ENGO CONTROLS DOOR EDOORZB User manual
Quick Guide
Explanation for LED indicator
Installation of the door sensor in the app
STEP 1 DOWNLOAD ENGO SMART APP
Download the ENGO Smart app from Google Play or Apple App Store and install
it on your smartphone.
Make sure your router is within range of your smartphone. Make sure you are
connected to the Internet.This will reduce the pairing time of the device.
EDOORZB is a battery-operated magnetic sensor, compatible with the ZigBee 3.0
standard. A change in the state of the device automatically sends a signal to a
ZigBee Internet gateway (Engo EGATEZB). It can be used to create rules for the
operation of home appliances (scenes) and where you need information about
the opening or closing of doors, windows, garage doors, etc.
Using the Engo Smart app, it is possible to create a relationship between the
window opening sensor and the room temperature thermostat (e.g. if the
window is opened, the heating or air conditioning is turned o). The opening is
detected by the distance between the sensor and the magnet.
The product is designed for indoor use only.
The sensor must be combined with a universal ZigBee 3.0 gateway (Engo EGATEZB).
Ver. 1
Date of issue: IX 2022
Technical Informations
EDOORZB installation
Introduction
Power supply CR2450
Communication ZigBee 3.0, 2.4GHz
Dimensions 72x42x16 mm
Product Compliance
This product complies with the following EU Directives: 2014/53/EU, 2011/65/EU
LED INDICATOR
STATUS
DEVICE
STATUS DESCRIPTION
The Green LED
ashes
The device is in
pairing mode
This mode is triggered by
long button press
(reset button hold for 8 sec.).
Single ash of the
Green LED
the device sends
information to the app
Device is properly connected to
the network and app can receive
information from sensor.
LED indicates current status
of the device
www.engocontrols.com
Remove the battery cover. Remove protective lm of the sensor.
Stick the sensor and magnet to the frame and sash of the door / window,
no more than 5mm from each other.
1
3
2
Distributor:
QL CONTROLS Sp z o.o. Sp. k.
43-262 Kobielice
4 Rolna St.
Poland
Producer:
Engo Controls S.C.
43-200 Pszczyna
3E Górnośląska St.
Poland
EDOORZB | ZigBee Door/Window Sensor
DOOR
STEP 3 - CONNECT THE SENSOR TO APP
To reset the device to factory settings, hold down the RESET button located at the
bottom of the device (see picture) for approx. 8 seconds (use the PIN included
in the set). The sensor will be removed from the ZigBee network and gateway
memory. Device is ready to re-add it again.
Click„Register”to create
new account.
Enter the verication
code received in the email.
Remember that you
only have 60 seconds to
enter the code!
Then set the login
password.
Enter your e-mail
address to which the
verication code will
be sent.
After nding the device, go„Done”.
Window/door sensor is ready to work.
After successful pairing the
device will appear
on gateway’s list of devices.
Click on it to view the interface.
Enter the gateway interface.
Select„Zigbee devices list”
and go„ Add devices”.
Using the PIN included, press and
hold the RESET button for 8 seconds
until the green LED starts ashing.
The pairing mode is enabled.
Name the device
and click„Done”.
Then wait until the application
nds the sensor.
Reset the sensor
STEP 2 - REGISTER THE NEW ACCOUNT
To register a new account, please follow the steps below: After installing the app and creating an account, install the ZigBee Gateway
in accordance with the instructions attached to it, and then:
1
5
7
3
1
3
2
6
8
4
2
3
4
