ENFORCER EV-1665-N2BQ User manual

MANUAL
EV-1665-N2BQ
Wide Angle Bullet Camera
Note: Model numbers that end with “Q” or products that have a round green “Q” sticker signify RoHS compliance.
550 TV Lines
1/3”Sony Super HAD II CCD
2.2mm Lens with a 170° Viewing Angle
ENFORCER WIDE ANGLE BULLET CAMERA
IMPORTANT
Users and installers of this product are responsible for ensuring this product complies with all national, state, and local laws and
statutes related to monitoring and recording audio and video signals. SECO-LARM will not be held responsible for the use of this
product in violation of any current laws or statutes.
WARNING
Stop using the camera if you see a malfunction such as smoke or unusual heat, as it could cause fire or electric shock. Do not
open the case of this device, as there are no field serviceable components inside.
FCC COMPLIANCE STATEMENT
Information to the user: This equipment has been tested and found to comply with the limits for a class B digital device, pursuant
to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference when the
equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy
and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to
correct the interference at his own expense.
WARRANTY: This SECO LARM product is warranted against defects in material and workmanship while used in normal service
for a period of one (1) year from the date of sale to the original consumer customer. SECO LARM’s obligation is limited to the
repair or replacement of any defective part if the unit is returned, transportation prepaid, to SECO LARM.
This Warranty is void if damage is caused by or attributed to acts of God, physical or electrical misuse or abuse, neglect, repair, or
alteration, improper or abnormal usage, or faulty installation, or if for any other reason SECO LARM determines that such
equipment is not operating properly as a result of causes other than defects in material and workmanship.
The sole obligation of SECO LARM, and the purchaser’s exclusive remedy, shall be limited to replacement or repair only, at
SECO LARM’s option. In no event shall SECO LARM be liable for any special, collateral, incidental, or consequential personal or
property damages of any kind to the purchaser or anyone else.
NOTICE
The information and specifications printed in this manual are current at the time of publication. However, the SECO LARM policy
is one of continual development and improvement. For this reason, SECO LARM reserves the right to change specifications
without notice. SECO LARM is also not responsible for misprints or typographical errors.
Copyright © 2009 SECO LARM U.S.A., Inc. All rights reserved. This material may not be reproduced or copied, in whole or in
part, without the written permission of SECO LARM.
U.S.A., Inc.
16842 Millikan Avenue, Irvine, CA 92606 Website: www.seco larm.com
Tel: [phone] Fax: [phone] E mail: sales@seco larm.com
mi EV 1645 N2BQ docx
PIKSR1
Troubleshooting
The screen is blank.
Check that the camera is powered up.
Check that the power supply’s polarity is
correct.
Check that the monitor is powered up.
Check that the video cable connecting the
camera to the monitor is connected properly.
The screen image is dim.
Clean the lens using a soft, clean cloth.
Check that the light source is adequate.
The screen image has poor
contrast.
Adjust the monitor’s contrast knob.
Change the position of the camera.
The screen image flickers. Change the position of the camera.
The screen image is
distorted.
Change the position of the camera.
The camera case is hot. Check that the correct power supply is in use.

ENFORCER WIDE ANGLE BULLET CAMERA
Installation:
1. Please read this manual carefully and keep it for
future reference.
2. Use the camera within given temperature and
electrical limits.
3. Do not mount the camera where it is exposed to
rain or other moisture, or in humid or dusty
places.
4. Do not point the camera at the sun. Heat could
damage the camera, even when not in use.
5. Do not mount the camera in areas exposed to
radiation, strong magnetic fields, or strong
electrical signals.*
6. Do not open or disassemble the camera.
There are no field-serviceable parts inside.
7. Do not drop the camera or subject it to strong
vibrations.
Note: Many video monitors produce strong
electromagnetic fields close to the display
CRT, especially when the monitor is turned on
or during de-Gaussing, which occurs
automatically with many monitors when the
monitor is turned on.
Before Starting:
1. Run a 12VDC power supply wire and a video
cable with a male BNC connector through the
wall to where the camera is to
be mounted.
2. Temporarily connect the camera to the power
supply. Do not cut DC jack or female BNC
connector as warranty will be voided. If
needed, use the included pigtail connector.
3. Temporarily connect the camera’s female BNC
connector to the video cable’s male
BNC connector.
4. While watching the monitor, hold the camera
against the wall or ceiling by hand where it is to
be mounted, then turn the camera until it is
certain that this mounting location is correct.
Use a pencil to mark the location of the six
screw holes in the mounting plate.
5. Disconnect the power supply and video cable.
6. Mount the mounting plate to the wall or ceiling
using the six included mounting screws. If the
wall is made of dry wall, brick, or similar
material, it may be necessary to use screw
anchors (not included).
7. Reconnect the power supply and video cable.
Turn the monitor on and make sure the camera
is sending the proper video signal.
8. Adjust the camera angle using the
adjustment nut.
9. Do a final test of the video camera and
monitor.
Overview:
Camera
Mounting holes
Adjustment nut
Important:
Do not cut DC jack or female BNC connector as warranty will be voided.
DC jack
Connect to video cable’s
male BNC connector
BNC connector
Pigtail connector
Mounting bracket
ENFORCER WIDE ANGLE BULLET CAMERA
Type
Wide-Angle Bullet Camera
CCD
1/3” Sony Super HAD II Color CCD
Resolution
Color: 550 TV Lines
B/W: 590 TV Lines
Pickup elements
768x494 pixels
Video output format
NTSC
Video output
1.0Vp-p composite video, 75Ω
Lens
2.2mm
Viewing angle
170°
Minimum illumination
0.1-lux at F/1.4
S/N ratio
>48dB
Scanning frequency
15.734KHz x 59.94Hz
Sync
Internal
Gamma correction
0.45
Gain control
Auto
IP rating
IP66
Power source
12VDC
Current draw
83mA
Operating temperature
14°~122° F (-10°~50° C)
Dimensions
31/2”x17/16”x17/16” (90x37x37 mm)
Weight
6-oz (160g)
Specifications
31/2” (90mm)
19/16” (40mm)
19/
16
”
(40mm)
17/
16
”
(37mm)
Parts List:
Dimensions:
1 x Manual
6 x Mounting screws
51/2” (140mm)
1 x Pigtail connector
1 x Camera
1 x Mounting bracket