EMS FireCell FC-200-003 User manual

Wireless Manual Call Point (Apollo Front)
Installation Guide
Part no
FC-200-003
Description
Wireless Manual Call Point (Apollo Front)
1 Pre installation 2 Components
!Installation must conform to applicable local installation codes
and should only be installed by a fully trained competent person.
• Ensure that the device is installed as per the site survey.
• The use of a non-metallic spacer should be considered if mounting the
device on to a metal surface.
• Do NOT Press the Log On button on a pre-programmed device, as this
will cause communication with the Control Panel to be lost. Should this
happen, delete the device from the system and add it back on.
• This device contains electronics that may be susceptible to damage
from Electrostatic Discharge (ESD). Take appropriate precautions when
handling electronic boards.
3 Fix mounting plate 4 Power device
5 Device locking 6 Conguration
©2022 EMS Ltd. All rights reserved. Page 1 of 2 MK289-99 Issue 4 21/06/2022 AJM
REMOVE LABEL ON COMMISSIONING
REMOVAL RESET
1 2
3
4 5
1Reset key, 2Transparent cover, 3Fixing screw,
4Wireless call point, 5Mounting plate
• Remove the mounting plate from the wireless call point. See Step 5 for
more information on unlocking the device.
• Ensure mounting plate is tted in the orientation shown.
• Use both mounting holes.
• Use suitable fasteners and xings.
67 mm
57 mm
• When tting / replacing batteries; observe correct polarity, using only
specied batteries.
• Connect the power jumper across the PIN header.
• Once powered, reassemble the device.
SIZE AA
SIZE AA
SIZE AA
SIZE AA
SIZE AA
SIZE AA
device
unpowered
(pins unlinked)
device
powered
(both pins linked)
• To open the call point, loosen
the xing screw, then slide the
call point up, away from the
mounting plate.
• When reassembling, observe the
hinged connection located on
the devices top edge rst, prior
to closing the unit. Finally lock
the call point into the mounting
plate by tightening the xing
screw.
Fixing screw
Bottom view of
device
The device’s loop address is congured within the user interface’s menu
structure.
• Refer to the programming manual for full programming details.
FireCell = MK98
Fusion = TSD062
WZM = TSD143
Free to download from
www.emsgroup.co.uk

Device activation
Device resetting
Specication Regulatory information
©2022 EMS Ltd. All rights reserved. Page 2 of 2 MK289-99 Issue 4 21/06/2022 AJM
1 2 3
(with transparent cover lifted)
Alarm LED
illuminated and re
event is displayed at
the control panel.
1 2 3
Alarm LED illuminated (with transparent cover lifted)
Turn the reset key
clockwise to reset Element returns
to the normal
position
Operating temperature -10 to +55 °C
Storage temperature 5 to 30 °C
Humidity 0 to 95% non-condensing
Supply 6x AA alkaline (Panasonic LR6AD Powerline
/ Varta 4006 Industrial)
CAUTION!
Fitting of an incorrect battery type invalidates the product certication and may
result in poor performance.
IP rating IP24
Operating frequency 868 MHz
Output transmitter power Auto adjusting 0 to 14 dBm (0 to 25 mW)
Signalling protocol X
Dimensions (W x H x D) 90 x 98 x 72.5 mm
Weight 0.35 kg
Location Type A: For indoor use
Manufacturer
Year of manufacture
Certication
Certication body
CPR DoP
Approved to
European Union
Directives
EN54-11:2001. Incorporating Amendment No. 1 and
Corrigendum No. 1. Fire detection and re alarm systems.
Part 11: Manual call points.
EN54-25:2008. Incorporating corrigenda September 2010
and March 2012. Fire detection and re alarm systems.
Part 25: Components using radio links.
EMS declares that this device is in compliance with
Directive 2014/53/EU. The full text of the EU declaration of
conformity is available at the following internet address:
www.emsgroup.co.uk
2012/19/EU (WEEE directive): Products marked with this
symbol cannot be disposed of as unsorted municipal waste
in the European Union. For proper recycling, return this
product to your local supplier upon purchase of equivalent
new equipment, or dispose of it at designated collection
points. For more information see www.recyclethis.info
Dispose of your batteries in an environmentally friendly
manner according to your local regulations.
Carrier Manufacturing Poland Sp. z o.o.
Ul. Kolejowa 24. 39-100 Ropczyce, Poland
See devices serial number label
0359-CPR-00694
0905
19