ENFORCER E-961-S50TB User manual

E-961-S50TB
Miniature Single Photobeam
Manual
Small size for a less conspicuous installation
Simple to install
Built-in AGC control to filter out lighting
disturbances
Signal strength indicator for easier alignment
LED indicators for power, signal strength,
and alarm
Weatherproof for outdoor as well as indoor
use (IP65)
Mounting hardware included

ENFORCER Miniature Single Photobeam
2SECO-LARM U.S.A., Inc.
Front
Overview:
Front Cover Removed
ENFORCER ®
115/16" (48mm)
3" (76mm)
Wiring
Opening
Mounting
Holes
Rear
Alarm Indicator LED
Signal Strength LED
Power LED
Wire Terminals
Transmitter
Receiver
NC/NO Selector
Side
13/16" (30mm)
1x
Transmitter
6x
Screws
1x
Manual
1x
Receiver
6x
Plastic wall anchors
Introduction:
The E-961-S50TB is a simple, easy-to-use, and easy-to-install single-beam infrared motion
sensor. The device easily installs almost anywhere to provide an invisible beam that, when broken,
sends a signal to activate a light, beeper, or other device. This makes the device perfect for use as
part of an access control system, a door or window monitor, a retail store customer alert, or many
other places where the user needs to know that someone has entered a specific room or building
or other protected area. The E-961-S50TB is weather-proof, and comes with a built-in AGC control
circuit that helps to filter out possible disturbance caused by local lighting conditions.
Specifications:
Parts List:
Number of beam channels
Single infrared beam
Number of beam frequencies
1
Sensor range
3~50ft (1~15m)
Infrared LED wavelength
940nm
LED beam spread angle
Approximately ±10°
Interrupt speed*
50ms
Input power
10~24VDC
Current draw
(max)
Transmitter
15mA@12VDC
Receiver
30mA@12VDC
Relay output
NO/NC relay (set by jumper, default is N.C.) 0.5A@30VAC/VDC
LED (Transmitter)
Green - Indicates connected to power
LEDs (Receiver)
Power (Green)
Indicates connected to power
Signal (Yellow)
Indicates receiver's signal is weak or beam is broken
Alarm (Red)
Indicates transmitter and receiver are not aligned or beam is broken
IP rating
IP65
Operating Temperature
-13~131°F (-25~55°C) maximum humidity 95%
Dimensions
3"x115/16"x13/16" (76x48x30 mm)
Weight
1.2-oz (34g)
*This is the minimum time interval for breaking the beam which will trigger the output.

ENFORCER Miniature Single Photobeam
SECO-LARM U.S.A., Inc. 3
V- V+
Wiring Diagram:
Power Supply
10~24VDC
Transmitter
–+
V- V+ COM NC/NO
Alarm or other
Equipment
Receiver
NOTE: Do not mount the E-961-S50TB where it is exposed to direct sunlight to prevent damage to
the sensor.
NOTE: For best operation, there should be a minimum of 40 inches (1 meter) between the
transmitter and receiver.
1. Find a location where the transmitter and receiver can be installed facing each other.
2. Ideally, mount the E-961-S50TB at least 8" (20 cm) above the floor. However, the actual
mounting height will depend on the application.
3. Test the E-961-S50TB before mounting. Connect power to the transmitter and receiver, and
hold them in the desired location by hand. Break the beam between them by walking through
or slowly waving a hand through the beam. Adjust the location until the device operates
properly.
4. Disconnect power.
5. With a pencil, lightly trace around the transmitter and receiver on the wall to show where they
will be mounted.
6. Take the covers off the transmitter and receiver. Hold the bases against the wall in the areas
traced, then use a pencil to mark the three holes in each base for mounting screws.
a. Wood or metal wall: Use a drill bit to drill a starter hole for each of the three mounting
screw holes in each base. Then screw the mounting screws into the three holes.
b. Dry wall: Use a drill bit to drill a hole just barely large enough to insert the plastic wall
anchors. Then screw the mounting screws through the base into the plastic wall anchors.
7. Ensure that the NO/NC jumper switch is correct for the device to be activated (default is N.C.).
8. Reconnect power, and connect the appropriate wires for the device to be activated to the
receiver wire terminals.
9. Replace the covers and then re-test the E-961-S50TB.
Sample Installation:

ENFORCER Miniature Single Photobeam
4SECO-LARM U.S.A., Inc.
Troubleshooting:
Sensor does not detect the object
Object may have a reflective surface which confuses the
sensor. Try changing the angle of the sensor
Green power LED does not turn on
Ensure that the power is connected
Yellow LED or Red LED does not turn off
Clean the transmitter and receiver sensors with a damp
(not wet) cloth
Readjust the alignment of the transmitter and receiver
Red LED lights when object is detected, but
the output device is not activated
Check the wiring between the receiver and the output
device for continuity
®
PICAN1
Mi_E-961-S50TB_151104.docx
Also Available from SECO-LARM®:
Quad Photobeam Detectors
Twin Photobeam Detectors
Long-Range Barrier Sensors
4 Models available –up to
660ft (200m) range
12~24 VAC/VDC
Weatherproof
4 Models available –up to
390ft (120m) range
12~30 VAC/VDC
Weatherproof
2, 4, 6, or 8 Beams available –
up to 393ft (120m) range
Multi-frequency
Weatherproof
Reflective Photobeam Sensor
Hooded Reflective Photobeam
Sensor
Flush-Mount Photobeam
Sensors
Available with 45ft (14m) or
35ft (11m) range
Weatherproof
Available with 50ft (15m) or
33ft (10m) range
Polarized version available
Weatherproof
Available with reflective beam
16ft (5m) or through beam and
33ft (10m) range
Adjustable alignment angle
IMPORTANT: Users and installers of this product are responsible for ensuring this product complies with all national,
state, and local laws and statutes related to monitoring and recording audio and video signals. SECO-LARM will not be
held responsible for the use of this product in violation of any current laws or statutes.
SECO-LARM®U.S.A., Inc.
16842 Millikan Avenue, Irvine, CA 92606
Website: www.seco-larm.com
Phone: [phone] | [phone]
Email: [e-mail]
NOTICE: The SECO-LARM policy is one of continual development and improvement. For that reason, SECO-LARM
reserves the right to change specifications without notice. SECO-LARM is also not responsible for misprints.
Copyright © 2015 SECO-LARM U.S.A., Inc. All rights reserved. This material may not be reproduced or copied, in whole or
in part, without the written permission of SECO-LARM.
WARRANTY: This SECO-LARM product is warranted against defects in material and workmanship while used in normal
service for one (1) year from the date of sale to the original customer. SECO-LARM’s obligation is limited to the repair or
replacement of any defective part if the unit is returned, transportation prepaid, to SECO-LARM. This Warranty is void if
damage is caused by or attributed to acts of God, physical or electrical misuse or abuse, neglect, repair or alteration,
improper or abnormal usage, or faulty installation, or if for any other reason SECO-LARM determines that such equipment
is not operating properly as a result of causes other than defects in material and workmanship. The sole obligation of
SECO-LARM and the purchaser’s exclusive remedy, shall be limited to the replacement or repair only, at SECO-LARM’s
option. In no event shall SECO-LARM be liable for any special, collateral, incidental, or consequential personal or property
damage of any kind to the purchaser or anyone else.