ADJ Saber spot WW User manual

User Instructions
2/17
©2017 ADJ Products, LLC all rights reserved. Information,
specications, diagrams, images, and instructions herein are
subject to change without notice. ADJ Products, LLC logo and
identifying product names and numbers herein are trademarks
of ADJ Products, LLC. Copyright protection claimed includes all
forms and matters of copyrightable materials and information
now allowed by statutory or judicial law or hereinafter granted.
Product names used in this document may be trademarks or
registered trademarks of their respective companies and are
hereby acknowledged. All non-ADJ Products, LLC brands and
product names are trademarks or registered trademarks of their
respective companies.
ADJ Products, LLC and all aliated companies hereby dis-
claim any and all liabilities for property, equipment, building,
and electrical damages, injuries to any persons, and direct or
indirect economic loss associated with the use or reliance of
any information contained within this document, and/or as a
result of the improper, unsafe, unsucient and negligent as-
sembly, installation, rigging, and operation of this product.
Europe Energy Saving Notice
Energy Saving Matters (EuP 2009/125/EC)
Saving electric energy is a key to help protecting the enviroment.
Please turn o all electrical products when they are not in use. To
avoid power consumption in idle mode, disconnect all electrical
equipment from power when not in use. Thank you!
Saber Spot WW

ADJ Products, LLC - www.adj.com - Saber Spot WW Instruction Manual Page 3ADJ Products, LLC - www.adj.com - Saber Spot WW Instruction Manual Page 2
• DMX-512 Protocol Compatible (3 DMX Channel Modes: 1/2/4
• 3 Operating Modes - Show Mode, WW Dimmer Mode & DMX
Control
• 5 Dimmer Curves (Standard, Stage, TV, Architectural, & Theatre)
• Digital Display for Address and Function Setting
• UC IR Compatible (Not Included) & Airstream App Compatible
• Power Cord Daisy Chainable (See page 23)
Saber Spot WW Features
Caution! There are no user serviceable parts inside this unit. Do not
attempt any repairs yourself, doing so will void your manufactures
warranty. In the unlikely event your unit may require service please
contact ADJ Products, LLC.
During operation the housing may become extremely hot. Avoid
touching the unit with bare hands while in use.
ADJ Products, LLC will not accept any liability for any resulting dam-
ages caused by the non-observance of this manual or any unauthor-
ized modication to this unit.
Saber Spot WW Handling Precautions
Saber Spot WW Warranty Registration
The Saber Spot WW carries a 2 year (730 days) limited warranty.
Please fill out the enclosed warranty card to validate your purchase
and warranty. You may also register your product online at www. adj-
products.com. All returned service items whether under warranty or
not, must be freight pre-paid and accompany a return authorization
(R.A.) number. If the unit is under warranty you must provide a copy
of your proof of purchase invoice. Please contact ADJ Products, LLC
customer support for a R.A. number.
To optimize the performance of this product, please read these
operating instructions carefully to familiarize yourself with the basic
operations of this unit. These instructions contain important safety
information regarding the use and maintenance of this unit. Please
keep this manual with the unit, for future reference.
Saber Spot WW General Instructions
Saber Spot WW General Information
Unpacking: Thank you for purchasing the Saber Spot WW by ADJ
Products, LLC. Every Saber Spot WW has been thoroughly tested and
has been shipped in perfect operating condition. Carefully check the
shipping carton for damage that may have occurred during shipping.
If the carton appears to be damaged, carefully inspect your xture for
any damage and be sure all equipment necessary to operate the unit
has arrived intact. In the event damage has been found or parts are
missing, please contact our toll free customer support number for fur-
ther instructions. Please do not return this unit to your dealer without
contacting customer support rst.
Introduction: The Saber Spot WW is a DMX intelligent LED fix-
ture. The Saber Spot WW can operate as a stand alone fixture or in a
Master/Slave set up. The Saber Spot WW has three operating modes;
WW dimmer mode, show mode, & DMX controlled. This fixture is suit-
able for theaters, studios, retail stores, and other similar locations. For
best results use fog or special effects smoke to enhance the beams
projections.
Customer Support: ADJ Products, LLC provides a toll free cus-
tomer support line, to provide help and to answer any question should
you encounter problems during your set up or initial operation. You
may also visit us on the web at www.adj.com for any comments or
suggestions. Service Hours are Monday through Friday 8:00 a.m. to
4:30 p.m. Pacic Standard Time.
Voice: [phone]
Fax: [phone]
E-mail: [e-mail]
Warning! To prevent or reduce the risk of electrical shock or re, do
not expose this unit to rain or moisture.
Warning! This may cause severe eye damage. Avoid looking directly
into the light source at all times!

For Your Own Personal Safety, Please Read and Understand This
Manual Completely Before You Attempt To Install Or Operate
This Unit!
• To reduce the risk of electrical shock or re, do not expose this unit
rain or moisture
• Do not spill water or other liquids into or on to your unit.
• Be sure that the local power outlet match that of the required volt-
age for your unit.
• Do not attempt to operate this unit if the power cord has been
frayed or broken.
• Do not attempt to remove or break o the ground prong from
the electrical cord. This prong is used to reduce the risk of electrical
shock and re in case of an internal short.
• Disconnect from main power before making any type of connection.
• Do not remove the cover under any conditions. There are no user
serviceable parts inside.
• Never operate this unit when it’s cover is removed.
• Always be sure to mount this unit in an area that will allow proper
ventilation. Allow about 6” (15cm) between this device and a wall.
• Do not attempt to operate this unit, if it becomes damaged.
• This unit is intended for indoor use only, use of this product out-
doors voids all warranties.
• Always mount this unit in safe and stable matter.
• Power-supply cords should be routed so that they are not likely to
be walked on or pinched by items placed upon or against them,
paying particular attention to cords at plugs, convenience recep-
tacles, and the point where they exit from the appliance.
• Cleaning -The fixture should be cleaned only as recommended by
the manufacturer. See page 21 for cleaning details.
• Heat -This fixture should be situated away from heat sources such
as radiators, heat registers, stoves, or other appliances (including
amplifiers) that produce heat.
• The fixture should be serviced by qualified service personnel when:
A. Objects have fallen, or liquid has been spilled into the appliance.
B. The appliance has been exposed to rain or water.
C. The appliance does not appear to operate normally or exhibits
a marked change in performance.
Saber Spot WW Safety Precautions
ADJ Products, LLC - www.adj.com - Saber Spot WW Instruction Manual Page 5ADJ Products, LLC - www.adj.com - Saber Spot WW Instruction Manual Page 4
Power Supply: The ADJ Saber Spot WW contains a automatic volt-
age switch, which will auto sense the voltage when it is plugged into
the power source. With this switch there is no need to worry about the
correct power voltage, this unit can be plugged in anywhere.
DMX-512: DMX is short for Digital Multiplex. This is a universal pro-
tocol used by most lighting and controller manufactures as a form of
communication between intelligent fixtures and controllers. A DMX
controller sends DMX data instructions from the controller to the fix-
ture. DMX data is sent as serial data that travels from fixture to fixture
via the DATA “IN” and DATA “OUT” XLR terminals located on all DMX
fixtures (most controllers only have a DATA “OUT” terminal).
DMX Linking: DMX is a language allowing all makes and models
of dierent manufactures to be linked together and operate from a
single controller, as long as all xtures and the controller are DMX
compliant. To ensure proper DMX data transmission, when using
several DMX fixtures try to use the shortest cable path possible. The
order in which fixtures are connected in a DMX line does not influence
the DMX addressing. For example; a fixture assigned a DMX address
of 1 may be placed anywhere in a DMX line, at the beginning, at the
end, or anywhere in the middle. Therefore, the first fixture controlled
by the controller could be the last fixture in the chain. When a fixture
is assigned a DMX address of 1, the DMX controller knows to send
DATA assigned to address 1 to that unit, no matter where it is located
in the DMX chain.
Data Cable (DMX Cable) Requirements (For DMX and Master/Slave
Operation): The Saber Spot WW can be controlled via DMX-512
protocol. The Saber Spot WW has 3 DMX channel modes. The DMX
address is set electronically using the controls on
the rear panel of the unit. Your unit and your DMX
controller require a approved DMX-512 110 Ohm
Data cable for data input and data output (Figure
1). We recommend Accu-Cable DMX cables. If you
are making your own cables, be sure to use stan-
dard 110-120 Ohm shielded cable (This cable may
be purchased at almost all professional sound and
lighting stores). Your cables should be made with
Saber Spot WW DMX Set Up
Figure 1

ADJ Products, LLC - www.adj.com - Saber Spot WW Instruction Manual Page 6 ADJ Products, LLC - www.adj.com - Saber Spot WW Instruction Manual Page 7
5-Pin XLR DMX Connectors. Some manufactures use 5-pin DMX-
512 data cables for DATA transmission in place of 3-pin. 5-pin DMX
xtures may be implemented in a 3-pin DMX line. When inserting stan-
dard 5-pin data cables in to a 3-pin line a cable adaptor must be used,
these adaptors are readily available at most electric stores. The chart
below details a proper cable conversion.
Conductor 5-Pin XLR Male (In)3-Pin XLR Female (Out)
Pin 1
Pin 5 - Do Not Use
Pin 4 - Do Not Use
Pin 3
Pin 2
Pin 1
Pin 3
Pin 2
Not Used
Not Used
Data True (+ signal)
Data Compliment (- signal)
Ground/Shield
3-Pin XLR to 5-Pin XLR Conversion
Saber Spot WW DMX Set Up
a male and female XLR connector on either end of the cable. Also
remember that DMX cable must be daisy chained and cannot be split.
Saber Spot WW DMX Set Up
Notice: Be sure to follow gures two and three when making your own
cables. Do not use the ground lug on the XLR connector. Do not con-
nect the cable’s shield conductor to the ground lug or allow the shield
conductor to come in contact with the XLR’s outer casing. Grounding
the shield could cause a short circuit and erratic behavior.
DMX512 IN
3-PIN XLR
SOUND
REMOTE
CONTROL
INPUT
POWER
INPUT OUTPUT
SOUND
REMOTE
CONTROL
INPUT
POWER
INPUT OUTPUT
SOUND
REMOTE
CONTROL
INPUT
POWER
INPUT OUTPUT
DMX512
DMX+,DMX-,COMMON
1
2
3
Termination reduces signal errors and
avoids signal transmission problems
and interference. It is always advisable
to connect a DMX terminal, (Resistance
120 Ohm 1/4 W) between PIN 2 (DMX-)
and PIN 3 (DMX +) of the last fixture.
1
2
3
1
2
3
DMX +
DMX -
COMMON
DMX512 OT
3-PIN XLR
Figure 2
Figure 3
1 Ground 1 Ground
XLR Male Socket XLR Pin Conguration
3 Hot
2 Cold 2 Cold
3 Hot
XLR Female Socket
Pin 3 = Data True (positive)
Pin 2 = Data Compliment (negative)
Pin 1 = Ground
Special Note: Line Termination. When longer runs of cable are
used, you may need to use a terminator on the last unit to avoid erratic
behavior. A terminator is a 110-120 ohm 1/4 watt resistor which is con-
nected between pins 2 and 3 of a male XLR connector (DATA + and
DATA -). This unit is inserted in the female XLR connector of the last
unit in your daisy chain to terminate the line. Using a cable terminator
(ADJ part number Z-DMX/T) will decrease the possibilities of erratic
behavior.
DMX512 IN
3-PIN XLR
SOUND
REMOTE
CONTROL
INPUT
POWER
INPUT OUTPUT
SOUND
REMOTE
CONTROL
INPUT
POWER
INPUT OUTPUT
SOUND
REMOTE
CONTROL
INPUT
POWER
INPUT OUTPUT
DMX512
DMX+,DMX-,COMMON
1
2
3
Termination reduces signal errors and
avoids signal transmission problems
and interference. It is always advisable
to connect a DMX terminal, (Resistance
120 Ohm 1/4 W) between PIN 2 (DMX-)
and PIN 3 (DMX +) of the last fixture.
1
2
3
1
2
3
DMX +
DMX -
COMMON
DMX512 OT
3-PIN XLR
Figure 4

ADJ Products, LLC - www.adj.com - Saber Spot WW Instruction Manual Page 9ADJ Products, LLC - www.adj.com - Saber Spot WW Instruction Manual Page 8
Saber Spot WW System Menu
System Menu: When making adjustments press ENTER to
conrm your setup then press and hold the MENU button
for at least 3 seconds. To exit without making any adjust-
ments press the MENU button. The display will lock after 30
seconds, press the MENU button for 3 seconds to unlock.
DMX MODE - DMX Address Setting.
1. Press the either the MENU, UP, or DOWN buttons until “DMX
MODE” is displayed, press ENTER.
2. The current address will now be displayed and ashing.
Press the UP or DOWN buttons to nd your desired address.
Press ENTER to set your desired DMX address.
CHANNEL - This will let select your desired DMX
channel mode.
1. Press the either the MENU button until “CHANNEL” is dis-
played, press ENTER. The current DMX channel mode will be
displayed.
2. Press the UP or DOWN buttons to nd your desired DMX
channel mode and press ENTER to conm and exit.
SLAVE - This will let you set the unit as the slave in a
master/slave conguration.
1. Press the MENU button until “SLAVE” is displayed, press
ENTER.
LOOK - In this mode you can run a show mode.
1. Press the MENU button until “LOOK” is displayed, press
ENTER.
2. Use the UP or DOWN buttons to nd your desired mode.
Saber Spot WW System Menu
Software Update
Please Wait ...
ADJ
SOFTWAREV1.0 3
About LED protection ：
When reach 65 degree, the power consumption is reduced to 82%. When the sensor is
damaged, the power consumption is reduced to 65%.
SN MENU DISPLAY FUNCTION
1 DMX MODE
ADDR：001
Address setting
001- 512
2 CHANNNEL 4CH 1/2/4CH(see channel mode)
3 Slave Slave mode
4 LOOK
Store:01 Store mode 01- 13
5 Reset ？
NO
Yes,press ENTER to resume the factory
default setting
6 Manual
W 000- 255 S 000- 255
Manual dimmer
W 000- 255 strobe ：S000- 255
7 DimCurve
Standard
5 kinds Dimmer curve
Standard, Stage, TV, Architec,
Theatre
8 NO DMX No DMX mode
Hold Blackout, Hold, LOOK
9 TempUnit C/F
10 Temp Val Temperature show: xxx F
11 AUTOLOCK Display keylock OFF/ON
12 IR Active IR setting OFF/ON
13 FlipDisplay Flip display OFF/ON
Display Menu
Special Remark:

ADJ Products, LLC - www.adj.com - Saber Spot WW Instruction Manual Page 10 ADJ Products, LLC - www.adj.com - Saber Spot WW Instruction Manual Page 11
2. Press the UP or DOWN buttons to nd your desired dimmer
curve and press ENTER to conm.
NO DMX - This mode can be used as a precaution mode,
that in case the DMX signal is lost, interrupted, or power is
lost, the operating mode chosen in the setup is the running
mode the xture will go into when the DMX signal is lost. You
can also set this as the operating mode you would like the
unit to return to when power is applied.
1. Press the MENU button until “NO DMX” is displayed, and
either “Look”, “Blackout”, or “Hold” will be displayed beneath.
2. Press ENTER and the bottom choice will begin to ash. Use
the UP or DOWN buttons to choose an operating mode you
would like the unit to start up in when power is applied or the
DMX signal is lost.
• Look (Master Slave) - If the DMX signal is lost or power is
applied, the unit will automatically run a built-in show.
• Blackout - If the DMX signal is lost or interrupted, the unit will
automatically go into stand by mode.
• Hold - If the DMX signal is lost the xture will stay in the last
DMX setting. If power is applied and this mode is set, the unit will
automatically go into the last DMX set up.
3. Press ENTER to conrm your desired set up.
TempUnit - With this function you can switch the tem-
perature display to show either Celsius or Fahrenheit.
1. Press the MENU button until “TempUnit” is displayed, press
ENTER.
2. Use the UP or DOWN buttons to switch between Celsius or
Fahrenheit. Press ENTER to select your desired setting.
Saber Spot WW System Menu
RESET - This function will return the unit to its default
settings.
1. Press the the MENU button until “RESET” is displayed and
press ENTER.
2. The display will show either “NO” or “YES”. Press the UP or
DOWN buttons so that “YES” is displayed. Press ENTER and
the unit will reset back to default settings.
MANUAL - This function will allow you to manually
adjust each LED output intensity and strobe rate. This func-
tion is also a manual testing mode.
1. Press the MENU button until “MANUAL” is displayed, press
ENTER.
2. Using the UP or DOWN buttons scroll to the Strobe setting
and press ENTER. Use the UP or DOWN buttons to set the
strobe setting to “255”, and press ENTER again
3. After you have set the strobe setting to “255”, press the
UP or DOWN buttons so that W:XXX is displayed and press
ENTER. Now use the UP or DOWN buttons to adjust the output
intensity.
4. If you would like the unit to strobe, scroll back to the strobe
setting and press ENTER. Use the UP or DOWN buttons to
adjust the strobe rate. Press ENTER once you have found your
desired strobe rate.
DimCurve - This will let select your desired dimmer
curve.
1. Press the MENU button until “DimCurve” is displayed, and
press ENTER. 1 of 5 dimmer curves will be displayed. “STAN-
DARD”, “STAGE”, “TV”, “ARCHITEC” (Architectural), or “THE-
ATRE”. See the dimmer curve chart on page 199 for more info.
Saber Spot WW System Menu

ADJ Products, LLC - www.adj.com - Saber Spot WW Instruction Manual Page 12 ADJ Products, LLC - www.adj.com - Saber Spot WW Instruction Manual Page 13
Temp Val - With this function you can check the tem-
perature of the xture.
1. Press the MENU button until “Temp Val” is displayed, press
ENTER.
2. The xture temperature will now be displayed. Press MENU
to exit.
AUTOLOCK - With this function you can have the
keys lock off after 10 seconds of no use.
1. Press the MENU button until “AUTOLOCK” is displayed,
press ENTER.
2. The display will show either “ON” or “OFF”. Press the UP or
DOWN buttons to select “ON” to have the keys lock after 10
seconds, or “OFF” so that the keys will remain unlocked.
3. Press ENTER to conrm.
IR Active - With this function you can activate the IR
function and use the UC IR or Airstream app to control the
unit.
1. Press the MENU button until “IR Active” is displayed, press
ENTER.
2. The display will show either “ON” or “OFF”. Press the UP or
DOWN buttons to select “ON” to activate IR function, or “OFF”
to turn o the IR function.
3. Press ENTER to conrm. See page 16 for IR controls.
FlipDisplay - This function will reverse the display
180º.
1. Press the either the MENU button until “FlipDisplay” is dis-
Saber Spot WW System Menu
played, press ENTER.
2. The display will show either “ON” or “OFF”. Press the UP or
DOWN buttons to select “ON” to ip the display, or “OFF” to
keep the display normal.
3. Press ENTER to conrm.
Saber Spot WW System Menu

ADJ Products, LLC - www.adj.com - Saber Spot WW Instruction Manual Page 15ADJ Products, LLC - www.adj.com - Saber Spot WW Instruction Manual Page 14
Universal DMX Control: This function allows you to use a uni-
versal DMX-512 controller to control the colors, master dimmer and
strobe. A DMX controller allows you to create unique programs tai-
lored to your individual needs.
1. The Saber Spot WW has 3 DMX channel modes. See pages
17-18 for detailed description of the DMX values and traits.
2. To control your fixture in DMX mode, follow the set-up procedures
on pages 7-9 as well as the set-up specifications that are includ-
ed with your DMX controller.
3. Use the controller’s faders to control the various DMX fixture traits.
4. This will allow you to create your own programs.
5. Follow the instruction on page 9 to select your DMX channel
mode and set your desired DMX address.
6. For longer cable runs (more than a 100 feet) use a terminator on
the last fixture.
7. For help operating in DMX mode consult the manual included
with your DMX controller.
Show Mode: This mode allows either a single unit or several units
linked together to run a built-in program.
1. Press the MENU button until “Look” is displayed, and press
ENTER.
2. Press the UP or DOWN buttons to nd your desired show.
Saber Spot WW Operation Saber Spot WW Master-Slave Set Up
Master-Slave Operation This function will allow you to link up to
16 units together and operate without a controller. In a Master-Slave
set up, one unit will act as the controlling unit and the others will react
to the controlling units programs. Any unit can act as a Master or as a
Slave.
1. Using approved DMX data cables, daisy chain your units togeth-
er via the XLR connector on the rear of the units. Remember the
Male XLR connector is the input and the Female XLR connector
is the output. The rst unit in the chain (master) will use the female
XLR connector only - The last unit in the chain will use the male
XLR connector only. For longer cable runs we suggest a termina-
tor at the last fixture.
2. On the Master unit nd your desired operating mode.
3. On the slave units press the MENU button until “Slave” is dis-
played.
4. The slave units will now follow the Master unit.
Saber Spot WW Installing the Frost Lens
The Saber Spot WW Plus comes with 2 frost filters. Install the filter in
front of the lens and put the inlcuded retainer ring top to hold the lens
in place.

ADJ Products, LLC - www.adj.com - Saber Spot WW Instruction Manual Page 16 ADJ Products, LLC - www.adj.com - Saber Spot WW Instruction Manual Page 17
The UC IR (sold separately) infrared remote gives you control of
various functions (See below). To control the fixture you must aim the
remote at the front of the fixture and be no more than 30 feet away.
The Saber Spot WW is also compatible with the Airstream IR app.
The IR transmitter is available through any ADJ dealer or through the
ADJ parts website. Plug the transmitter into the headphone jack of
your iOS phone or tablet. To control your IR fixture you must raise
the volume to the maximum on your iOS phone or tablet and aim
the transmitter at the front of the fixture and be no more than 15
feet away. After you have purchased the Airstream IR transmitters,
the app is a free download from the app store for your iOS phone or
tablet. The app comes with 3 pages of control depending on the IR
fixture you are using. Please see below for IR functions including the
corresponding app page.
Works with App page 1.
STAND BY - Press this button to go into DMX mode or IR active.
FULL ON -Press this button down to fully light up the unit.
STROBE - Press this button to activate strobing. Use the “Dimmer
+/- to adjust the strobe rate.
FADE/GOBO - Press this button to activate fade mode. Continue to
press this button to find your desired fade speed.
“DIMMER +” and “DIMMER -” - Use these buttons adjust the strobe
rate and output intensity in color mode.
COLOR - This button is will activate the warm white color. You must
first press Full On then press Color twice until it blacksout. Then you
can use the Dimmer +/- to adjust the output intensity.
1-9 - These buttons are invalid for this fixture.
SOUND ON & OFF - These buttons are invalid for this fixture.
SHOW 0 - This button is invalid for this fixture.
Saber Spot WW UC IR Operation
Channel Value Function
1 WARM WHITE
0 - 255 0% - 100%
Saber Spot WW 1 Channel Mode
Channel Value Function
1 WARM WHITE
0 - 255 0% - 100%
2 SHUTTER/STROBE
0 - 31 LED OFF
32 - 63 LED ON
64 - 95 STROBING SLOW - FAST
96 - 127 LED ON
128 - 159 PULSE STROBE SLOW - FAST
160 - 191 LED ON
192 - 223 RANDOM STROBE SLOW - FAST
224 - 255 LED ON
Saber Spot WW 2 Channel Mode

ADJ Products, LLC - www.adj.com - Saber Spot WW Instruction Manual Page 18 ADJ Products, LLC - www.adj.com - Saber Spot WW Instruction Manual Page 19
Channel Value Function
1 WARM WHITE
0 - 255 0% - 100%
2 WARM WHITE FINE
0 - 255 0% - 100%
3 SHUTTER/STROBE
0 - 31 LED OFF
32 - 63 LED ON
64 - 95 STROBING SLOW - FAST
96 - 127 LED ON
128 - 159 PULSE STROBE SLOW - FAST
160 - 191 LED ON
192 - 223 RANDOM STROBE SLOW - FAST
224 - 255 LED ON
4 DIMMER CURVES
0 - 20 STANDARD
21 - 40 STAGE
41 - 60 TV
61 - 80 ARCHITECTURAL
81 - 100 THEATRE
101 - 255 DEFAULT DIMMER SETTING
Saber Spot WW 4 Channel Mode Saber Spot WW Dimmer Curve Chart
(Fade Time) (Fade Time)
Ramp Effect
Standard
Stage
TV
Architectural
Theatre
Saber Spot WW CAD Drawing
108mm [4.3in]
135mm [5.3in]
76mm [3.0in]
28mm [1.1in]
160mm [6.3in]
170mm [6.7in]
215mm [8.5in]
230mm [ 9.1in ]

ADJ Products, LLC - www.adj.com - Saber Spot WW Instruction Manual Page 20 ADJ Products, LLC - www.adj.com - Saber Spot WW Instruction Manual Page 21
Saber Spot WW Photometric Chart
Intensity(LUX)
Beam angle
Field angle 8°
4°
Full LEDs 51890 13030 5536 3093 1956
8°
4°
0
0 1 2 3 4 5
1
1
2
2
3
4
Beam opening(m)
3
4
0.15
0.06 0.24 0.33 0.414°
Diameter (m)
0.31
0.13 0.48 0.66 0.838°
Diameter (m)
Saber Spot WW Photometric Chart
Intensity(LUX)
Beam angle 10°
10°
0
0 1 2 3 4 5
1
1
2
2
3
4
Beam opening(m)
3
4
0.35
0.17 0.52 0.70 0.87
Diameter (m)10°
Full LEDs 20880 5399 2303 1339 842
(single face)frost filter

ADJ Products, LLC - www.adj.com - Saber Spot WW Instruction Manual Page 22
Saber Spot WW Cleaning
Saber Spot WW Trouble Shooting
Trouble Shooting: Listed below are a few common problems that
you may encounter, with solutions.
No light output in WW Dimmer Mode;
1. Be sure the strobe setting is set to value 255.
Due to fog residue, smoke, and dust cleaning the internal and exter-
nal optical lenses and mirror should be carried out periodically to
optimize light output. Cleaning frequency depends on the environ-
ment in which the fixture operates (I.e. smoke, fog residue, dust,
dew). In heavy club use we recommend cleaning on a monthly basis.
Periodic cleaning will ensure longevity, and crisp output.
1. Use normal glass cleaner and a soft cloth to wipe down the out-
side casing.
2. Use a brush to wipe down the cooling vents and fan grill.
3. Clean the external optics with glass cleaner and a soft cloth every
20 days.
4. Clean the internal optics with glass cleaner and a soft cloth every
30-60 days.
5. Always be sure to dry all parts completely before plugging the unit
back in.
With this feature you can connect the xtures to one another
using the PowerCON input and output sockets. The quantity that
can be connected is 36 xtures maximum @ 110V and a maxi-
mum 65 xture’s @ 240V. After maximum limit has been reached
you will need to use a new power outlet. They must be the same
xtures. DO NOT mix xtures.
Saber Spot WW Power Cord Daisy Chain
Saber Spot WW Photometric Chart
Intensity(LUX)
Beam angle 45°
0
0 1 2 3 4 5
1
1
2
2
3
4
Beam opening(m)
3
4
45
1.66
0.83 2.49 3.31 4.1445°
Diameter (m)
Full LEDs 2870 749 330 194 126
(double face)frost filter
ADJ Products, LLC - www.adj.com - Saber Spot WW Instruction Manual Page 23

ADJ Products, LLC - www.adj.com - Saber Spot WW Instruction Manual Page 24 ADJ Products, LLC - www.adj.com - Saber Spot WW Instruction Manual Page 25
Saber Spot WW NotesSaber Spot WW Warranty
MANUFACTURER’S LIMITED WARRANTY
A. ADJ Products, LLC hereby warrants, to the original purchaser, ADJ Products, LLC products
to be free of manufacturing defects in material and workmanship for a prescribed period from
the date of purchase (see specific warranty period on reverse). This warranty shall be valid only if the
product is purchased within the United States of America, including possessions and
territories. It is the owner’s responsibility to establish the date and place of purchase by acceptable
evidence, at the time service is sought.
B. For warranty service you must obtain a Return Authorization number (RA#)
before sending back the product–please contact ADJ Products, LLC Service Department
at 800-322-6337. Send the product only to the ADJ Products, LLC factory. All
shipping charges must be pre-paid. If the requested repairs or service (including
parts replacement) are within the terms of this warranty, ADJ Products, LLC will pay return
shipping charges only to a designated point within the United States. If the entire instrument is
sent, it must be shipped in it’s original package. No accessories should be shipped with the product. If
any accessories are shipped with the product, ADJ Products, LLC shall have no liability whatsoever for
loss of or damage to any such accessories, nor for the safe return thereof.
C. This warranty is void if the serial number has been altered or removed; if the product is modified in any
manner which ADJ Products, LLC concludes, after inspection, affects the reliability of the product; if the
product has been repaired or serviced by anyone other than the ADJ Products, LLC factory unless prior
written authorization was issued to purchaser by ADJ Products, LLC; if the product is damaged because
not properly maintained as set forth in the instruction manual.
D. This is not a service contract, and this warranty does not include maintnance, cleaning or periodic check
up. During the period specified above, ADJ Products, LLC will replace defective parts at its expense
with new or refurbished parts, and will absorb all expenses for warranty service and repair labor by
reason of defects in material or workmanship. The sole responsibility of ADJ Products, LLC under this
warranty shall be limited to the repair of the product, or replacement thereof, including parts, at the sole
discretion of ADJ Products, LLC. All products covered by this warranty were manufactured after August
15, 2012, and bear indentifying marks to that effect.
E. ADJ Products, LLC reserves the right to make changes in design and/or improvements upon its products
without any obligation to include these changes in any products theretofore manufactured.
No warranty, whether expressed or implied, is given or made with respect to any accessory supplied with
products described above. Except to the extent prohibited by applicable law, all implied warranties made
by ADJ Products, LLC in connection with this product, including warranties of merchantability or fitness,
are limited in duration to the warranty period set forth above. And no warranties, whether expressed or
implied, including warranties of merchantability or fitness, shall apply to this product after said period
has expired. The consumer’s and/or Dealer’s sole remedy shall be such repair or replacement as is
expressly provided above; and under no circumstances shall ADJ Products, LLC be liable for any loss or
damage, direct or consequential, arising out of the use of, or inability to use, this product.
This warranty is the only written warranty applicable to ADJ Products, LLC Products and
supersedes all prior warranties and written descriptions of warranty terms and conditions heretofore
published.
MANUFACTURER’S LIMITED WARRANTY PERIODS:
 •NonL.E.D.LightingProducts=1-year(365days)LimitedWarranty(Such as: Special Effect
Lighting, Intelligent Lighting, UV lighting, Strobes, Fog Machines, Bubble Machines, Mirror Balls, Par
Cans, Trussing, Lighting Stands etc. excluding LED and lamps)
 •LaserProducts=1Year(365Days)LimitedWarranty(excluding laser diodes which have a 6 month
limited warranty)
 •L.E.D.Products=2-year(730days)LimitedWarranty(excluding batteries which have a 180 day lim-
ited warranty). Note:2YearWarrantyonlyappliestopurchaseswithintheUnitedStates.
 •StarTecSeries=1YearLimitedWarranty(excluding batteries which have a 180 day limited war-
ranty).
•ADJDMXControllers=2Year(730Days)LimitedWarranty

Please Note: Specications and improvements in the design
of this unit and this manual are subject to change without any
prior written notice.
Saber Spot WW Specifications
Auto Sensing Voltage: This xture contains a automatic volt-
age switch, which will auto sense the voltage when it is plugged
into the power source.
ADJ Products, LLC
6122 S. Eastern Ave. Los Angeles, CA 90040 USA
Tel: [phone] / Fax: [phone]
Web: www.adj.com / E-mail: [email protected]
A.D.J. Supply Europe B.V.
Junostraat 2
6468 EW Kerkrade
The Netherlands
[email protected] / www.adj.eu
Tel: [phone] / Fax: [phone]
Model: Saber Spot WW
Voltage: 100~240V, 50/60Hz
LEDs: 1 x 15W WW LED
LED Life: 10,000 Hrs.
Beam Angle: 4 Degrees
10 Degrees (Frost Filter 1)
45 Degrees (Frost Filter 2)
Power Consumption: 15W
PowerCon Daisy Chain: 36 Fixtures Max. (110V
65 Fixtures Max. (240V)
Dimensions: 6.7”(L) x 5.3”(W) x 8.5”(H)
170 x 135 x 215mm
Weight: 2.6 Lbs. / 1.2 kgs.
Colors: WW
Duty Cycle: None
DMX: 3 DMX Channel Modes: 1/2/4
Sound Active: No
Working Position: Any Safe, Secure Position
Warranty: 2 Year (730 days)
ADJ Products, LLC - www.adj.com - Saber Spot WW Instruction Manual Page 26