la pressa è chiusa la temperatura non può essere regolata.
TEMPERATURE DI STIRATURA
nylon - seta lana cotone
Prima di stirare il capo di abbigliamento,
controllate che i simboli sulla sua
etichetta corrispondano alla modalità di
regolazione della temperatura.
APERTURA E CHIUSURA
ALIMENTAZIONE
Far scivolare la chiusura di sicurezza verso destra per sbloccare Elnapress.
Posizionare la mano sinistra sull’impugnatura ssa e la mano destra
sull’impugnatura mobile.
Alzare con la mano destra la leva mobile di pressione accompagnandola sino
alla massima apertura, esercitando contemporaneamente con la mano sinistra
una leggera forza verso il basso sull’impugnatura della leva ssa.
Lasciare la presa della mano destra liberando l’impugnatura mobile.
Accompagnare con la mano sinistra la piastra verso la massima apertura.
Una volta sistemato sull’asse l’indumento da stirare, portare la mano sinistra
sull’impugnatura ssa ed esercitare una pressione verso il basso no a portare
a contatto la piastra con l’asse.
Impugnare con la mano destra la leva mobile e accompagnarla verso il basso.
Portando la leva a massima chiusura si esercita la pressione massima. Per
ottenere la mini pressione portare la leva a circa metà della sua corsa.
Se necessario ripetere più volte lo stesso movimento.
N.B. Se Vapojet è inserito sull’impugnatura ssa, tenere sempre la mano
sinistra in prossimità della leva. La mano sinistra non deve mai coprire la
parola “Vapojet” presente sul componente.
Aprire la pressa. La targhetta delle
caratteristiche, situata sotto la base,
mostrailvoltaggioeilnumerodimatricola.
Assicurarsi che il voltaggio corrisponda a
quello della vostra abitazione.
Collegare la spina del cavodi alimentazione
alla spina di innesto della pressa. Inserire
la spina del cavo nella presa a muro.
N.B. Elnapress deve essere collegata
a una presa a muro, solo con messa a
terra. Leggere attentamente le norme di
sicurezza.
ACCENDERE ELNAPRESS E
REGOLARE LA TEMPERATURA
39