EMP-Centauri G1/1ECN-1 User manual

Examples of setting of generator G1/1ECNman-1:
choice of sat. position B
(second LNB)
levers setting:
opt OFF
pos ON
pol, band OFF
choice of sat. position C
(third LNB)
levers setting:
opt ON
pos OFF
pol, band OFF
choice of sat. position D
(fourth LNB)
levers setting:
opt ON
pos ON
pol, band OFF
Dear Customer,
congratulations on the purchase of the MP-Centauri product. Before its installation and putting
into operation, read carefully the entire operation manual. Keep the purchase and rework (if any)
records for future need.
1 The area of application, warrant
The product is designed for distributing satellite, terrestrial TV and radio signals. We
recommend the device to be installed and serviced b the qualified technician. MP-Centauri
CONOMY CLASS products are covered under warranty for up to 4 (four) years from the date
of purchase. The warranty shall not apply to the product used for other than specified purpose.
The user will be responsible for injury or material damage which may arise in consequence of
any product use in contradiction with the manual. It is prohibited and unlawful to dismantle the
product and make any interventions in it. Repairs of the product may be performed only by MP-
Centauri company, or other companies authorized by MP-Centauri.
2 Technical specifications
1in/1out DiS qC 1.0 generators. Generators are controlled by means of DC voltage on 4 cinch
(RCA) sockets (0/12 V DC, G1/1 CN-1) or 4 manual flip-flop switches (G1/1 CNman-1).
SPECIFICATIONS G1/1ECN-1 G1/1ECNman-1
Number of inputs 1
Number of outputs 1
Frequenc range SAT 950-2150 MHz
Insertion loss (avg) SAT 2 dB
Current consumption (avg) 40 mA (18 V DC) from receiver
Dimensions (w,d,h) 7.6 x 4.4 x 2.8 cm 7.6 x 3.6 x 4.3 cm
Temperature range –25 °C - +60 °C
3 Product takeover
Make sure that the product is not damaged. In the case of damage please contact your dealer.
4 Product storing and installations
The product must not be stored and installed
•in the place with excessive humidity,
•in the place with dropping or running water,
•in the place with high dust pollution, mechanical vibrations or impacts,
•in the place out of temperature limits specified in the section 2 Technical specifications,
INSTRUCTION MANUAL 1/002903 B
G1/1 CN-1
G1/1 CNman-1
Contact
MP-Centauri s.r.o.
5. kvetna 690
339 01 Klatovy 1
Czech Republic
tel: [phone]
fax: [phone]
[email protected]
www.emp-centauri.eu
návod k použití G1/1 CN-1, G1/1 CNman-1 CZ stav změn : B
datum : 16. 2. 2011
FQ 7.3-1_027
vypracoval : P. Hajčiar přezkoušel : J. Pernikl schválil : M. Váňa
podpis : podpis : podpis :
1 of 4
4 of 4

•close to heat sources (e.g. radiators or air ventilators, direct sunshine)
•in the reach of children.
Connect the product's inputs and outputs firmly to the coaxial cable.
•nsure the free space for the air circulation (space on sides and bellow the product
should be at least 20 cm and the space over its top at least 50 cm).
•Do not cover the product (e.g. with curtains etc.).
•Do not place any containers with liquids (vases, glasses etc.) or naked flame sources
(lighted candle etc.) on the product.
5 Product connection
Connect the product in accordance with this manual and valid regulation. To connect the product
inputs and outputs use high-quality 75 Ω coaxial cable designed for satellite (or terrestrial)
reception. The coaxial cables shall not be broken, the minimum bending radius shall be 5 cm.
Mount the F connectors on the ends of cables. You can use screw, crimp or compress types of
connectors. Connect the cables into the F sockets of product and fasten them with an appropriate
force.
•interconnect F socket marked IN with output of multiswitch
•interconnect F socket marked OUT with input of satellite receiver.
• interconnect chosen cinch socket with output DC 0/12 V of satellite receiver (G1/1 CN-1
only).
The wiring examples are shown in the section 10 Wiring diagrams or at the website www.emp-
centauri.eu.
6 Product settings
Generator generates at F socket marked IN analog commands + commands DiS qC 1.0,
depending on voltage at cinch sockets (G1/1 CN-1) or on position of switches (G1/1 CNman-1).
voltage at cinch socket, position of switch command at F socket marked IN
cinch socket 1 (0/12 V), switch 1 (OFF/ON) 0 00 38 F0/1 + 0/22 kHz (low/high band)
cinch socket 2 (0/12 V), switch 2 (OFF/ON) 0 00 38 F0/2 (vertical/horizontal polarization)
cinch socket 3 (0/12 V), switch 3 (OFF/ON) 0 00 38 F0/4 + tone burst 0/1 (“position” 0/1)
cinch socket 4 (0/12 V), switch 4 (OFF/ON) 0 00 38 F0/8 (“option” 0/1)
Generator repeats commands received from F socket marked OUT to F sockets marked IN. Final
command at F sockets marked IN is result of “OR” function of command at F socket marked OUT
and command generated by generator. In addition to commands DiS qC 1.0 are added analog
commands (except polarization), in addition to analog commands are added commands DiS qC 1.0.
7 Safet
Make sure the antennas are grounded properl .
Connect all devices to power grid onl after all connections are finished and checked.
Never work on the product, TV set or other powered products during or before a storm!
A lightning stroke into the antenna ma cause dangerous overvoltage in the product
metallic parts.
If the product gets into contact with liquids (e.g. dropping water or spilled drinks) it should
be disconnected from the grid immediatel .
8 Product maintenance
Maintenance consists especially of cleaning of the product.
Alwa s disconnect power suppl cables of all installed products when performing an
maintenance on the product. If ou have to enter places with a risk of fall, pa attention to
our safet .
Use only dry cloth to clean the product and do not use any liquid agents.
Coaxial cables installed outdoors should be replaced once in a few years. very 2 years unscrew
the coaxial cable and clean connector contacts or shorten the coaxial cable by approx. 2 cm.
9 S mbols explanation
Certificate of conformity
DiS qC (Digital Satellite quipment control) – international standard for digital
satellite equipment control, number (1.0, 1.1, 1.2 or 2.0) determines DiS qC
version.
According to U directive, electric and electronic devices which are identified by
one of the following symbols must not be disposed of together with municipal
waste. When disposing of the old device, use local waste collection and separation
systems.
10 Wiring diagrams
3 of 4
2 of 4