ELRO HA2000PP User manual

D.A.S.P. PET IMMUNE PIR Motion Sensor (HA2000PP)
The PIR Pet-Immune Motion Sensor ensures the excellent catch performance of its original purpose in the security sense and in addition,
eliminates unnecessary false alarms caused by those pets. HA2000PP is designed to detect movements within an assigned area and signals
the Control Panel to activate the alarm if an intruder crosses its’ path of detection but will not detect a dog up to 27 kilos, 10 cats, or numerous
rodents.
The PIR consists of a two-part design made up of a cover and a base. The cover contains all the electronics and optics and the base provides a
means of fixing. The base has knockouts to allow mounting on either a flat surface or in a corner situation with a triangular bracket for corner
mounting.
Provision for a tamper switch that will be activated when the cover is detached from the base prevents unauthorized access and removal from
the mounting surface. The PIR can also alert you to signal communication problems and low battery situations.
The PIR is designed to give a typical detection range of 12 meters when mounted at 2 meters above ground.

 I Id de en nt ti if fy yi in ng g t th he e p pa ar rt ts s. .
1. Test Button LED indicator
It is the test button and also doubles as the LED indicator. The test button is used for testing the
radio performance and for learning purpose. The LED indicator is used to indicate the status of
system.
2. Tamper Switch
The Tamper switch protects the enclosure from being opened.
3. Battery Insulator
4. Corner mounting bracket

 S Su up pe er rv vi is si io on n F Fu un nc ct ti io on n
When the PIR is in Normal operation mode it will conduct a Self-test randomly by transmit a
supervisory signal once between every 20 minutes to 50 minutes
If the Control Panel doesn’t receive the Supervisory signals transmitted from a certain PIR, an
“Out-Of-Order” fault message will be generated.

 S Sl le ee ep p T Ti im me er r
The PIR has a “sleep time” of approximately 1 minute to conserve power. After transmitting a detected
movement, the PIR will not retransmit for 1 minute; any further movement detected during this sleep
period will extend the sleep time by another minute. In this way continuous movement in front of a
PIR will not unduly exhaust the battery.

 T Te es st t m mo od de e
The PIR can be put into Test mode by pressing the Test Button LED on the front cover. In Test mode, it
will disable the sleep timer and will enable the LED indicator to flash every time a movement is
detected. Each time press the Test Button, the PIR will transmit a test signal to the Control Panel for
radio range test and enter the test mode for 3 mins. It will exit Test Mode automatically after 3 mins
and returns to normal mode.

 L LE ED D I In nd di ic ca at to or r
In Normal operation mode, the LED Indicator will not light except in the following situations:
When the PIR is in low battery condition, every time it transmits a detected movement, the LED will flash for about 2 seconds.
When the cover is opened and the tamper switch is violated, the LED will light up for 2 sec. to indicate it is transmitting the “Tamper”
signal.
When the Tamper condition persists, every time it transmits a detected movement, the LED will light up.
However, if the PIR is in Test mode, the LED will light up every time a movement is detected.

 B Ba at tt te er ry y
The PIR uses one 3.6 V Lithium battery as its power source. The PIR will have a typical battery life of 5 years at an average of 20
activations a day.
Low battery detection operates at a threshold of 3.2V+/-2.4% where the PIR has enough reserve energy to typically operate for 1 month
before complete exhaustion. A low battery signal will be sent to the Control Panel along with regular signal transmissions for the Control
Panel to display the status accordingly.
For each installation, the battery is installed in by the factory before shipment with an Insulator inserted.

 G Ge et tt ti in ng g S St ta ar rt te ed d
Pull out the battery Insulator steadily.
The LED indicator steadily flashes for 30 seconds. (The PIR is warming up). During the warming period, the PIR will not be
activated. It is recommended that you stay away from the detection area during this time. After the warming period is over, the light
will turn off and the PIR will be ready for operation.
Put the Control Panel into “Device +/-“ menu and then select “Add Device” menu.
Press the test buttons on the front cover.
Refer to the operation manual of your control panel under the section of “Device +/-“ to complete the learn-in process.
After the PIR is learnt-in, put the Control Panel into “Walk Test” mode, hold the PIR in the desired location, and press the Test button
to confirm this location is within signal range of the Control Panel.
When you are satisfied that the PIR work in the chosen location, you can proceed with installation.

 L Li im mi it ta at ti io on ns s
The PIR is designed to give a typical detection range of 12 meters when mounted at 2 meters above ground. When mounted at 2.3 meters
above ground, it gives a typical PET IMMUNE range of 7 meters. As the PIR is higher from above ground, it gives a further PET IMMUNE
range. To take full advantage of HA2000PP, the following guidelines should be considered:

Do not position a PIR to look directly at a door protected by a Door Contact, this could cause the Door Contact and PIR radio signals
to be transmitted at the same instant when entering, cancelling each other out.
Do not install the PIR completely exposed to direct sunlight.
Avoid installing the PIR in areas where devices may cause rapid change of temperature in the detection area, i.e. air conditioner,
heaters, etc.
Avoid large obstacles in the detection area.
Not pointing directly at sources of heat e.g. Fires or boilers, and not above radiators.
Avoid moving objects in the detection area i.e. curtain, wall hanging etc.
But It is recommended to install the PIR in the following locations:
In a position such that an intruder would normally move across the PIR’s field of
view.
Mount the detector at 2.1 M ~ 2.4 M high for best performance:
<
<I IM MP PO OR RT TA AN NT T N NO OT TE E> >
 For the most desired performance of HA2000PP, remember to adjust the height of
HA2000PP mounting site respectively to the height of the tallest animal in the house.
As the taller than average dogs require the HA2000PP to be mounted higher for the
Pet Immunity purpose.
 When deciding on the height of the HA2000PP mounting site, remember to take the
possible blind spot into consideration. The blind spot underneath the HA2000PP
enlarges proportionally to the height of the HA2000PP mounting site.
Mount where the animals cannot come to the detection area by climbing on furniture or other objects.
Don’t aim the detector at stairways the animals can climb on.
In a corner to give the widest view.
Where its field of view will not be obstructed e.g. by curtains, ornaments etc.

 M Mo ou un nt ti in ng g M Me et th ho od d
The PIR is designed to be mounted on either a flat surface or in a corner situation with fixing screws and plugs provided.
The base has knockouts, where the plastic is thinner, for mounting purpose. Four knockouts are for surface fixing and four knockouts
are for corner fixing as shown in the picture.
For corner mounting, at user’s own dicretion, an optional triangular bracket is
provided to add Back Tamper Protection. Mount the triangular bracket on he
wall first with the two pointing sticks on top facing you. Then, you can just fit the
PIR onto the hooks of the triangular bracket or screw the PIR onto it.

 S Su ur rf fa ac ce e m mo ou un nt ti in ng g: :
Step1. Remove the fixing screw and cover assembly.
Step 2. Break through the appropriate knockouts on the base.
Step 3. Using the holes as a template, drill holes in the surface.
Step 4. Insert the wall plugs if fixing it into plaster or brick.
Step 5. Screw the base into the wall plugs.
Step 6. Screw the cover back onto its base.

 C Co or rn ne er r m mo ou un nt ti in ng g: :
Step 1. Break through the two knockouts on the triangular bracket.
Step 2. Using the two holes as a template, drill holes in the surface of the corner
Step 3. Insert the wall plugs
Step 4. Screw the triangular bracket into the wall plugs with the two pointing sticks on
top facing you.
Step 5. Fit the PIR onto the hooks of the triangular bracket
Step 6. If necessary, open the PIR by removing the fixing screw and cover assembly
Step 7. Break through the appropriate corner fixing knockouts.
Step 8. Using the corner fixing knockouts as a template, drill holes in the surface in the corner again
Step 9. Insert the wall plugs if fixing it into plaster or brick.
Step 10. Screw the base into the wall plugs
Step 11. Screw the cover back onto its base

 S Sp pe ec ci if fi ic ca at ti io on ns s: :
Common Technical Specification:
Radio frequency: 868.6375MHz +-2.5ppm
Modulation/ Demodulation: Narrow band FM @ 15KHz
bandwidth with VCTCXO (Temperature compensated
Crystal)
Sensitivity: >105dbm @S/N +20db
Transmission power: E.I.R.P. -8dbm +-3db
Operation range: 300 meters in open space
Code combinations: 16 777 216 codes
Temperature range:-20°C +45°C
Humidity: up to 90%
PIR Detector HA2000PP
Analysis by ConversionA/N (MSLT), temperature
compensation Protection High Frequencies (magnetic
and radio interferences)
Detection range: 90°over 12 meters, 19 sectors with 9
on same line
Supervision: Random 30 min to 50 min
LED light and button: Default & Test Mode.
Transmitted signals: Opening, Closing, Weak battery,
Tamper, Tamper closed, Supervision and Test Mode.
White lens reflecting up à 6000 lux (solar rays, vehicle
beams…)
Double Tamper protection : rear mount + cover
Battery life: Over 3 years assuming 50 transmissions /
day. Roughly 5 years under normal use. 1 month after
weak battery signal. Lithium battery AA 3.6V 2400mAH
Weak battery detection
Dimensions: 93mm (L)*64mm (W)*42mm (H)


 G Gu ua ar ra an nt ty y
This product is guarantee 4 years except the
batteries. The first year is by standard exchange.
The 3 years left, the guarantee is for parts and
labours.
Please contact, the technical line, following your country, to
confirm the default and the guarantee process.
France:
Eden: 0825 560 650
Web site: www.eden.fr
Holland:
Elro: 0900 208 8888
Web site: www.elro-nl.com
Belgium:
Dutch speaking
Elro: 070 2330031
French Speaking
Eden: 0033 825 560 650
Germany:
Elro: 0049 17755 24123
England:
Byron: 0845 230 1231
Website: www.chbyron.com