Enerwave ZWN-323 User manual

INSTALLATION INSTRUCTIONS
-01-
DESCRIPTION
FEATURES
ZWN-323
Plug-in Dimming Module
-02-
OPERATIONS
Manual Control
INSTALLATION
The four possible responses are:
- It will respond to ALL-ON and the ALL-OFF command (default).
- It will not respond to ALL-ON or ALL-OFF commands.
- It will respond to the ALL-OFF command but will not respond to the ALL-ON
command.
- It will respond to the ALL-ON command but will not respond to the ALL-OFF
command
All On/All Off
Depending upon your primary controller, the ZWN-323 Dimming Module can
be set to respond to ALL ON and ALL OFF commands in up to four different
ways. Some controllers may not be able to change the response from its
default setting. Please refer to your controller’s instructions for information
on whether or not it supports the configuration function and if so, how to
advanced controller. However, basic remotes do not have this capability.
Advanced Operation
The following Advanced Operation parameters require that you have an
change this setting.
WIRELESS RANGE
This device complies with the Z-Wave standard of open-air, line of sight
transmission distances of 100 feet. Actual performance in a home depends
on the numbers of walls between the remote controller and the destination
device, the type of construction and the number of Z-Wave enabled devices
installed in the control network.
-03-
Wireless Home Automation Control Device
After a power failure, the ZWN-323's Z-Wave controlled outlet
Please Note:
SPECIFICATIONS
WARNINGS AND CAUTIONS
To reduce the risk of electric shock, this product has a grounding
type plug that has a third (grounding) pin. This plug will only fit
into a grounding type power outlet. If the plug does not fit into the
outlet, connect a qualified electrician to install the proper outlet.
Do not change the plug in any way.
To be installed and/or used in accordance with appropriate electrical codes
and regulations. Exercise extreme caution when using Z-Wave devices to
control appliances. Operation of the Z-Wave device may be in a different
room than the controlled appliance, also an unintentional activation may
consult a qualified electrician.
occur if the wrong button on the remote is pressed. Z-Wave devices may
automatically be powered on due to timed event programming.Depending
upon the appliance, these unattended or unintentional operation could
If you are unsure or uncomfortable about performing the installation, please
possibly result in a hazardous condition.
Voltage................................................................................ 120VAC, 60Hz
Incandescent......................................................................................300W
Z-Wave Frequency.................................................................. 908.42 MHz
Operating Temperature............................................................ 32°F-104°F
Range.................................................................Up to 100 feet line of sight
between the Wireless Controller and the closest Z-Wave receiver module.
Interoperable with other Z-Wave enabled devices
One Z-Wave controlled and one always-on AC outlet
2. Attach the desired appliance into the Z-Wave controlled outlet on ZWN-323
Dimming Module.
3. Turn the knob/ program button on the lamp/ ZWN-323 module to ON position.
Basic Operation
1. With a Z-Wave remote.
2. Manually with the program button on the front of the ZWN-323.
Remote Control
Z-Wave remotes provide control of an Individual device, Groups of devices
and Scenes. Please refer to your remote control's instructions for detail on
its capabilities and instructions for adding and controlling devices.
Blue LED indicator
Z-Wave Controlled Outlet
Standard AC Outlet
Program Button
The Program Button on the ZWN-323 Dimming Module allows the user to:
Provides manual/ remote ON/OFF & Dim control of lamps connected
controlled outlet for the lamp and a always-on AC outlet for other device.
This ZWN-323 Dimming Module is a Z-Wave enabled device and is fully
interoperable with other Z-Wave certified device. In a Z-Wave network, the
ZWN-323 enable you to remotely ON/OFF&Dim control a Z-Wave
ZWN-323 also acts as a repeater, retransmitting the RF signal from one
device to another until the intended device is reached. With a horizontal
design, the ZWN-323 plug-in dimming module will not block other nearby
1. Plug the ZWN-323 Dimming Module into wall receptacle.
The connected appliance can be turned ON/OFF & Dim in two ways:
55
1. Manually turn ON the ZWN-323 Dimming Module, press and release the
program button. The blue LED indicator will turn OFF, and the lamp plugged
into the ZWN-323 Dimming Module will turn ON.
4. When the gateway/remote is in inclusion mode and the blue LED blinks on
55
3. Manually adjust the level of the connected lighting, press and hold the
program button. Release the button when the desired level is reached.
returns to OFF state. A lamp (25 watts minimum incandescent, 6 watts
can be controlled through Z-Wave controlled outlet.
Ease of installation(no new wiring)
Acts as a Z-Wave repeater to extend the range of Z-Wave network
AC outlets.
55
2. Manually turn OFF the ZWN-323 Dimming Module, press and release the
program button. The blue LED indicator will turn ON, and the lamp plugged
into the ZWN-323 Dimming Module will turn OFF.
ID for the module and the LED will turn OFF on the module. While the gateway/
Z-Wave network. The gateway/remote will verify the inclusion, assign a node
remote in exclusion mode, press the program button to remove from the current
Z-Wave network, and the LED will blink on the module.
the ZWN-323, press the program button to add the ZWN-323 module into
minimum dimmable LED )
Compatible with any incandescent, dimmable CFL and LED bulb
and small appliance

INSTALLATION INSTRUCTIONS
-05--04-
WARRANTY INFORMATION
the ALL-OFF command
Our company warranties its products to be free of defects in materials and
workmanship for a period of two (2) years. There are no obligations or
out of, or in connection with, the use or performance of this product or
other indirect damages with respect to loss of property, revenue, or profit,
or cost of removal, installation or reinstallation.
liabilities on the part of our company for consequential damages arising
Mar, 2014
Restoring Factory Defaults
All Configuration Parameters can all be restored to their factory default settings
by using your primary controller to reset the device.
Over-Current Protection
Additional over-current protection is provided by an internal fuse which is
not user serviceable. Check your home’s circuit breakers before concluding
that the product must be replaced.
Z-Wave Enabled Devices.
Effects of Home Construction on Wireless Range Between
The distances shown in the table below are typical examples. Actual
performance in your home will vary.
Note:
The equipment has been tested and found to comply with the limits
for a Class B Digital Device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment
uses, generates and can radiate radio frequency energy and, if not
installed and used in accordance with the instruction, may cause
harmful interference to radio communication. However, there is no
guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or
more of the following measures:
- Reorient or relocate the receiving antenna
- Increase the separation between the equipment and receiver
FCC COMPLIANCE STATEMENT
- This device may not cause interference
- This device must accept any interference, including interference that
Operation is subject to the following two conditions:
may cause undesired operation of the device.
- Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected
- Consult the dealer or an experienced radio/TV technician for
help.
- Wall mounted Z-Wave devices installed in metal junction boxes will suffer
a significant loss of range (approximately 20%) since the metal box blocks
a large part of the RF signal.
- Brick, tile or concrete walls block more of the RF signal than walls made
of wooden studs and plasterboard (drywall).
Things to consider regarding RF range:
- Each wall or obstacle (i.e.:refrigerator, big screen TV, etc.)between the
remote or a Z-Wave device and the destination device will reduce the
maximum range by approximately 25-30%.
11025A
From the Remote (or repeating Z-Wave module) to
destination device:
Type of
Construction
Wood Frame with
Drywall
Brick, Tile or
Concrete
Plastic
J-Boxes*
Metal
J-Boxes
Plastic
J-Boxes*
Metal
J-Boxes
Number of
Walls or
Obstacles
0** 100’ 80’ 100’ 80’
1 70’ 56’ 60’ 48’
2 49’ 39’ 36’ 29’
3 34’ 27’ 21’ 17’