Elumen8 ELUM023 User manual

Order codes: ELUM023
Evora 1000 Spot
User Manual

www.prolight.co.uk Evora 1000 Spot User Manual 2
Safety advice
WARNING
FOR YOUR OWN SAFETY, PLEASE READ THIS USER MANUAL
CAREFULLY BEFORE YOUR INITIAL START-UP!
• Before your initial start-up, please make sure that there is no damage caused during transportation.
• Should there be any damage, consult your dealer and do not use the equipment.
• To maintain the equipment in good working condition and to ensure safe operation, it is necessary
for the user to follow the safety instructions and warning notes written in this manual.
• Please note that damages caused by user modications to this equipment are not subject to warranty.
IMPORTANT:
The manufacturer will not accept liability for any resulting damages caused by the non-observance
of this manual or any unauthorised modication to the equipment.
CAUTION!
KEEP THIS EQUIPMENT
AWAY FROM RAIN,
MOISTURE AND LIQUIDS
CAUTION!
TAKE CARE USING
THIS EQUIPMENT!
HIGH VOLTAGE-RISK
OF ELECTRIC SHOCK!!
• Never let the power cable come into contact with other
cables. Handle the power cable and all mains voltage
connections with particular caution!
• Never remove warning or informative labels from the unit.
• Do not open the equipment and do not modify the unit.
• Do not connect this equipment to a dimmer pack.
• Do not switch the equipment on and off in short intervals,
as this will reduce the system’s life.
• Only use the equipment indoors.
• Do not expose to ammable sources, liquids or gases.
• Always disconnect the power from the mains when
equipment is not in use or before cleaning! Only handle
the power-cable by the plug. Never pull out the plug by
pulling the power-cable.
• Make sure that the available mains supply voltage is
between 100~240V AC, 50/60Hz.
• Make sure that the power cable is never crimped or
damaged. Check the equipment and the power cable
periodically.
• If the equipment is dropped or damaged, disconnect the
mains power supply immediately and have a qualied
engineer inspect the equipment before operating again.
• If the equipment has been exposed to drastic
temperature uctuation (e.g. after transportation),
do not connect power or switch it on immediately.
The arising condensation might damage the equipment.
Leave the equipment switched off until it has reached
room temperature.
• If your product fails to function correctly, stop use
immediately. Pack the unit securely (preferably in the
original packing material), and return it to your Prolight
dealer for service.
• Only use fuses of same type and rating.
• We recommend this xture should be serviced at least
once every 3 months to prevent build-up of dust, dirt and
debris that could affect the xtures operation.
• Repairs, servicing and power connection must only be
carried out by a qualied technician. THIS UNIT CONTAINS
NO USER SERVICEABLE PARTS.
• This lighting xture is for professional use only - it is
not designed for or suitable for household use. The
product must be installed by a qualied technician in
accordance with local territory regulations. The safety of
the installation is the responsibility of the installer. The
xture presents risks of severe injury or death due to re
hazards, electric shock and falls.
• Warning! Risk Group 2 LED product according to
EN 62471. Do not view the light output with optical
instruments or any device that may concentrate the beam.
• WARRANTY: Two years from date of purchase.
OPERATING DETERMINATIONS
If this equipment is operated in any other way,
than those described in this manual, the product
may suffer damage and the warranty becomes void.
Incorrect operation may lead to danger
e.g: short-circuit, burns and electric shocks etc.
Do not endanger your own safety and the safety
of others!
Incorrect installation or use can cause serious damage
to people and/or property.

www.prolight.co.uk Evora 1000 Spot User Manual 3
Product overview & technical specications
The Evora 1000 Spot features super smooth 3 phase motors and a host of features making this an ideal xture for
larger events and venues. The 180W LED and colour wheel coupled with a 3 facet, indexable rotating prism plus 5
facet linear rotating indexable prism and remote focus produce rich vibrant colours and 2 gobo wheels (9 static and
7 rotating) provide a host of superb animated effects. Pan/tilt auto correction and
16 bit positioning make this xture perfect for rental and installation alike.
• 1 x 180W white LED
• Beam angle: 12°
• 44,100 Lux @ 2m
• 3.6kHz refresh rate
• Motorised focus
• 3 facet circular rotating indexable prism
plus 5 facet linear rotating indexable prism
• Frost lter
• Gobo wheel 1: 7 rotating, indexable,
replaceable gobos + open
• Gobo wheel 2: 9 static gobos + open
• Colour wheel: 7 colours + open
• DMX channels: 15
• RDM (Remote Device Management)
• Auto, sound active and master/slave modes
• Pan/tilt auto correction
• 16-Bit pan/tilt positioning
• Pan: 540°, Tilt: 270°
• 0-100% dimming and variable strobe
• Supplied with quick release omega clamps
• 6 push button menu with 1.8” LCD display
• PowerCON input/output
• 3-Pin XLR input/output
• 5-Pin XLR input/output
• Fan cooled
Evora 1000 Spot
Specications Evora 1000 Spot
Power consumption 290W
Fuse T4A 250V
Power supply 100~240V, 50/60Hz
Dimensions 560 x 390 x 290mm
Weight 16.4kg
Order code ELUM023
0m 1m 2m 3m 4m 5m
12° - Lux 176000 44100 19560
12°
11000 7060
560mm
390mm 290mm

www.prolight.co.uk Evora 1000 Spot User Manual 4
Technical specications
01 - Earth point
02 - LCD display
03 - Function buttons
04 - Microphone
05 - 3-Pin DMX input
06 - 3-Pin DMX output
07 - 5-Pin DMX input
08 - 5-Pin DMX output
09 - PowerCON input
10 - PowerCON output
11 - Fuse T4A 250V
12 - Fans
In the box: 1 x xture,
2 x omega clamps,
1 x power cable
& 1 x user manual
POWER INPUT:
100-240V~50/60Hz
FUSE: T4A 250V
3-PIN DMX INPUT
5-PIN DMX INPUT
3-PIN DMX OUTPUT
5-PIN DMX OUTPUT
100-240V~50/60Hz
POWER OUTPUT:
POWER CONSUMPTION: 290W
DISPLAY BACKUP MIC
MENU UP
LEFT ENTER RIGHT
DOWN
Evora 1000 Spot
12
07
05
11
02 03 12 01 10 08
09 06
04
12

www.prolight.co.uk Evora 1000 Spot User Manual 5
Rotating Gobo Replacement:
The xture is supplied with 7 rotating, replaceable gobos. See below for installation instructions.
1) Disconnect and isolate from power then place the
xture on a at surface and unscrew the head shell.
2) Remove the head shell including the safety wire
xed to the metal head plate.
3) Carefully remove one of the gobo trays by
lifting slightly and pulling towards you releasing the
tray from the spring clip.
4) Now you can remove the circlip, followed by the
gobo from the gobo tray. Replace the gobo and t
the circlip back into the tray.
5) Place the gobo tray back into
the gobo wheel by sliding it back
under the spring clip and pushing
it down into the wheel.
6) Fasten the safety wire from the
shell back onto the metal head
plate.
7) Tighten the screws until the
head shell is secure.
Rotating Gobo Replacement

www.prolight.co.uk Evora 1000 Spot User Manual 6
Operating instructions
Control Panel Menu:
The LCD control panel situated on the front of the xture allows the user to access the menu system to
adjust the xtures settings.
When the unit has been powered on it will show “Software Update Please Wait...” followed by “Motor
Reset Please Wait...” and “eLumen8 Evora 1000 Spot”. The xture will then return to its home screen.
Pressing the “MENU” button once will take the user to the xtures main menu. Using the “UP” and
“DOWN” buttons you can then navigate between the different options in the main menu. Pressing the
“ENTER” button on one of these options allows you to access the sub menu where you can use the
“LEFT” and “RIGHT” buttons to select option/value required. Once the option/value has been selected
press the “ENTER” button once more to conrm the setting.
To exit out of any of the above options, press and hold the “MENU” button.
The LCD control panel can be used via the internal battery. To access this press and hold the
“DISPLAY BACKUP” button for 5 seconds until the xtures home screen is displayed. The LCD
display will automatically shut off after 20 seconds of inactivity.
Error Codes:
When the unit is powered on the unit will automatically perform a motor reset. If there is a problem with
one or more of the motors the display will ash 5 times and display “pan/tilt error” on the LCD control
panel. Please power the unit off and on to reset the motors again.
DISPLAY BACKUP MIC
MENU UP
LEFT ENTER RIGHT
DOWN
Evora 1000 Spot
Offset Menu:
To access the units offset menu
press the “MENU” button once
to display “DMX Address” on the
LCD display. Press and hold the
“ENTER” button until the offset
menu is displayed.
Offset Menu Options/Values
(Default Settings in BOLD)
Description
Pan Offset -128-127 (000) Pan Offset
Tilt Offset -128-127 (000) Tilt Offset
Color Offset -128-127 (000)Color Offset
Gobo1 Offset -128-127 (000) Gobo Wheel 1 Offset
RGobo1 Offset -128-127 (000) Gobo Wheel 1 Rotation Offset
Gobo2 Offset -128-127 (000) Gobo Wheel 2 Offset
Prism Offset 000-255 (000) Prism Offset
RPrism Offset -128-127 (000) Prism Rotation Offset
Focus Offset 000-255 (000) Focus Offset

www.prolight.co.uk Evora 1000 Spot User Manual 7
Operating instructions
Main Menu Sub Menu Options/Values (Default Settings in BOLD) Description
DMX Address 001-512 DMX Address Setting
Channel Mode 15Chan (15 channel mode) DMX Channel Setting
Show Mode
Show 1
Show 2
Show 3
Show 4
Show Modes
Split Color No (AUTO def.)
Yes (PRO def.) Split Colour Setting
Slave Mode Slave 1 (PRO & AUTO def.)
Slave 2 Slave Mode
DMX Fail
Blackout
Auto (AUTO def.)
Hold (PRO def.)
DMX Fail Setting
Sound State On (AUTO def.)
Off (PRO def.) Sound Setting
Sound Sense 000-100 (090) (PRO & AUTO def.) Sound Sensitivity Setting
Pan Inverse No (PRO & AUTO def.)
Yes Pan Inverse Setting
Tilt Inverse No (PRO & AUTO def.)
Yes Tilt Inverse Setting
Back Light On (AUTO def.)
Off (PRO def.) Back Light Setting
Focus Adjust 000-255 (016) Gobo Wheel 1 Focus Setting
Focus2 Adjust 000-255 (061) Gobo Wheel 2 Focus Setting
FunctionDelay
No Delay (PRO & AUTO def.)
1S Delay
2S Delay
3S Delay
Function Delay Setting
DimmerCalibr. 050-100 Dimmer Calibration
Auto Test Testing Auto Test
Temp. –––C Fixture Temperature
Fixture Time –––h Fixture Run Time
Firmware Ver. V–.––– Software Version
Defaults No
Yes
PRO def.
AUTO def. Default Settings
Reset No
Yes Motor Reset

www.prolight.co.uk Evora 1000 Spot User Manual 8
Operating instructions
15 channel mode:
Channel Value Function
CH1 000-255 Pan adjustment 0-540°
CH2 000-255 Pan ne adjustment
CH3 000-255 Tilt adjustment 0-270°
CH4 000-255 Tilt ne adjustment
CH5 000-255 Pan/tilt speed
CH6 000-255 Master dimmer (0-100%)
CH7
000-007 LED off
008-015 LED on
016-131 Strobe (slow-fast)
132-139 LED on
140-181 Strobe ramp up (slow-fast)
182-189 LED on
190-229 Strobe ramp down (slow-fast)
230-239 LED on
240-247 Random strobe (slow-fast)
248-255 LED on
CH8 (when
split colour
is disabled
in the menu -
see page 6)
000-015 Open (white)
016-031 Red
032-047 Orange
048-063 Green
064-079 Blue
080-095 Hot Pink
096-111 Purple
112-127 Yellow
128-189 Colour scroll CW (fast-slow)
190-193 Colour scroll stop
194-255 Colour scroll CCW (slow-fast)
Channel Value Function
CH8 (when
split colour
is enabled in
the menu -
see page 6)
000-007 Open (white)
008-016 Split colour (Open/Red)
017-025 Red
026-033 Split colour (Red/Orange)
034-042 Orange
043-050 Split colour (Orange/Green)
051-059 Green
060-067 Split colour (Green/Blue)
068-076 Blue
077-084 Split colour (Blue/Hot Pink)
085-093 Hot Pink
094-101 Split colour (Hot Pink/Purple)
102-110 Purple
111-118 Split colour (Purple/Yellow)
119-127 Yellow
128-189 Colour scroll CW (fast-slow)
190-193 Colour scroll stop
194-255 Colour scroll CCW (slow-fast)
CH9
000-007 Open
008-015 Rotating gobo 1
016-023 Rotating gobo 2
024-031 Rotating gobo 3
032-039 Rotating gobo 4
040-047 Rotating gobo 5
048-055 Rotating gobo 6
056-063 Rotating gobo 7
064-072 Gobo 1 shake (slow-fast)
073-081 Gobo 2 shake (slow-fast)
082-090 Gobo 3 shake (slow-fast)
091-099 Gobo 4 shake (slow-fast)
100-108 Gobo 5 shake (slow-fast)
109-117 Gobo 6 shake (slow-fast)
118-127 Gobo 7 shake (slow-fast)
128-189 Gobo wheel scroll CW (fast-
slow)
190-193 Gobo scroll stop
194-255 Gobo wheel scroll CCW (slow-
fast)

www.prolight.co.uk Evora 1000 Spot User Manual 9
Operating instructions
Channel Value Function
CH10
000-127 Gobo rotation index
128-189 Gobo rotation CW (fast-slow)
190-193 Rotation stop
194-255 Gobo rotation CCW (slow-fast)
CH11
000-007 Open
008-013 Static gobo 1
014-019 Static gobo 2
020-025 Static gobo 3
026-031 Static gobo 4
032-037 Static gobo 5
038-043 Static gobo 6
044-049 Static gobo 7
050-055 Static gobo 8
056-063 Static gobo 9
064-070 Gobo 1 shake (slow-fast)
071-077 Gobo 2 shake (slow-fast)
078-084 Gobo 3 shake (slow-fast)
085-091 Gobo 4 shake (slow-fast)
092-098 Gobo 5 shake (slow-fast)
099-105 Gobo 6 shake (slow-fast)
106-112 Gobo 7 shake (slow-fast)
113-119 Gobo 8 shake (slow-fast)
120-127 Gobo 9 shake (slow-fast)
128-189 Gobo wheel scroll CW
(fast-slow)
190-193 Gobo scroll stop
194-255 Gobo wheel scroll CCW
(slow-fast)
CH12
000-006 Open
007-088 3 facet prism
089-172 5 facet prism
173-255 Frost lter
CH13
000-127 Prism indexing
128-189 Prism rotation CCW (fast-slow)
190-193 Prism rotation stop
194-255 Prism rotation CW (slow-fast)
CH14 000-255 Focus
15 channel mode cont.:
Channel Value Function
CH15
000-069 Disable all
070-079 Enable blackout whilst pan/
tilt
080-089 Disable blackout whilst pan/
tilt
090-099 Enable blackout whilst colour
changing
100-109 Disable blackout whilst colour
changing
110-119 Enable blackout whilst gobo
changing
120-129 Disable blackout whilst gobo
changing
130-199 No function
200-209 Reset motors
210-249 No function
250-255 Sound active (CH6 and CH7
must be at 255)

www.prolight.co.uk Evora 1000 Spot User Manual 10
Operating instructions
Rotating gobos:
Gobo size: 20.5mmØ
Image size: 16.5mmØ
Gobo 1 Gobo 2 Gobo 3 Gobo 4
Gobo 5 Gobo 6 Gobo 7
Static gobos:
Gobo 1 Gobo 2 Gobo 3 Gobo 4 Gobo 5
Gobo 6 Gobo 7 Gobo 8 Gobo 9

www.prolight.co.uk Evora 1000 Spot User Manual 11
Setting the DMX address:
The DMX mode enables the use of a universal DMX controller. Each xture requires a “start address”
from 1- 511. A xture requiring one or more channels for control begins to read the data on the channel
indicated by the start address. For example, a xture that occupies or uses 7 channels of DMX and was
addressed to start on DMX channel 100, would read data from channels: 100,101,102,103,104,105
and 106. Choose a start address so that the channels used do not overlap. E.g. the next unit in the
chain starts at 107.
DMX 512:
DMX (Digital Multiplex) is a universal protocol used as a form of communication between intelligent
xtures and controllers. A DMX controller sends DMX data instructions form the controller to the xture.
DMX data is sent as serial data that travels from xture to xture via the DATA “IN” and DATA “OUT”
XLR terminals located on all DMX xtures (most controllers only have a data “out” terminal).
DMX linking:
DMX is a language allowing all makes and models of different manufactures to be linked together
and operate from a single controller, as long as all xtures and the controller are DMX compliant.
To ensure proper DMX data transmission, when using several DMX xtures try to use the shortest
cable path possible. The order in which xtures are connected in a DMX line does not inuence the
DMX addressing. For example; a xture assigned to a DMX address of 1 may be placed anywhere in
a DMX line, at the beginning, at the end, or anywhere in the middle. When a xture is assigned a
DMX address of 1, the DMX controller knows to send DATA assigned to address 1 to that unit,
no matter where it is located in the DMX chain.
DATA cable (DMX cable) requirements (for DMX operation):
This xture can be controlled via DMX-512 protocol. The DMX address is set on the back of the unit.
Your unit and your DMX controller require a standard 3-pin XLR connector for data input/output,
see image below.
Note: DMX cable must be daisy chained and cannot be split.
DMX setup
Further DMX cables can be
purchased from all good sound
and lighting suppliers or
Pro Light Concepts dealers.
Please quote:
CABL10 – 2m
CABL11 – 5m
CABL12 – 10m

www.prolight.co.uk Evora 1000 Spot User Manual 12
Notice:
Be sure to follow the diagrams below when making your own cables. Do not connect the cables
shield conductor to the ground lug or allow the shield conductor to come in contact with the XLRs
outer casing. Grounding the shield could cause a short circuit and erratic behaviour.
Special note:
Line termination:
When longer runs of cable are used,
you may need to use a terminator on
the last unit to avoid erratic behaviour.
Using a cable terminator will decrease
the possibilities of erratic behaviour.
(3-pin - Order ref: CABL90, 5-pin - Order ref: CABL89)
5-pin XLR DMX connectors:
Some manufactures use 5-pin XLR connectors for data transmission in place of 3-pin. 5-pin XLR xtures
may be implemented in a 3-pin XLR DMX line. When inserting standard 5-pin XLR connectors in to a
3-pin line a cable adaptor must be used. The diagram below details the correct cable conversion.
Termination reduces signal transmission
problems and interference. It is always
advisable to connect a DMX terminal,
(resistance 120 Ohm 1/4 W) between pin 2
(DMX-) and pin 3 (DMX+) of the last xture.
5-pin XLR (female)
Pin 1: GND (screen)
Pin 2: Signal (-)
Pin 3: Signal (+)
Pin 4: N/C
Pin 5: N/C
3-pin XLR (female)
Pin 1: GND (screen)
Pin 2: Signal (-)
Pin 3: Signal (+)
3-pin XLR (male)
Pin 1: GND (screen)
Pin 2: Signal (-)
Pin 3: Signal (+)
5-pin XLR (male)
Pin 1: GND (screen)
Pin 2: Signal (-)
Pin 3: Signal (+)
Pin 4: N/C
Pin 5: N/C
DMX setup

www.prolight.co.uk Evora 1000 Spot User Manual 13
WEEE notice
Correct Disposal of this Product
(Waste Electrical & Electronic Equipment)
(Applicable in the European Union and other European countries
with separate collection systems)
This marking shown on the product or its literature, indicates that it should not be disposed
with other household wastes at the end of its working life. To prevent possible harm to the
environment or human health from uncontrolled waste disposal, please separate this from other
types of wastes and recycle it responsibly to promote the sustainable reuse of material resources.
Household users should contact either the retailer where they purchased this product, or their
local government ofce, for details of where and how they can take this item for environmentally
safe recycling.
Business users should contact their supplier and check the terms and conditions of the
purchase contract. This product should not be mixed with other commercial wastes for disposal.

www.prolight.co.uk Evora 1000 Spot User Manual 14

www.prolight.co.uk Evora 1000 Spot User Manual 15

www.prolight.co.uk Evora 1000 Spot User Manual 16