Ledj 150W COB RGBA Par User manual

Order code: LEDJ375
150W COB CW/WW Par
User Manual

www.prolight.co.uk 150W COB CW/WW Par User Manual 2
Safety advice
WARNING
FOR YOUR OWN SAFETY, PLEASE READ THIS USER MANUAL
CAREFULLY BEFORE YOUR INITIAL START-UP!
• Beforeyourinitialstart-up,pleasemakesurethatthereisnodamagecausedduringtransportation.
• Shouldtherebeanydamage,consultyourdealeranddonotusetheequipment.
• Tomaintaintheequipmentingoodworkingconditionandtoensuresafeoperation,itisnecessary
fortheusertofollowthesafetyinstructionsandwarningnoteswritteninthismanual.
• Pleasenotethatdamagescausedbyusermodicationstothisequipmentarenotsubjecttowarranty.
IMPORTANT:
The manufacturer will not accept liability for any resulting damages caused by the non-observance
of this manual or any unauthorised modication to the equipment.
OPERATING DETERMINATIONS
Ifthisequipmentisoperatedinanyotherway,thanthosedescribedinthismanual,theproductmaysufferdamageand
thewarrantybecomesvoid.Incorrectoperationmayleadtodangere.g:short-circuit,burnsandelectricshocksetc.
Donotendangeryourownsafetyandthesafetyofothers!
Incorrectinstallationorusecancauseseriousdamagetopeopleand/orproperty.
CAUTION!
KEEP THIS EQUIPMENT
AWAY FROM RAIN,
MOISTURE AND LIQUIDS
CAUTION!
TAKE CARE USING
THIS EQUIPMENT!
HIGH VOLTAGE-RISK
OF ELECTRIC SHOCK!!
• Neverletthepowercablecomeintocontactwithother
cables.Handlethepowercableandallmainsvoltage
connectionswithparticularcaution!
• Neverremovewarningorinformativelabelsfromtheunit.
• Donotopentheequipmentanddonotmodifytheunit.
• Donotconnectthisequipmenttoadimmerpack.
• Donotswitchtheequipmentonandoffinshortintervals,
asthiswillreducethesystem’slife.
• Onlyusetheequipmentindoors.
• Donotexposetoammablesources,liquidsorgases.
• Alwaysdisconnectthepowerfromthemainswhen
equipmentisnotinuseorbeforecleaning!Onlyhandle
thepower-cablebytheplug.Neverpullouttheplugby
pullingthepower-cable.
• Makesurethattheavailablemainssupplyvoltageis
between100~240VAC,50/60Hz.
• Makesurethatthepowercableisnevercrimpedor
damaged.Checktheequipmentandthepowercable
periodically.
• Iftheequipmentisdroppedordamaged,disconnectthe
mainspowersupplyimmediatelyandhaveaqualied
engineerinspecttheequipmentbeforeoperatingagain.

• Iftheequipmenthasbeenexposedtodrastic
temperatureuctuation(e.g.aftertransportation),
donotconnectpowerorswitchitonimmediately.
Thearisingcondensationmightdamagetheequipment.
Leavetheequipmentswitchedoffuntilithasreached
roomtemperature.
• Ifyourproductfailstofunctioncorrectly,stopuse
immediately.Packtheunitsecurely(preferablyinthe
originalpackingmaterial),andreturnittoyourProLight
dealerforservice.
• Onlyusefusesofsametypeandrating.
• Repairs,servicingandpowerconnectionmustonlybe
carriedoutbyaqualiedtechnician.THISUNITCONTAINS
NOUSERSERVICEABLEPARTS.
• Thislightingxtureisforprofessionaluseonly-itis
notdesignedfororsuitableforhouseholduse.The
productmustbeinstalledbyaqualiedtechnicianin
accordancewithlocalterritoryregulations.Thesafetyof
theinstallationistheresponsibilityoftheinstaller.The
xturepresentsrisksofsevereinjuryordeathduetore
hazards,electricshockandfalls.
• Warning!RiskGroup2LEDproductaccordingto
EN62471.Donotviewthelightoutputwithoptical
instrumentsoranydevicethatmayconcentratethebeam.
• WARRANTY:Oneyearfromdateofpurchase.

www.prolight.co.uk 150W COB CW/WW Par User Manual 3
0m 2m 3m 4m 5m1m
3180
1888
1310
12700
7560
5240
1410
840
582
795
472
328
509
302
210
4717
2812
1943
18900
11200
7760
2100
1250
862
1180
703
485
755
450
310
80° - Lux
FULL ON
CW
WW
50° - Lux
FULL ON
CW
WW
40° - Lux
FULL ON
CW
WW
5864
3497
2436
23400
14000
9760
2600
1560
1080
1470
875
610
938
560
390
25° - Lux
FULL ON
CW
WW
7312
4420
3078
29200
17700
12300
3250
1960
1370
1830
1110
770
1170
707
493
50 8040°25° ° °
Product overview & technical specications
TheLEDJ150WCOBCW/WWParusesaCOBLEDtoproduceahighoutputwashwithsmoothcolourmixingand
nocolourshadows.Theyfeaturean80°beamangleandalsocomesuppliedwiththreebeamreductionlenses
(25°,40°and50°)whichareeasilyinterchangeable.The4-buttonDMXdisplayallowsaccessofbuilt-incolour
macros,4selectabledimmercurves,0-100%electronicdimmingandselectionsofstand-aloneandDMXmodes.
150W COB CW/WW Par
257mm 320mm
353mm
•1x150Wcoolwhiteandwarmwhite
COBLED(CW/WW)
•Beamangle:80°native,25°,40°
and50°beamreductionlenses
supplied
•80°-3,180Lux@2m(fullon)
•5kHzrefreshrate
•DMXchannels:2/3/4or6selectable
•Autoandmaster/slavemodes
plusbuilt-inprograms
•0-100%dimmingand
variablestrobe
•Suppliedwithhangingbracket
•4pushbuttonmenuwithLEDdisplay
•PowerCONinput/output
•5-PinXLRinput/output
•3-PinXLRinput/output
•Fancooled
Specications 150W COB CW/WW Par
Powerconsumption 155W
Powersupply 100~240V,50/60Hz
Fuse T3A250V
Dimensions 353x257x320mm
Weight 4.4kg
Ordercode LEDJ375

www.prolight.co.uk 150W COB CW/WW Par User Manual 4
Technical specications
01-Earthpoint
02-Safetyeye
03-LEDdisplay
04-Functionbuttons
05-3-PinDMXinput
06-3-PinDMXoutput
07-5-PinDMXinput
08-5-PinDMXoutput
09-PowerCONinput
10-PowerCONoutput
11-FuseT3A250V
12-Hangingbracket
13-Hangingbracketadjustableknob
Inthebox:1 x xture,
1 x 25° beam reduction lens,
1 x 40° beam reduction lens,
1 x 50° beam reduction lens,
1 x power cable
& 1 x user manual
5-PIN DMX INPUT 5-PIN DMX OUTPUT
3-PIN DMX INPUT 3-PIN DMX OUTPUT
FUSE:
T3A 250V
POWER INPUT:
100-240V~50/60Hz
POWER OUTPUT:
100-240V~50/60Hz
MENU UPENTER DOWN
150W COB CW/WW Par
www.prolight.co.uk
12
09
13
05
11 07 0801 02
04
03
13
12
10
06

www.prolight.co.uk 150W COB CW/WW Par User Manual 5
Operating instructions
MENU
S L A u
Slave mode
d o n
don
d o F F
Display backlight
S t n d
rEv
Display inverse
d E F A
Reset factory settings
h. 0 0 0
h. 2 5 5
C. 0 0 0
C. 2 5 5
F5.00
F5.15
Manual dimming
mode
h. 2 5 5
C L 0 0
C L 0 8
F 5. 0 0
F 5. 1 5
Static colour mode
C L 0 0
Ch02
d. 0 0 1
d. 5 1 2
C h 0 3
C h 0 4
dr-1
dr-4
DMX settings/
dimmer curves
d. 0 0 1
Ch06

www.prolight.co.uk 150W COB CW/WW Par User Manual 6
DMX mode:
OperatinginaDMXcontrolmodeenvironmentgivestheuserthegreatestexibilitywhenitcomes
tocustomisingorcreatingashow.Inthismodeyouwillbeabletocontroleachindividualtraitof
thextureandeachxtureindependently.
ToaccesstheDMXaddressmode,pressthe“MENU”buttonontherearoftheunittoshowd.001on
theLEDdisplay.Nowusethe“UP”and“DOWN”buttonstosettherequiredDMXaddress.Pressthe
“ENTER”buttontoconrmthesetting. TheDMXchannelmodewillnowbedisplayed,usethe“UP”and
“DOWN”buttonsontherearoftheunittoselecteither2/3/4or6DMXchannelmode.
Pressthe“ENTER”buttontoconrmthesetting.Thedimmingcurvesettingswillnowbedisplayed,use
the“UP”and“DOWN”buttonsontherearoftheunittoselectbetweendr-1~dr-4.
Pressthe“ENTER” buttontoconrmthesetting.
Toexitoutofanyoftheaboveoptions,pressthe“MENU”button.
Operating instructions
Channel Value Function
1 000-255 CoolWhitedimmer(0-100%)
2000-255 WarmWhitedimmer(0-100%)
2 channel mode:
Channel Value Function
1 000-255 CoolWhitedimmer(0-100%)
2000-255 WarmWhitedimmer(0-100%)
3000-020 Linear(dimmingcurve)
021-040 SquareLaw(dimmingcurve)
041-060 InverseSquareLaw(dimmingcurve)
061-080 S-Curve(dimmingcurve)
081-255 Defaultdimmingcurve(setviamenu)
3 channel mode:
Channel Value Function
1 000-255 CoolWhitedimmer(0-100%)
2000-255 WarmWhitedimmer(0-100%)
3000-255 Masterdimmer(0-100%)
4 000-020 Linear(dimmingcurve)
021-040 SquareLaw(dimmingcurve)
041-060 InverseSquareLaw(dimmingcurve)
061-080 S-Curve(dimmingcurve)
081-255 Defaultdimmingcurve(setviamenu)
4 channel mode:
Channel Value Function
1 000-255 CoolWhitedimmer(0-100%)
2000-255 WarmWhitedimmer(0-100%)
3000 Nofunction
001-255 Variablewhite(3200K-6400K)
4 000-015 Nofunction
016-255 Strobe(slow-fast)
5 000-255 Masterdimmer(0-100%)
6 000-020 Linear(dimmingcurve)
021-040 SquareLaw(dimmingcurve)
041-060 InverseSquareLaw(dimmingcurve)
061-080 S-Curve(dimmingcurve)
081-255 Defaultdimmingcurve(setviamenu)
6 channel mode:
dr-3-InverseSquareLaw dr-4-S-curvedr-1-Linear dr-2-SquareLaw

www.prolight.co.uk 150W COB CW/WW Par User Manual 7
Operating instructions
Master/slave mode:
Tosetthemasterunit,pressthe“MENU”buttonontherearofthemasterunitthenselectyour
desiredprogram(soundactiveordimmermodes).Tosettheotherunitsinslavemode,pressthe
“MENU”buttonontherearoftheunittoshowSLAuontheLEDdisplayandpressthe“ENTER”
buttontoconrmthesetting.Theunitswillnowruninsequencewiththemasterunit.
Toexitoutofanyoftheaboveoptions,pressthe“MENU”button.
PleaseensurethatallslaveunitsaresettothesameDMXchannelmodeasthemasterunit.
Manual dimming mode:
Toaccessthemanualdimmingmode,pressthe“MENU”buttonuntilthedisplayshowsh.255onthe
LEDdisplay.Usethe“UP”and“DOWN”buttonstoselecttherequiredbrightnessofwarmwhitefrom
h.000~h.255.Pressthe“ENTER” buttonandthenusethe“UP”and“DOWN”buttonstoselectthe
requiredbrightnessofcoolwhitefromC.000~C.255.Toadjusttheashspeedpressthe“ENTER”
buttonandthenusethe“UP”and“DOWN”buttonstoselectanyvaluefromF5.00~F5.15.
Pressthe“ENTER” buttontoconrmthesetting.
Value: 000 - 255 (000 = low brightness, 255 = high brightness)
Value: 00 - 15 (00 = no ash, 15 = fast ash speed)
Toexitoutofanyoftheaboveoptions,pressthe“MENU”button.
Static colour:
Toaccessthestaticcolourmode,pressthe“MENU”buttonuntilthedisplayshowsCL00ontheLED
display.Usethe“UP”and“DOWN”buttonstoselecttherequiredstaticcolourfromCL00~CL08.
Toadjusttheashspeedpressthe“ENTER” buttonandthenusethe“UP”and“DOWN”buttonsto
selectanyvaluefromF5.00~F5.15.Pressthe“ENTER” buttontoconrmthesetting.
Value: 00 - 15 (00 = no ash, 15 = fast ash speed)
Toexitoutofanyoftheaboveoptions,pressthe“MENU”button.
Display backlight:
Toaccessthedisplaybacklightsetting,pressthe“MENU”buttonuntilthedisplayshowsdononthe
LEDdisplay.Usethe“UP”and“DOWN”buttonstoselecteitherdon(displaybacklighton)~doff
(displaybacklightoff).Pressthe“ENTER” buttontoconrmthesetting.
Toexitoutofanyoftheaboveoptions,pressthe“MENU”button.
Display inverse:
Toaccessthedisplayinversesetting,pressthe“MENU”buttonuntilthedisplayshowsdononthe
LEDdisplay.Pressthe“ENTER” buttontodisplayStndandusethe“UP”and“DOWN”buttonsto
selecteitherStnd(displaystandard)~ (displayinverse).
Pressthe“ENTER” buttontoconrmthesetting.
Toexitoutofanyoftheaboveoptions,pressthe“MENU”button.
rEv

www.prolight.co.uk 150W COB CW/WW Par User Manual 8
Operating instructions
Reset factory settings:
Toresetthefactorysettings,pressthe“MENU”buttonuntilthedisplayshowsdonontheLEDdisplay.
Pressthe“ENTER” buttontwicetodisplaydEFa.Pressthe“UP”and“DOWN”buttonstogether
andthexturewillberesettoitsfactorysettings.
Toexitoutofanyoftheaboveoptions,pressthe“MENU”button.

www.prolight.co.uk 150W COB CW/WW Par User Manual 9
Setting the DMX address:
TheDMXmodeenablestheuseofauniversalDMXcontroller.Eachxturerequiresa“startaddress”
from1-511.Axturerequiringoneormorechannelsforcontrolbeginstoreadthedataonthechannel
indicatedbythestartaddress.Forexample,axturethatoccupiesoruses7channelsofDMXandwas
addressedtostartonDMXchannel100,wouldreaddatafromchannels:100,101,102,103,104,105
and106.Chooseastartaddresssothatthechannelsuseddonotoverlap.E.g.thenextunitinthe
chainstartsat107.
DMX 512:
DMX(DigitalMultiplex)isauniversalprotocolusedasaformofcommunicationbetweenintelligent
xturesandcontrollers.ADMXcontrollersendsDMXdatainstructionsformthecontrollertothexture.
DMXdataissentasserialdatathattravelsfromxturetoxtureviatheDATA“IN”andDATA“OUT”
XLRterminalslocatedonallDMXxtures(mostcontrollersonlyhaveadata“out”terminal).
DMX linking:
DMXisalanguageallowingallmakesandmodelsofdifferentmanufacturestobelinkedtogether
andoperatefromasinglecontroller,aslongasallxturesandthecontrollerareDMXcompliant.
ToensureproperDMXdatatransmission,whenusingseveralDMXxturestrytousetheshortest
cablepathpossible.TheorderinwhichxturesareconnectedinaDMXlinedoesnotinuencethe
DMXaddressing.Forexample;axtureassignedtoaDMXaddressof1maybeplacedanywherein
aDMXline,atthebeginning,attheend,oranywhereinthemiddle.Whenaxtureisassigneda
DMXaddressof1,theDMXcontrollerknowstosendDATAassignedtoaddress1tothatunit,
nomatterwhereitislocatedintheDMXchain.
DATA cable (DMX cable) requirements (for DMX operation):
ThisxturecanbecontrolledviaDMX-512protocol.TheDMXaddressissetonthebackoftheunit.
YourunitandyourDMXcontrollerrequireastandard3-pinXLRconnectorfordatainput/output,
seeimagebelow.
Note: DMX cable must be daisy chained and cannot be split.
DMX setup
FurtherDMXcablescanbe
purchasedfromallgoodsound
andlightingsuppliersor
ProLightConceptsdealers.
Pleasequote:
CABL10 – 2m
CABL11 – 5m
CABL12 – 10m

www.prolight.co.uk 150W COB CW/WW Par User Manual 10
Notice:
Besuretofollowthediagramsbelowwhenmakingyourowncables.Donotconnectthecables
shieldconductortothegroundlugorallowtheshieldconductortocomeincontactwiththeXLRs
outercasing.Groundingtheshieldcouldcauseashortcircuitanderraticbehaviour.
Special note:
Line termination:
Whenlongerrunsofcableareused,
youmayneedtouseaterminatoron
thelastunittoavoiderraticbehaviour.
Using a cable terminator will decrease
the possibilities of erratic behaviour.
(3-pin - Order ref: CABL90, 5-pin - Order ref: CABL89)
5-pin XLR DMX connectors:
Somemanufacturesuse5-pinXLRconnectorsfordatatransmissioninplaceof3-pin.5-pinXLRxtures
maybeimplementedina3-pinXLRDMXline.Wheninsertingstandard5-pinXLRconnectorsintoa
3-pinlineacableadaptormustbeused.Thediagrambelowdetailsthecorrectcableconversion.
Terminationreducessignaltransmission
problemsandinterference.Itisalways
advisabletoconnectaDMXterminal,
(resistance120Ohm1/4W)betweenpin2
(DMX-)andpin3(DMX+)ofthelastxture.
5-pin XLR (socket)
Pin 1: GND (screen)
Pin 2: Signal (-)
Pin 3: Signal (+)
Pin 4: N/C
Pin 5: N/C
3-pin XLR (socket)
Pin 1: GND (screen)
Pin 2: Signal (-)
Pin 3: Signal (+)
3-pin XLR (socket)
Pin 1: GND (screen)
Pin 2: Signal (-)
Pin 3: Signal (+)
5-pin XLR (socket)
Pin 1: GND (screen)
Pin 2: Signal (-)
Pin 3: Signal (+)
Pin 4: N/C
Pin 5: N/C
DMX setup

www.prolight.co.uk 150W COB CW/WW Par User Manual 11
WEEE notice
Correct Disposal of this Product
(Waste Electrical & Electronic Equipment)
(Applicable in the European Union and other European countries
with separate collection systems)
Thismarkingshownontheproductoritsliterature,indicatesthatitshouldnotbedisposed
withotherhouseholdwastesattheendofitsworkinglife.Topreventpossibleharmtothe
environmentorhumanhealthfromuncontrolledwastedisposal,pleaseseparatethisfromother
typesofwastesandrecycleitresponsiblytopromotethesustainablereuseofmaterialresources.
Householdusersshouldcontacteithertheretailerwheretheypurchasedthisproduct,ortheir
localgovernmentofce,fordetailsofwhereandhowtheycantakethisitemforenvironmentally
saferecycling.
Businessusersshouldcontacttheirsupplierandcheckthetermsandconditionsofthe
purchasecontract.Thisproductshouldnotbemixedwithothercommercialwastesfordisposal.

www.prolight.co.uk 150W COB CW/WW Par User Manual 12