Endon EL-KALAMOS User manual

The Light pack contains:
IP rated wall mirror with proximity switch and
demister.
The following tools may be required:
Selection of cross and flat head screwdrivers.
Electric drill and assorted drill bits.
Wire strippers.
Electrical insulation tape.
INSTRU TION MANUAL
These products are only suitable for connection to a 240V~50Hz supply in accordance with current
IEE wiring Regulations and should be installed in accordance with local Building Regulations and
are for Domestic wall use only.
These mirror lights have an IP44 rating and may be installed in “Zones 1 and 2 and Outside Zones”
of a bathroom and the supply circuit protected by an R D.
These zones are referenced in BS 7671: 2008 “Requirements for Electrical Installations”, IEE Wiring
Regulations 17th Edition – see associated diagram.
These mirror lights should be connected to a lighting circuit protected by a 5 amp fuse (or a 6 amp
miniature circuit breaker) and an R D when the fittings are used in a bathroom.
If in doubt we recommend you contact a qualified electrician.
Be careful during handling and maintenance to avoid breakage of the glass parts.
lean with a dry cloth only. Do not use liquid or abrasive cleaners on this product.
If the glass cover (mirror) is broken or cracked then it must be replaced immediately to preserve the
water ingress protection, please consult your retailer. This is represented by the symbol
These fittings are heavy and you will require assistance in connecting them to the supply and
securing them to the mounting surface.
These mirrors have (non-replaceable) LED`s fitted. We recommend that you do not stare directly into
the LED light beams.
If any modification is made it will invalidate the warranty and may render the product unsafe.
Before you start
Please read these instructions carefully before fitting your new mirror and retain for reference.
Make sure that there are no pipes or cables beneath the mounting surface.
Make sure that there is a 200mm space between the sensor and any other surface eg sink, shelf etc.
Switch off the mains supply and remove the appropriate fuse or switch off the appropriate circuit
breaker before commencing installation.
Ensure that no one else has access that would enable the supply to be inadvertently reconnected.
Check the packaging and make sure that you have all the re uired parts.
Follow each assembly step in order to prevent incorrect assembly.
Make sure all screws / nuts, including electrical connections etc are fully tightened before use.
This mirror should not be connected to a Dimmer.
1
EL-KALAMOS AND EL-KASTOS MIRRORS
Safety Warnings
NOTE:-
1. A shower tray is shown here,
a bath has equivalent
dimensions.
2. Basins should be re arded as
havin a 600mm Zone 2
hemi-sphere above and
extendin down to the floor.
(If in doubt refer to the latest
edition of BS 7671, or a
qualified electrician).

Assembly/ User Instruction
Endon lighting Ltd.
Leeds.
UK
LS9 0SE
1. Decide on the position of the mirror light,
making sure there is a 200mm gap between
the sensor and any other surface – eg sink,
shelf etc. Ensure there is a solid mounting
surface, preferably a brick or block wall and
ensure that there are no cables or pipes
beneath the surface (except for the mirror
supply cable). If the wall is timber frame and
plasterboard then please use appropriate
fixings. Ensure the fixings used can support the
weight of the mirror.
2. Diagram 1. Remove the mirror front by
removing the 4 side screw assemblies, retain
these for re-use. Gently pull apart the demister
pad plug / socket (A) and remove the mains in
terminal block connection cover (B).
3. Diagram 2. Offer the back plate to the
mounting surface and determine the position of
the cable entry. Mark out the 4 mounting
positions as shown (C). Drill and plug the
mounting surface. Bring the mains cable
through the rubber grommet in the back
housing and secure the back housing to the
mounting surface – making sure that the sides
are vertical and the top is horizontal.
IMPORTANT: The rubber grommet must be
used at the cable entry point to ensure that the
water ingress protection of the fitting is
maintained.
4. Diagram 3. Connect the house wiring to the
terminal block. NOTE: This is a lass I fitting
and must be earthed. Cut and strip the mains
cable and connect it to the terminal block as
shown – see WIRING DETAILS. Re-fit the
terminal block cover (B).
5. Diagram 4. Re-connect the moulded male /
female connectors from the demister – (A).
6. Re-fit the mirror front making sure any
silicone seals are correctly positioned – to
protect the fitting against water ingress and that
no cables are trapped -then secure in position
with the 4 screw assemblies removed in 2
above.
7. Turn on the power and test the proximity
switch.
These assembly diagrams are intended as a guide – if in doubt consult a qualified electrician. The EL-
KALAMOS mirror is shown here but the same installation steps apply to the EL-KASTOS.
2
Y20 12v2
Dia ram 1
Dia ram 2
Dia ram 3
Dia ram 4
WIRING DETAILS
Cable entry grommet
(A)
(B)
Mains in cable
(C) (C)
(C) (C)