ENEL JuiceBox Next Gen User manual

JuiceBox Next Gen
Time Saver Install Guide
ENGLISH

2
REV. 1
Table of contents
JuiceBox Next Gen 3
Package Contents 4
Installation Prerequisites 4
Overview 4
Location 5
Wiring And Circuit Requirements 5
Installation 6

3
REV. 1
JuiceBox Next Gen
Next Generation JuiceBox 32A, 40A, 48A or 80A
Wi-Fi enabled Sma Level 2 EVSE with 25-foot cable:
>LED indication for power, connectivity, charging status
>Durable, water and re-resistant metal case
NOTE: The product information in this document is veried to be accurate
and complete at the time of its publication. However, due to ongoing product
improvement, this information is subject to change at any time without prior
notice. For the latest information, see our documentation online at hps://
suppo-emobility.enelx.com/hc/en-us/aicles/360061880372-Welcome-to-
JuiceBox-Pro

4
REV. 1
>Wall bracket
>2 wall bracket screws (#10 self-tapping Phillips head wood screws)
>2 screws to hang JuiceBox onto wall bracket (#10-32 Phillips head machine screws)
>1 RFID card (except 80A)
Installation Prerequisites
Overview
JuiceBox requires either a hardwired electrical connection or a NEMA 14-50 outlet.
The JuiceBox power supply must be connected to a circuit breaker that is rated for at least
125% of the device's continuous load.
Package Contents
>JuiceBox
NOTE: In some markets, JuiceBox arrives secured to a cable holder that includes
keys.
NOTE: Ensure that all power connection wiring conforms to the rules and
regulations of any national and local codes.
>The JuiceBox may require a disconnecting means if:
> Not within line of sight of the Electrical Panel
> Required by local code
>Hardwire version: Only the pre-installed, hard wire whip shall be used to connect to a
junction box or disconnect. It is not long enough, nor is it meant to go directly into the
electrical panel.

5
REV. 1
CAUTION: Do NOT drill any additional holes into the JuiceBox enclosure as it
can cause damage to the PCB and/or electronics inside.
Location
When selecting a location to install the hardwire connection or outlet, keep in mind that
JuiceBox should be positioned:
>Within reach of the vehicle's charge po
>18 inches above the oor or ground
>If applicable, within range of a cellular connection or the local Wi-Fi network
Wiring And Circuit Requirements
>For additional specications, refer to the Specications section.
32A 40A 48A 80A
Circuit
Requirements
40 Amp 50 Amp 60 Amp 100 Amp
2 pole breaker 2 pole breaker 2 pole breaker 2 pole breaker
NOTE: For the installation wiring, please have your electrician size the conductors
for both rated wire temperature and 125% continuous load. Please refer to both
the National Electrical Code (NEC) and your local Authority Having Jurisdiction
(AHJ) for any additional requirements.1
1The neutral wire is not used, but may need to be present in the receptacle.

6
REV. 1
Installation
Fully read and understand the directions before installation. Refer to impoant safety
information at the end of this document.
This section describes installing the JuiceBox Pro onto a wall mount. If installing onto a
JuiceStand, refer to the JuiceStand Manual.
1. Turn o the circuit breaker to the NEMA 14-50 outlet, NEMA 6-50 outlet, or hardwired
electrical connection.
WARNING: Do not continue this installation until the circuit breaker is turned
o.
2. Use a stud sensor to determine an appropriate mounting location, then use the 2 screws
to secure the wall bracket.
Version with cable holder Version without cable holder
3. Inse the enclosure screws into the enclosure, as shown. Tighten the screws until
approximately 2 mm of thread are visible.

7
REV. 1
Version without cable holderVersion with cable holder
NOTE: : If the JuiceBox does not hang securely, adjust the screws that were
installed in step 3. The 48 and 80 amp are hardwire only and do not have a plug as
shown.
4 Hang the JuiceBox onto the wall bracket.
Version without cable holderVersion with cable holder
5. Connect the JuiceBox:
> Plug-In Version: Plug the JuiceBox into the NEMA 14-50 outlet or NEMA
6-50 outlet.
> 1-Phase Hardwired Version: Connect the harness to the junction box.

8
REV. 1
WARNING: It is the installers responsibility to ensure that the JuiceBox is wired
in accordance with the local electrical code.
NOTE: : The hardwire versions of the JuiceBox are shipped with appropriate wires
that meet the National Electric Code (NEC) NFPA 70 and require a nearby junction
box connection. Any alteration of the supplied wiring will invalidate the warranty
and may not conform to NEC.
32A/40A 48A 80A
L1 (Black) 8 AWG 6 AWG 3 AWG
L2 (Red) 8 AWG 6 AWG 3 AWG
Ground (Green) 8 AWG (THHN) 8 AWG (THHN) 6 AWG (THHN)
6. Turn on the circuit breaker that supplies power to the NEMA 14-50 outlet, NEMA 6-50
outlet, or hardwired electrical connection.