ENFORCER EV-2706-NFGQ User manual

Note: Productswith modelnumbers thatend with “Q” or thathave a round green “Q” sticker are RoHS compliant.
Varifocal Vandal Rollerball Cameras
Manual
NTSC Models
PAL Models
Features
EV-2706-NFGQ
EV-2706-PFGQ
700 TVL, Gray Housing
EV-2706-NFWQ
EV-2706-PFWQ
700 TVL, White Housing
EV-2726-NFGQ*
EV-2726-PFGQ*
700 TVL, 3D-DNR, 2D-DNR, WDR, Gray Housing
EV-2726-NFWQ*
EV-2726-PFWQ*
700 TVL, 3D-DNR, 2D-DNR, WDR, White Housing
*Includesbuilt-in OSD (On-ScreenDisplay) controller
3X Series – clear images in nearly any lighting situation
•
1
/
3
” Sony CCD
•2.8~12mm Lens
•3-Axis ball mount for wall or
ceiling mounting
•960H High resolution
•Weatherproof (IP65)
•Split-glass design to
eliminate IR reflection
•Vandal-resistant design

ENFORCER Varifocal Vandal Ball-Mount Dome Cameras
2SECO-LARM U.S.A., Inc.
Model NTSC
EV-2706-NFGQ
EV-2706-NFWQ
EV-2726-NFGQ
EV-2726-NFWQ
PAL
EV-2706-PFGQ
EV-2706-PFWQ
EV-2726-PFGQ
EV-2726-PFWQ
Type
Vandal Rollerball Camera
CCD
1/3” Sony Super HAD II
Resolution
700 TV lines
Pickup
elements
NTSC
976x494pixels
PAL
976x582pixels
3D-NR
No
Yes
WDR
No
Yes
OSD Control
No
Yes
960H*
Yes
Scanning system
2:1 Interlace
Sync
Internal
Video output
1Vp-p composite output, 75 ohms
Lens
2.8~12mm
# of IR LEDs
36 (850nm)
IR Range
Up to 100’ (30m)
Minimum
illumination
LEDs OFF
0.02 Lux
0.03 Lux
LEDs ON
0 Lux
Gamma correction
0.45
S/N Ratio
>52dB
DSS (Digital Slow Shutter)
N/A
256x
Shutter control
Auto Electric Shutter (AES), 1/60~1/100,000 s
Gain control
Auto
White balance
Auto
Operating voltage
12VDC ±10%
Current draw
LEDs OFF
100mA
150mA
LEDs ON
400mA
450mA
IP Rating
IP65
Operating temperature
-4°~131° F (-20°~55° C)
Dimensions
411/16”x37/8” (119x98 mm)
Cable length
34” (86cm)
Weight
1-lb, 13-oz (820g)
Dimensions:
Specifications:
Parts List:
1 x Camera
1 x Manual
4 x Screws
4 x Screw anchors
1 x DCPlug with
terminal block
1 x Small screwdriver
1 x Hex wrench
2 x Rubber plugs
Zoom
411/
16
” (119mm)
Focus
37/
8
”
(98mm)
Optional Mounting
Brackets (sold separately):
Wall Mount
Ceiling Mount
Conduit Box
Gray: EV-DWLGQ
White: EV-DWLWQ
Gray: EV-DCLGQ
White: EV-DCLWQ
Gray: EV-DSLGQ
White: EV-DSLWQ
Conduit Drop
Gray: EV-DDLGQ
White: EV-DDLWQ
*In order to take fulladvantageof 960H resolution, the camera must be used with a960HDVR.

ENFORCER Varifocal Vandal Ball-Mount Dome Cameras
SECO-LARM U.S.A., Inc. 3
1. Please read thismanual carefully and keep itfor
future reference.
2. Use the camera within the given temperature and
electricity limits.
3.
Do not point the camera at the sun. Heatcould damage
the camera,even when notin use.
4. Do notdrop the camera or subjectit to strong vibrations.
5. Do notmountthe camera in areasexposed to radiation,
strong magneticfields, or strong electrical signals.
Before Starting:
1.
Run a 12VDC powersupply wire and a video cable
with a male BNC connector through the wall to where
the camera isto be mounted.
2. Loosen the setscrewswith the included hex wrench
and remove the case from the base.
NOTE: The camera ballis NOTattached to the case
or the base. It sitsloose inside the case. Therefore,
be very carefulwhen removing the case from the
base.Do notdrop the camera ball.
3. Mountthe base to the wall using the four included
mounting screws. If the wall is made of dry wall,
brick, or similar material, it may be necessary to use
the includedplasticscrew anchors.
4. Run the camera’s BNC and power connectors
through the camera base, and connect to the video
and power wires thatwere run through the wall.
Installation:
5. Put the case over the camera ball onto the base. Be
careful to not drop the camera ball.
6. Holding the case loosely on the base, turn the camera
ball to the desired direction. Use the included small
screwdriver to adjust the zoom and focus of the camera
ball if needed, via the holes marked “ZOOM” and
“FOCUS” on the top ofthe camera ball.
NOTE:Before securing installation, make sure to check
both the day and nightimages. Adjust the camera ball so
that there are no objects blocking the camera’s view.
7. WDR Models Only: Use the OSD controllerjoystick to
adjustcamera settings (see the separateOSD manual).
8. Once the ballis pointing in the desired direction, tighten
the outer case ring to secure the camera in its position.
9. Do a final testof the video cameraand monitor.
10.
Insert the rubber plugs over the zoom and focus to prevent
tampering.
Overview:
Camera ball
Case
Base
Screws
(Only 2 shown. Use all 4 when installing.)
Female BNC
connector
DC Plug with
terminal block
DC Jack
Rubber Plug
Installation
OSD Controller
(WDR Models only)

ENFORCER Varifocal Vandal Ball-Mount Dome Cameras
4SECO-LARM U.S.A., Inc.
MiEV-27x6-NFxQ _1402.docx
PICSN4
IMPORTANT
Users and installers of this product are responsible for ensuring this product complies with all national, state, and local l
aws and
statutes related to monitoring and recording audio and video signals.
SECO-LARM willnot be held responsible for the use of this
product in violation of any current laws or statutes.
WARNING
Stop using the came
ra ifyou seea malfunction such as
smoke or unusual heat, as it could cause fire or electric shock. Do not open
the case of thi
s device, as there are no field-serviceable components inside.
FCC COMPLIANCE STATEMENT
Information to the user: This equipment hasbeen tested and found to comp
ly with the limits for a class B digital device, pursuant to
part 15 of the
FCC rules. These limits are designed to provide reasonable protectionagainst harmfulinterference when the
equipment is operated in a commercial environment. Thisequipment generates, uses, and can radiate radio frequency energy and,
if not installed an
d used in accordance with the instruction manual,maycauseharmful interference to radio communications.
Operation of this equipmentin a residential area is likely to cause harmful interference in which case the user will be requ
ired to
correct the inte
rference at his or her own expense.
WARRANTY: This SECO-LARMproduct is warranted against defects in material and workmanship while used in normalservice
for a period of three (3) years from the date of sale to the originalcustomer. SECO
-LARM’s obligation is limited to the repair or
replacement of any defective part if the unit is returned, transportation prepaid, to SECO
-LARM.
This Warranty is void if damage is caused byor attributed to acts of God, physical or electrical misuse or abuse, neglect, r
epair or
alteration, improper or abnormal usage, or faulty installation, or if for any other reason SECO
-
LARM determines that such equipment
is not operatingproperly as a result ofcauses other than defects in materialand workmanship.
The soleobligation
of SECO-LARM and the purchaser’s exclusive remedy, shall be limited to replacement or repaironly, at
SECO
-LARM’s option. In no event shall SECO-LARM be liable for any special, collateral, incidental, or consequential personalor
property damages of any
kind to the purchaser or anyone else.
NOTICE
The information and specifications printed in this manual are currentat the time of publication. However, the SECO
-LARM policy is
one of continual development and improvement. For this reason, SECO
-LARMreserves the rightto change specifications without
notice. SECO
-LARM is also not responsiblefor misprints or typographical errors.
Copyright © 20
14 SECO-
LARM U.S.A., Inc. All rights reserved. This material may not be reproduced or copied, in whole or in part,
without the
written permission of SECO-LARM.
SECO-LARM
U.S.A., Inc.
16842 MillikanAvenue, Irvine, CA 92606
Tel: 800
-662-0800 / 949-261-2999
Website: www.seco-larm.com
E
-mail: [e-mail]
Troubleshooting:
The screen isblack
•Check that the camera is powered up
•Check that the power supply’s polarity is correct
•Check that the monitor is powered up
•Check that the video cable connecting the camera to the
monitor is connected properly
The image isfoggy orwashed outat night •Check that there are no objects veryclose to the camera
•Check that there are no highly reflective objects in the scene
The screen image is dim •Clean the lens using a soft,clean cloth
•Check that the light source is adequate
The screen image haspoorcontrast •Adjust the monitor’s contrast knob
•Change the position of the camera
The screen image flickers •Change the position of the camera
The screen image is distorted •Change theposition of the camera
The camera case ishot •Check that the correct power supply is in use
IR LEDs donot turn on •Check that the correct power supply is in use