Emerson 814-3560 User manual

Document Part # 026-4842 Rev 1 Page 1 of 4
©2017 Emerson Climate Technologies Retail Solutions, Inc. This document may be photocopied for personal use.
Visit our website at http://www.emersonclimate.com/ for the latest technical documentation and updates.
Product Description
The Emerson Wireless Repeater (P/Ns 814-3560 and 814-3570) is the recommended repeater to be used with the Wireless
Module System. If a Wireless Module is placed more than 100 feet from the Wireless Gateway, a Wireless Repeater should be
added to optimize the wireless range between devices. The Repeater should be placed between the Gateway and the Module.
The best location is a clear line-of-sight between the two units if possible.
Specifications
Mounting and Wiring
• Install outside a standard electrical box.
• Clear line-of-sight between Wireless Gateway and Wireless Module and/or 3rd party wireless
transmitters.
• Use the included double-sided adhesive pad to mount the Repeater once configured.
Power Supply Weight
P/N 814-3560 9V to 30VAC,
12 to 40VDC 1.9oz (54g)
P/N 814-3570 120V to 277VAC,
50/60 Hz 3.9oz (90g)
Wireless Frequency 902MHz
Dimensions 2.57" H x 1.65" W x 1.10" D
(6.5cm x 4.2cm x 2.8cm)
Temperature Range Indoor use only
32°F to 104°F (0°C to 44°C)
Relative Humidity 20% to 95% non-condensing
Installation Guide
Wireless Repeater

Document Part # 026-4842 Rev 1 Page 2 of 4
©2017 Emerson Climate Technologies Retail Solutions, Inc. This document may be photocopied for personal use.
Visit our website at http://www.emersonclimate.com/ for the latest technical documentation and updates.
P/N 814-3560
• Black/Red: 9 to 30 VAC; 12 to 40 VDC
• Yellow: No Connection
P/N 814-3570
• Black: 120V to 277V VAC; 50/60 Hz
• White: Neutral
• Red: No Connection
Note: It may be easier to configure the Repeater and Modules before mounting the devices.
Set Up the Repeater
• The setup interface has two buttons, Menu and Set. Each has a corresponding three-color LED (green, amber, red).
• The buttons and LEDs are used to navigate and select linking and setup options through a three-tier menu system consist-
ing of different Modes>Menu>Options.
• The LEDs respond by showing solid or blinking lights of different colors to indicate active options and pending changes.
• The illustration and legend below describe how the buttons are used and the meaning of the LED responses.
1. Power up the Repeater. It will initiate the startup LED sequence.
2. Configure the device as a Repeater.
3. Link any 3rd party transmitters.
Configure the Repeater
Note: The Emerson Wireless Repeater comes pre-configured as a 1 Hop repeater.
1. Access the Advanced Setup menu by holding down both buttons for five (5) seconds until both LEDs turn amber.

Document Part # 026-4842 Rev 1 Page 3 of 4
©2017 Emerson Climate Technologies Retail Solutions, Inc. This document may be photocopied for personal use.
Visit our website at http://www.emersonclimate.com/ for the latest technical documentation and updates.
2. When Setup mode is entered, the Menu LED blinks red and the Set LED blinks green.
3. Select 1 Hop by quickly pressing the Set button twice and the Set LED will blink amber twice, or select 2 Hops by quickly
pressing the Set button three (3) times and the Set LED will blink amber three times.
4. To exit Advanced Setup Mode and return to normal operation, press and hold both buttons for
two (2) seconds and both LEDs will blink green to confirm.
Link a 3rd Party Transmitter to a Repeater
Note: If an Emerson Module or Sensor is being used, the Repeater automatically links to the device and repeats the transmission once it
is powered up and configured.
1. To access Basic Setup Mode, press and hold both buttons for two (2) seconds until both LEDs are green.
When the Repeater is ready to accept a link, both LEDs blink once per second.
Note: Once activated, this option stays active for two (2) minutes to provide time to link multiple devices.
2. For the transmitter to be linked to the repeater, press the Link button on that device. The Module is linked successfully
when the Set LED displays solid green for three (3) seconds.
Option Description
1 Hop More than 20 Transmitters near a Repeater
2 Hop Less than 20 Transmitters near a Repeater

This document may be photocopied for personal use.
Visit our website at http://www.emersonclimate.com/ for the latest technical documentation and updates.
Join Emerson Retail Solutions Technical Support on Facebook. http://on.fb.me/WUQRnt
The contents of this publication are presented for informational purposes only and they are not to be construed as warranties or guarantees, express or implied, regarding the products or services described herein or their use or
applicability. Emerson Climate Technologies Retail Solutions, Inc. and/or its affiliates (collectively “Emerson”), reserves the right to modify the designs or specifications of such products at any time without notice. Emerson does
not assume responsibility for the selection, use or maintenance of any product. Responsibility for proper selection, use and maintenance of any product remains solely with the purchaser and end-user.
026-4842 Emerson is a trademark of Emerson Electric Co. ©2017 Emerson Climate Technologies Retail Solutions, Inc. All rights reserved.
Document Part # 026-4842 Rev 1 Page 4 of 4
The Repeater is ready to accept new links when both LEDs blink once per second again.
3. To exit Basic Setup mode and return to normal operation, press and hold both buttons for
two (2) seconds and both LEDs will blink green to confirm.
To Unlink a 3rd Party Transmitter
Follow the same steps as described to link a Module to a Repeater:
1. To access Basic Setup Mode, press and hold both buttons for two (2) seconds until both LEDs are green.
2. Press the Set button three (3) times to access the Remove Link option. When the Repeater is ready to remove links, the
Menu LED will blink once and the Set LED will blink three (3) times.
3. Press the Learn button on the Module that is to be removed. The Set LED will illuminate red briefly to indicate the link was
successfully removed.
4. To exit Basic Setup Mode and return to normal operation, press and hold both buttons for
two (2) seconds and both LEDs will blink green to confirm.
To Restore Factory Defaults
Follow the steps below to restore the factory defaults to the Repeater:
1. Press and hold both buttons for 15 seconds until the Menu LED is solid red and the Set LED is solid amber.
Note: Both LEDs will turn various colors as the repeater cycles through the resetting process.
2. Press and hold the Set button for three (3) seconds to confirm the reset.
3. The Repeater will reboot and initiate the startup LED sequence.
4. Once the startup sequence is complete, refer to the Configure the Repeater section of this document to set up the device
again.