Eminent EM8650 User manual

EM8650
Pet immune PIR Motion Detector 2-way
Downloaded from www.vandenborre.be

2
|
ENGLISH
EM8650 - Pet immune PIR Motion Detector
Table of contents
1.0 Introduction ...........................................................................................................2
1.1 Packing contents...............................................................................................2
2.0 Front of motion detector.........................................................................................3
3.0 Inside the motion detector .....................................................................................3
3.1 Infrared sensors.................................................................................................3
3.2 Anti sabotage button..........................................................................................4
3.3 LED On/Off........................................................................................................4
3.4 Group settings (jumpers)...................................................................................4
4.0 Rear motion detector.............................................................................................5
4.1 Test mode .........................................................................................................5
4.2 Activated ...........................................................................................................5
4.3 Pair the motion detector.....................................................................................5
5.0 Installation tips.......................................................................................................5
6.0 Test the motion detector........................................................................................6
7.0 Frequently Asked Questions and other related information....................................6
8.0 Service and support...............................................................................................7
9.0 Warning and points of attention .............................................................................7
10.0 Warranty conditions.............................................................................................8
1.0 Introduction
Congratulations with the purchase of this high-quality Eminent product! This product
has undergone extensive testing by Eminent’s technical experts. Should you
experience any problems with this product, you are covered by a five-year Eminent
warranty. Please keep this manual and the receipt in a safe place.
Register your product now on www.eminent-online.com and receive product updates!
1.1 Packing contents
The following parts need to be present in the packing:
•EM8650 Dual Wireless Motion Detector
•Manual
•Screws
•Plugs
•Mounting bracket
Downloaded from www.vandenborre.be

3
|
ENGLISH
2.0 Front of motion detector
LED indicator :
Flashes continuously : Motion detector is performing a self-test
Flashes 1x : Motion detected
Flashes 2x : Self-test completed. Motion detector is active
Flash once per 3 seconds : Battery power low, exchange battery*
* You will receive a text message if battery level is low. The message contains the
following information (up to sensor 9) Sensor name with additionally the text ‘battery
almost empty’. From sensor 10 the name will be replaced by a zone nr. with
additionally the text ‘battery almost empty’.
3.0 Inside the motion detector
Remove the screw on top of the motion detector and gently remove the front and
back.
3.1 Infrared sensors
The infrared sensors detect the motion. These sensors need to be clean at all time.
Do no touch the sensors !
1. Detection window
2. LED indicator
3. Mounting bracket
LED On/Off
Infrared sensor
Group setting (jumpers)
Anti sabotage
button
Infrared sensor
Downloaded from www.vandenborre.be

4
|
ENGLISH
3.2 Anti sabotage button
If the motion detector is opened this switch will detect it and trigger the alarm.
3.3 LED On/Off
By switching this jumper setting you can set if the LED in front of the motion detector
will be switched “On or Off”. By default this setting is turned ON (LED ON).
3.4 Group settings (jumpers)
Every sensor can be configured to be added to a dedicated group by setting the
jumper settings; home-group, normal group, single group or 24-hours group.
Bellow you will see an overview of the meaning and how to configure the jumper
settings for that type of zone.
Remark : Determine before pairing with the alarm system in which group the sensor
will be operational. Once the sensor is successfully paired with the system. The group
cannot be changed after pairing!
Remark: If the group of a sensor needs to be changed, all sensors need to be paired
with the alarm system once more. It is not possible to remove one single sensor from
a group ! (See chapter “Delete all wireless sensors by text message”)
Remark : It’s recommended to install detectors that needs to be operational 24-hours,
for example smoke detectors, in the 24-hours-group.
24-hours-group
Home-group
Normal-group
Single-group
Downloaded from www.vandenborre.be

5
|
ENGLISH
4.0 Rear motion detector
4.1 Test mode
After the self-test has finished press the test button once. The motion detector will
send a trigger signal (flashes 1x).
4.2 Activated
If the motion sensor is triggered more than 2 times within 3 minutes the device
switches automatically to power saving mode. The motion detector will activate again
if it does not register motion for a time period of 3 minutes.
4.3 Pair the motion detector
Enter the password and press button on the control panel.
The LED will turn on. Press 2x the test button of the motion detector you wish to
register. If you hear a beep the sensor is registered to the system. If you hear 2
beeps this indicates this sensor is already registered.
Notice: During the registration process be sure no other sensor is triggered. If a
motion detector is in the same room make sure you cover the motion detector or place
the motion detector temporarily in a different room.
5.0 Installation tips
Avoid installation of the motion detector in range of a window, air-conditioning,
radiator, refrigerator, oven, direct sunlight or other places with high temperature
fluctuation.
Do not place 2 motion detectors facing each other or within each other’s range.
Motion detectors are usually placed at 2 meters from the floor on the wall.
Test button
Downloaded from www.vandenborre.be

6
|
ENGLISH
First install the mounting bracket before placing the motion detector in the bracket.
Point the detector in the direction you wish to secure. Test if the motion detector is
working properly in test mode.
6.0 Test the motion detector
After you fully installed the motion detector and the self-test is completed you can test
the motion detector by walking within the range of the motion detector from one side to
the other side. The LED indicator of the motion detector will flash if motion is detected.
Adjust the motion sensor to get the best results. And repeat the test.
7.0 Frequently Asked Questions and other related
information
The latest Frequently asked questions for your product can be found on the support
page of your product. Eminent will update these pages frequently to assure you have
the most recent information. Visit www.eminent-online.com for more information about
your product.
Top view
Side view
floor
Side view
Downloaded from www.vandenborre.be

7
|
ENGLISH
8.0 Service and support
This user manual has been carefully written by Eminent’s technical experts. If you have problems
installing or using the product, please fill out the support form at the website www.eminent-
online.com/support.
You can also contact us by phone. Please check www.eminent-online.com/support for the
helpdesk phone number and opening hours.
9.0 Warning and points of attention
Due to laws, directives and regulations set out by the European parliament, some (wireless)
devices could be subject to limitations concerning its use in certain European member states. In
certain European member states the use of such devices could be prohibited. Contact your (local)
government for more information about this limitations.
Always follow up the instructions in the manual*, especially where it concerns devices which need
to be assembled.
Warning: In most cases this concerns an electronic device. Wrong/improper use may lead to
(severe) injuries!
When you connect the device to the mains, make sure it will not be damaged or subject to (high)
pressure.
A power socket is needed which should be close and easy accessible from the device.
Repairing of the device should be done by qualified Eminent staff. Never try to repair the device
yourself. The warranty immediately voids when products have undergone self-repair and/or by
misuse. For extended warranty conditions, please visit our website at www.eminent-
online.com/warranty.
Dispose of the device appropriately. Please follow your countries regulation for the disposal of
electronic goods.
Please check below safety points carefully:
- Do not apply external force on the cables
- Do not unplug the device by pulling the power cable
- Do not place the device near heating elements
- Do not let the device come in contact with water of other liquids
- If there is any strange sound, smoke or odor, remove the device immediately from the power
outlet.
- Do not put any sharp objects into the venting hole of a product
- Do not use any damaged cables (risk of electric shock)
- Keep the product out of reach of children
- Wipe off the product with soft fabric, not water mop.
- Keep the power plug and outlet clean
- Do not unplug the device form the power outlet with wet hands
- Unplug the device when you don’t use it for a long time
- Use the device at a well ventilated place
*Tip: Eminent manuals are written with great care. However, due to new technological
developments it can happen that a printed manual does not longer contain the most recent
information. If you are experiencing any problems with the printed manual or you cannot find what
you are looking for, please always check our website www.eminent-online.com first for the newest
updated manual.
Also, you will find frequently asked questions in the FAQ section. It is highly recommended to
consult the FAQ section. Very often the answer to your questions will be found here.
Downloaded from www.vandenborre.be

8
|
ENGLISH
10.0 Warranty conditions
The five-year Eminent warranty applies to all Eminent products, unless mentioned otherwise
before or during the moment of purchase. After buying a second-hand Eminent product the
remaining period of warranty is measured from the moment of purchase by the product’s initial
owner. Eminent warranty applies to all Eminent products and parts, indissolubly connected or
mounted to the product it concerns. Power supply adapters, batteries, antennas and all other
products not directly integrated in or connected to the main product or products of which, without
reasonable doubt, can be assumed that wear and tear during use will show a different pattern than
the main product, are not covered by the Eminent warranty. Products are not covered by the
Eminent warranty when exposed to incorrect/improper use, external influences or when opening
the service parts of the product by parties other than Eminent. Eminent may use refurbished
materials for repair or replacement of your defective product. Eminent cannot be held responsible
for changes in network settings by internet providers. We cannot guarantee that the Eminent
networking product will keep working when settings are changed by the internet providers.
Eminent cannot guarantee the working of web services, apps and other third party content that is
available through Eminent products. Eminent products with an internal hard disk have a limited
warranty period of two years on the hard disk. Eminent could not be held responsible for any data
lost. Please make sure that if the product stores data on a hard drive or other memory source, you
will make a copy before you return the product for repair.
When my product gets defective
Should you encounter a product rendered defective for reasons other than described above:
Please contact your point of purchase for taking care of your defective product.
EM8650_EN | 06-2016
Downloaded from www.vandenborre.be