ENFORCER EV-C2001-N3WQ User manual

700 TV Lines
1/3” CMOS Sensor
3.6mm Lens
3-Axis ball mount for wall or
ceiling mounting
Weatherproof (IP66)
Split-glass design to
eliminate IR reflection
Vandal-resistant design
NTSC Model
PAL Model
Features
EV-C2001-N3WQ
EV-C2001-P3WQ
700 TVL, White housing
Manual
Vandal Rollerball Cameras

ENFORCER Vandal Rollerball Cameras
2SECO-LARM U.S.A., Inc.
Model
EV-C2001-N3WQ
EV-C2001-P3WQ
Type
Vandal Rollerball Camera
CMOS
1/3” CMOS Sensor
Resolution
700 TV lines
Video output format
NTSC
PAL
Pickup elements
811x508
795x596
Scanning system
2:1 Interlace
Sync
Internal
Video output
1.0V p-p Composite output, 75Ω
Lens
3.6mm
IR Cut filter
Yes
# of IR LEDs
24 (850nm)
IR Range
Up to 50’ (15m)
Minimum
illumination
LEDs OFF
0.5 Lux
LEDs ON
0 Lux
Gamma correction
0.45
S/N Ratio
≥50dB
Shutter control
Auto Electric Shutter (AES), 1/60~1/100,000 s
Gain control
Auto
White balance
Auto
Operating voltage
12VDC
Current draw
LEDs OFF
95mA
LEDs ON
270mA
IP Rating
IP66
Operating temperature
14°~131° F (-10°~55° C)
Dimensions
33/4”x35/32” (95x80 mm)
Cable length
187/8” (480mm)
Weight
16-oz (450g)
Specifications:
Parts List:
1x Camera 1x Manual
4x Screws 4x Screw anchors
1x Mounting template
Dimensions:
33/4” (95mm)
35/32”
(80mm)

ENFORCER Vandal Rollerball Cameras
SECO-LARM U.S.A., Inc. 3SECO-LARM U.S.A., Inc. 33 3
1. Please read this manual carefully and keep it for
future reference.
2. Use the camera within the given temperature and
electricity limits.
3. Do not point the camera at the sun. Heat could damage
the camera, even when not in use.
4. Do not drop the camera or subject it to
strong vibrations.
5. Do not mount the camera in areas exposed to
radiation, strong magnetic fields, or strong
electrical signals.
Before Starting:
1. Run a 12VDC power supply wire and a video cable
with a male BNC connector through the wall to where
the camera is to be mounted.
2. Loosen the set screw with the included hex wrench
and remove the case from the base.
NOTE: The camera ball is NOT attached to the case
or the base. It sits loose inside the case. Therefore, be
very careful when removing the case from the base.
Do not drop the camera ball.
3. Mount the base to the wall using the four included
mounting screws. If the wall is made of dry wall, brick,
or similar material, it may be necessary to use the
included plastic screw anchors.
4. Run the camera’s BNC and power connectors through
the camera base, and connect to the video and power
wires that were run through the wall.
Installation:
5. Put the case over the camera ball onto the base. Be
careful to not drop the camera ball.
6. Holding the case loosely on the base, turn the camera
ball to the desired direction.
NOTE: Before securing installation, make sure to check
both the day and night images. Adjust the camera ball
so that there are no objects blocking or obscuring the
camera’s view.
7. Once the ball is pointing in the desired direction,
tighten the outer case ring to secure the camera in
its position.
8. Do a final test of the video camera and monitor.
Overview:
Camera ball
Case
Base
Screws
(Only 2 shown. Use all 4 when installing.)
Female BNC
connector
DC Jack

ENFORCER Vandal Rollerball Cameras
4SECO-LARM U.S.A., Inc.
IMPORTANT
Users and installers of this product are responsible for ensuring this product complies with all national, state, and local laws and
statutes related to monitoring and recording audio and video signals. SECO-LARM will not be held responsible for the use of this
product in violation of any current laws or statutes.
WARNING
Stop using the camera if you see a malfunction such as smoke or unusual heat, as it could cause fire or electric shock. Do not open
the case of this device, as there are no field-serviceable components inside.
FCC COMPLIANCE STATEMENT
Information to the user: This equipment has been tested and found to comply with the limits for a class B digital device, pursuant to
part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference when the
equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and,
if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to
correct the interference at his or her own expense.
WARRANTY: This SECO-LARM product is warranted against defects in material and workmanship while used in normal service
for a period of one (1) year from the date of sale to the original customer. SECO-LARM’s obligation is limited to the repair or
replacement of any defective part if the unit is returned, transportation prepaid, to SECO-LARM. This Warranty is void if damage is
caused by or attributed to acts of God, physical or electrical misuse or abuse, neglect, repair or alteration, improper or abnormal
usage, or faulty installation, or if for any other reason SECO-LARM determines that such equipment is not operating properly as a
result of causes other than defects in material and workmanship.
The sole obligation of SECO-LARM and the purchaser’s exclusive remedy, shall be limited to replacement or repair only, at
SECO-LARM’s option. In no event shall SECO-LARM be liable for any special, collateral, incidental, or consequential personal or
property damages of any kind to the purchaser or anyone else.
NOTICE
The information and specifications printed in this manual are current at the time of publication. However, the SECO-LARM policy is
one of continual development and improvement. For this reason, SECO-LARM reserves the right to change specifications without
notice. SECO-LARM is also not responsible for misprints or typographical errors.
Copyright © 2016 SECO-LARM U.S.A., Inc. All rights reserved. This material may not be reproduced or copied, in whole or in part,
without the written permission of SECO-LARM.
Troubleshooting:
The screen is black
Check that the camera is powered up
Check that the power supply’s polarity is correct
Check that the monitor is powered up
Check that the video cable connecting the camera to the
monitor is connected properly
The image is foggy or washed out at night
Check that there are no objects very close to the camera
Check that there are no highly reflective objects in the scene
The screen image is dim
Clean the lens using a soft, clean cloth
Check that the light source is adequate
The screen image has poor contrast
Adjust the monitor’s contrast knob
Change the position of the camera
The screen image flickers
Change the position of the camera
The screen image is distorted
Change the position of the camera
The camera case is hot
Check that the correct power supply is in use
IR LEDs do not turn on
Check that the correct power supply is in use
SECO-LARM®U.S.A., Inc.
16842 Millikan Avenue, Irvine, CA 92606
Website: www.seco-larm.com
PICCN2
Phone: [phone] | [phone]
Email: [e-mail]
MiEV-C2001-x3WQ_160630.docx