Enso flex EZZ FE1200 User manual

FE1200 Wireless Adjustable Base
OWNER’S MANUAL
Installation & Operation
Patent Pending
2-Year Parts and Labor on entire base
Warranty.
Serial No.

Safety & Warranty Warnings 1-5
Parts List 6
FE1200 Electronics Quick Reference Guide 7-8
Installaon Guide 9-10
FE1200 Remote Control Instrucons 11-12
Seng Programmable Posions and Pairing Remote 13-15
Emergency Baery Backup 16-17
Synchronizing Two Bases 17-18
Headboard Bracket Installaon Guide 19
Troubleshoong 20-22
CONTENTS

Safety & Warranty Warnings
Aenon: Read the following informaon before using this product . Failure to use a surge protecon device could compromise safety or
cause product malfuncon and could void the electrical poron of your warranty.
Electrical surges are by far the biggest cause of problems with electrical circuits.
In order to help protect your investment in case of a power surge or outage, use an electrical surge protecon device (not included).
WARRANTY WARNING!
Do not open or tamper with the transformer, control box, motors, or remote control (with the excepon of baery compartments). The
product warranty will be void if these components are tampered with.
SMALL CHILDREN AND PETS:
Immediately dispose of all packing materials as they can smother small children and pets. Do not allow any persons or pets under the bed.
Children, convalescents and disabled person should not operate the bed without adult supervision.
HOSPITAL OR CONVALESCENT USE DISCLAIMER:
Adjustable beds are designed and engineered for a life style of in-home comfort and are not intended for hospital use or for a bed-ridden
paent on an extended recovery. Adjustable beds are not equipped with bars to help paents get safely in and out of bed and are not
intended to be used around tent type oxygen therapy or explosive gases.
1-22

PACEMAKER WARNING:
The massage units in this bed produce mechanical vibraons that this warranty; (d) to damage to maresses, fabric, cables, electrical cords
or items supplied by dealers. Contact the dealer for warranty informaon on these items; (e) if there has been any modificaon of the
adjustable bed without prior wrien consent by nisco; (f) to costs for unnecessary service calls, including costs for in-home service calls
solely for the purpose of educaon the consumer about the adjustable bed or finding an unsasfactory power connecon; (g) if the
recommended weight restricon is not followed (refer to the advisory secon of this manual), the warranty will be void. Repairs to or
replacement of an adjustable bed or its components under the terms of this limited warranty will apply to the original warranty period and
will not serve to extend such period. The decision to repair or to replace defecve parts under this warranty shall be made, or cause to be
made, by nisco at its opon and in its sole discreon. Repair or replacement shall be the sole remedy of the purchaser. There shall be no
liability on the part of nisco for any special, indirect, incidental, or consequenal damages or for any other damage, claim, or loss not
expressly covered by the terms of this warranty. This limited warranty does not include reimbursement for inconvenience, removal,
installaon, setup me, loss of use, shipping, or any other costs of expenses, nisco and/or its service technicians shall not be responsible for
moving furniture or any other items not aached to the adjustable bed in order to perform service on the adjustable bed. It is the sole
responsibility of the purchaser to provide adequate space and accessibility to the adjustable bed. In the event that the technician is unable
to perform service due to lack of accessibility, the service call will be billed to the purchaser and the service will have to be rescheduled.
nisco makes no other warranty expressed or implied, and all implied warranes of merchantability and fitness for a parcular purpose are
disclaimed by nisco and excluded from this agreement. Some states do not allow the exclusion or limitaon of incidental or consequenal
damages, so the above limitaon or exclusion may not apply to every purchaser. This warranty gives the purchaser specific legal rights, and
the purchaser may also have other rights, which may vary from state to state. This warranty is valid in all 50 states, Puerto Rico, and Canada.
2-22

NISCO CO., LTD (“nisco”) warrants this adjustable bed to the consumer who is the original purchaser (the “purchaser”), subject to the terms
and condions set forth herein. This warranty begins on the “warranty commencement date” which is the date of purchase for new unused
beds and the date of manufacture for beds that have been used as floor or display models.
1ST & 2ND YEAR FULL WARRANTY
For the 1st and 2nd year from the Warranty Commencement Date, your adjustable base is warranted against non-excluded defects in nisco’s
workmanship or materials. During the 1st and 2nd year from the Warranty Commencement Date, nisco will repair or replace (at no cost to
You) any defecve adjustable base part, and nisco will pay all authorized labor associated with the repair or replacement of any parts found
to be defecve. In the case where adjustable base needs to be replaced nisco does not cover or pay for any part of transportaon costs.
ADDITIONAL TERMS AND CONDITIONS
This warranty does not apply; (a) to any damage caused by the purchaser; (b) if there has been any repair or replacement of adjustable bed
parts by an unauthorized person; (c) if the adjustable bed has been mishandled (whether in transit or by other means), subjected to physical
or electrical abuse or misuse, or otherwise operated in any manner inconsistent with the operaon and maintenance procedures outlined in
the Owner’s Manual and may acvate a special sensor in your pacemaker that detects moon. This can fool the pacemaker into “thinking”
you are engaged in some sort of physical acvity and require a faster heart rate. You may experience a sensaon similar to when you are
exercising. Consult your physician for further informaon.
3-22

PRODUCT RATINGS:
The bed li motors are not designed for connuous use of more than 2 minutes in an 18 minutes period, or approximately 10% duty cycle.
Any aempt to circumvent or exceed this rang will shorten the life expectancy of the product and may void the warranty.
WEIGHT UNITS:
The limitaon for this adjustable bed is 850 lbs. The bed will structurally support these weights, provided weight is evenly distributed across
the head and foot secons. This product is not designed to support or li this amount in the head or foot secon alone. Exceeding this
weight restricon could damage the bed and/or cause injury and void the warranty. Enter or exit the bed in a flat posion and do not sit on
the head or foot secons while in the raised posion.
LIFTING AND LOWERING MECHANISMS AND MASSAGE UNITS:
It is normal for the raising and lowering feature on this bed to emit a minimal humming sound during operaon. The massage feature
creates a vibrang hum during operaon and the resonance will increase accordingly with a higher intensity motor seng.
LOCATION ENVIRONMENT:
The level of sound experienced in a room is directly related to the environment within that locaon. In a room with hardwood floors and the
massage units turned on, a vibrang noise can be noceable. To reduce the resonance, place a piece of carpet or rubber casters cups under
the legs. The rubber caster cups also prevent the bed sliding when located on smooth or hard surface flooring.
4-22

For customer service under this limited warranty please contact Nisco.
Toll free phone: [phone]
TO REDUCE THE RISK OF SHOCK, BURNS, FIRE OR INJURY:
Make sure the base is in a flat posion and the vibrang motors are turned off before unplugging the bed base from the power source.
Always unplug the base from the electrical outlet before cleaning or servicing the base . If the cord or plug is damaged, disconnue use of
the bed base. Contact a qualified service personnel for examinaon and repair.
FCC COMPLIANCE:
This device complies with part 15 of the FCC Rules for residenal use. Operaon is subject to the following two condions: (1) This device
may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause
undesired operaon.
Radio Frequency: 2.4 GHz
5-22

All electronics and components that need to be installed are located in boxes under the foundaon or
aached to the frame. Before discarding the packing materials, ensure that all the parts are accounted for.
Actual product appearance and
funconality may vary from photographs.
(2) 9-Volt Baeries
Socket and Crescent Wrench
Power Cord (1)
AAA Baeries (2)
A
Bed Legs & Boom Caps (6)
King/CK Bed Legs & Boom Caps (7)
B
Power Supply (1)
C
D
Remote Control (1)
E
Retainer Bar (1)
Aached to the bed frame
F
Parts List
6-22

FE1200 Electronics Quick Reference Guide
7-22
Control Box Foot Motor
Head Motor

Foot Motor
Power Cord
Pairing Buon Power Supply
Head Motor
8-22

Two people are required to set up the foundaon.
NOTE: To avoid damage to the foundaon, always open the
carton while the bed is in the flat posion.
1. Open the shipping box, cut the ribbon securing accessory
boxes & maress retainer bar, and put them aside.
Li the folded bed frame unit out of the shipping carton
carefully, and then put it on a flat floor.
2. To install all six legs (seven for king/CK size,see image A on
page 10) , thread the bolt of the leg to the nut on the
foundaon frame, and ghten by hand. DO NOT OVERTIGHTEN.
3. Uncoil the input power cord (connected to the control box’s
power port) and plug it into the power supply.
4. Uncoil the power cord and connect it to the power supply.
Installation Guide
9-22

Middle Leg on King/CK Size Only
Leg Posions
A
Head
Foot
6. Ensure that baeries are correctly installed.
5. Carefully flip the foundaon over onto its legs.
Important: Two people are required to move the foundaon.
Do not drag across the floor. Do not rest frame on its side;
excessive pressure may damage the legs.
7. Locate the maress retainer bar brackets.
Slide the le side of the maress retainer bar into the bracket.
Pull the retainer bar to the opposite bracket and secure the
right side.
10-22

FE1200 Remote Control Instructions
11-22
Lis and Lowers Head Lis and Lowers Foot
Flash Light on/off
Flat Buon
Memory Posions

12-22
ONE TOUCH BUTTONSADJUST
The HEAD arrows lift and lower
the head section of the foundation.
The FOOT arrows lift and lower
the foot section of the foundation.
One touch FLAT preset position.
One touch memorized position.

STEP 3
Setting Programmable Positions and Pairing Remote
SETTING PROGRAMMABLE POSITIONS
To adjust the saved posion, repeat steps 1 and 2 and the new posion will be saved.
STEP 1
Adjust the head and foot to your desired posion.
STEP 2
Press and hold the flat buon first, then press and
hold memory buon for 5 seconds unl you hear 2
beeps sound.
The wireless power bed has a programmable feature that allows you to save custom posions.
Please read all the instrucons below before seng your custom presets on the remote.
13-22

PAIRING REMOTE
STEP 1
Make sure the baeries work fine. Replace them when needed.
STEP 2
Plug the power cord to the power source.
The original remote that comes in the box is already paired to the foundaon. No further acon is required.
In the event that the remote is not paired with the foundaon, follow the steps below.
STEP 3
Press and hold head li and foot li simultaneously, then press and hold the buon on the cord of control
box for 3 seconds unl your hear 2 beeps sound, the remote is then paired.
Pairing Button
14-22

Emergency Battery Backup
Overview
Important: The backup baery is only to be used in case of a power outage. Baeries are not to be used for normal operaon of the bed. The
backup baery will not support repeated movement for an extended period of me.
Backup Baery Use:
Use two 9V baeries only (not included). If a power outage occurs, install the 9V baeries into the power supply to allow temporary power
to the base (see image A).
Installing Baeries:
Unplug the power cord from the outlet and remove the cover from the compartment on the underside of the power supply (see image B).
Place two 9V baeries inside, close the cover and plug the power cord back into the wall outlet. The backup baery will not support
repeated movement for extended periods of me. Aer power is restored, unplug power cord, remove the baeries, then plug the power
cord back into the wall for normal use.
15-22

16-22

Synchronizing Two Bases
17-22
STEP 1
Plug A and B bases to power source.
STEP 2
Make sure remote A was already paired to Base A and Remote B
was paired to Base B. If not, please pair them by following the
pairing remote instrucons on page 11-12.
Remote A Remote B
Pair remote A to Base B, then base A and base B can be
simultaneous operated by Remote A.
STEP 3
Remote A
Pairing
Base B
Base A
Base B
Base A