ENSOTECH SWAVE-E2 User manual

ENSOTECH LIMITED
www.ensotech.ltd
Swave-E2 / Swave-W Electronic Speed Controller
User Manual v1.0
In this document mentioned and included how to use the product / cautions / maintains / warranty /
disclaimer / terms & conditions
Introduction
Thank you for choosing Swave E2 & W Electronic Speed Controller, its novel technology provides smoothest and
ultra-efficient performance. Please, read this manual and terms and conditions carefully before installing your new
Swave E electronic speed controller. All Ensotech products was sealed with a label shows the hyper link to download
this manual.
Once the seal is broken and the package opened, the acceptance of the below
Terms and conditions : https://shop.ensotech.ltd/index.php?route=information/information&information_id=5
Warranty: https://shop.ensotech.ltd/index.php?route=information/information&information_id=14
If you have any queries and uncertain please do not open the package, consults with your seller or Ensotech.
Registered Trademark
ENSOTECH is registered trademarks of Ensotech Limited.
All other brands mentioned in this guide are protected by copyright being the property of their respective owners.
Safety Precautions and Maintenance
-Not for children under 14 years old. This is not a toy.
-Swave E needs NO external capacitors or any other rework.
-Use Ensotech certified sensored motor with Ensotech Brushless ESC for best performance and protection.
-Using a not approved sensored motor may result in excessive current draw due to advance motor timing and may
cause severe ESC damage that will not be covered by product's warranty!
-Swave E ESC is a high end racing product that offers many customized parameters. If you are not certain about any
of the settings, contact your dealer for assistant or contact us.
-Do not overload motor due to incorrect/high gear ratios. Make sure the gear mesh is set properly. If the mesh is too
loose it can cause motor and ESC overheat which will damage the ESC and motor.
-Do not allow motor, ESC and battery in contact with water or other fluids, this could cause internal shortcut and
damage.
-Disconnect and remove the battery when ESC is not used.
-To prevent the runaway of your R/C car model, do not connect battery to the ESC or switch on the ESC without
switching-on the transmitter.
-Plug-in and solder connections may loose due to vibrations or collisions. Please, ensure secure connections,
otherwise you may experience a short-circuit which will damage the device.
-Always switch off the ESC before connect and disconnect programming cable.

HARDWARE IS YOUR EXCELLENCE
WWW.ENSOTECH.LTD
Unit F, 6 Floor, Cheung Hing Shing Centre, No.23, Sha Tsui Road, Tsuen Wan,
New Territories, Hong Kong
2
Motor Compliance:
The Swave series of electronic speed controllers (ESC) uses a very unique, groundbreaking and revolutionary
patented technology, which only Ensotech masters. This precision technology requires very careful and specific
engineering process for sensored motors and demand the use of high-quality motor components (i.e. sensor, PCB,
stator, winding etc..) coupled with the accuracy of the motor’s build and timing ‘tuning’. Ensotech certified motors meet
all the manufacturing and quality control criteria imposed by Ensotech, and would guarantee the best performance of
your Swave series ESC. The use of non-Ensotech certified motors, shall immediately void the Ensotech
warranty.
Ensotech does not impose any restrictions on the use of sensorless 1528 & 1628 sized brushless motor with the
Swave series ESC.
Ensotech certified sensored motor list is HERE
PARTS INCLUDED IN THE PACKAGE
1* Swave-E2 / Swave-W Electronic Speed Controller
1* Receiver Cable (JST)
1* Receiver Cable (JR)
1* Motor Sensor Cable (product code: CABLE06)
Swave E2
Swave W
Optional Parts and what you will needed
UARTLINK-II programming Cable via android device
Bluetooth wireless connector to program your esc via mobile device (2018 December)
Battery Power Connector JST-PH OR recommend MR-30 male and MR-30 female
Motor Cables

HARDWARE IS YOUR EXCELLENCE
WWW.ENSOTECH.LTD
Unit F, 6 Floor, Cheung Hing Shing Centre, No.23, Sha Tsui Road, Tsuen Wan,
New Territories, Hong Kong
3
Features
-"Blinky-mode" provides a fair racing environment between racers. (Shows that all timing advance switched to zero)
-Stunning size and weight
-Easy-to-use programming
-Firmware update available
-Programmed by Android system, via Ensotech - UARTLINK-II (optional) (Product Code: UARTLK-II)
-Programmed by Android system via (optional) wireless Bluetooth adaptor "EnsoBlueth" (December 2018), a
fully functional connection to change settings, update firmware and show telemetry.
-Professional set of customized parameters for the difficult race track
-ESC protection in case of one or two Hall sensor wire break
-Automatic recognition of Hall sensor’s position even when wire connections are swapped
-Settings configurations export and import. (You can save and load configuration or share out)
-Aluminum body for better heating dissipation
Specification: Swave-E2
Swave-E2
Dimensions (mm):
21.8(L)*12.7(W)*7.8(H)
Weight:
4g
Supply Voltage:
2s LiPo / 2s LiOn
Const./Brust Current (A):
14/20A (under 90 degree Celsius)
Sensor input:
1 (5 pins)
Programming input:
1
Receiver input:
1
Support motor type (Sensored):
Slotless 15mm Brushless DC up to 5500kv
Support motor type (Sensorless):
Slotless 15mm/16mm Brushless DC
BEC Output:
1.0A (max.)
Android App Version
1.4.3 or later
Specification: Swave-W
Swave-W
Dimensions (mm):
25.1(L)*13.2(W)*7.86(H)
Weight:
4g
Supply Voltage:
2s LiPo / 2s LiOn
Const./Brust Current (A):
20/30A (under 90 degree Celsius)
Sensor input:
1 (5 pins)
Programming input:
1
Receiver input:
1
Support motor type (Sensored):
Slotless 15mm Brushless DC up to 8000kv
Support motor type (Sensorless):
Slotless 15mm/16mm Brushless DC
BEC Output:
1.5A (max.)
Android App Version
1.4.3 or later

HARDWARE IS YOUR EXCELLENCE
WWW.ENSOTECH.LTD
Unit F, 6 Floor, Cheung Hing Shing Centre, No.23, Sha Tsui Road, Tsuen Wan,
New Territories, Hong Kong
4
SOLDERING THE CABLE
-DO NOT OVERHEAT SOLDER TABS, consider of small size electronics components are very sensitive and easy to
damage by over heat, Ensotech recommend it should not soldering each connection point more than 1 second with
maximum of 300 degree Celsius. Beside, please make sure the cable and soldering material are well covered the
conductive surfaces as possible, and fully isolated from any other conductive surfaces.
If weak connecting of conductive surfaces cause the ESC failure, it is not under warranty.
Better soldering work gives advantage of decrease the electronic resistance, the calibration beep sound become
launder and the ESC will perform better performance.
HOOKUP INSTRUCTION
Connect “sensor cable” – a cable between ESC and Ensotech certified sensored motors.
Connect “receiver cable” – a cable between ESC and receiver.We have included two different types of cable plug (JR
& JST) for different receivers.
The motor should be well and properly soldered to the ESC. This is very valuable for getting full performance from the
system and reduce heating.
A B C
+ -
Hall
Th rot tle
Android
Uart
Link
Swave E2/W
Connection
Diagram
Battery
B
A
C
Receiver
Smartphone
MTR

HARDWARE IS YOUR EXCELLENCE
WWW.ENSOTECH.LTD
Unit F, 6 Floor, Cheung Hing Shing Centre, No.23, Sha Tsui Road, Tsuen Wan,
New Territories, Hong Kong
5
THROTTLE CALIBRATION
STEP 1
Turn on your transmitter and connect a fully charged battery to the ESC.
STEP 2
Pull the trigger for full BRAKE/REVERSE and HOLD it in this position.
STEP 3
Turn on the ESC and wait for one short beep – switch-on beep (motor must be connected to the ESC, or there will be
no sounds). After that wait for another beep – calibration beep. (it will be in a second). Do not release the trigger
before calibration beep.
** Beep sound came from the motor movement, there will be no sound without motor.
Full
Reverse
Neutral
point
BEEP
STEP 4
Pull the trigger to full throttle and wait for TWO short beeps
Full
Throttle
Neutral
point
BEEP
BEEP
STEP 5
Release the trigger to neutral position and wait for THREE short beeps
Full
Throttle
Neutral
point
BEEP
BEEP
BEEP
Calibration finish!
PLEASE NOTE THAT some advanced transmitters have radio channel encoding features. In most cases they use
SSL/SSR open channel encrypting protocol (for details read transmitter’s manual) that requires some time to establish
connection between itself and receiver. Swave ESC will be wait for calibration during 2 seconds. If your radio system
requires a comparable time for establishing connection in encrypted mode you should switch this mode off! In other
case some difficulties with calibration may occurs. If you are not certain about the compatibility with your radio system,
please do not open the package. Consult with your seller.
Without properly done calibration the ESC can be damaged. Ensotech is not responsible for compatibility with non-
original equipment.

HARDWARE IS YOUR EXCELLENCE
WWW.ENSOTECH.LTD
Unit F, 6 Floor, Cheung Hing Shing Centre, No.23, Sha Tsui Road, Tsuen Wan,
New Territories, Hong Kong
6
THE ESC PARAMETERS ADJUSTMENT AND Swave programming App
In order to change the ESC parameters, you should purchase an optional UARTLINK programming cable.
Swave ESC programming app is free of charge !! You can find the app from Google Play™ which will automatic
install to your android. Or you can download the apk file from https://shop.ensotech.ltd to install manually. If you
decide to install the apk file manually, please make sure to un-install / remove the previous version before process to
install the new version.
This application supported by Android system only.
Click and purchase
Connect Android Device to the ESC by the programming cable. If the green LED on the UARTLINK is off, please,
check the Android device USB connection. One should note that some new Android devices utilize Type-C micro
USB. Always use high quality Type-C connectors with OTG data transfer features. Beware that some cheap adaptors
in the market have bad or even do not feature with OTG connection.
Connect the battery and switch on the ESC, your A
ndroid device will
automatically detect the USB device and ask you to choose an app
for it.
Otherwise you can launch the app manually.

HARDWARE IS YOUR EXCELLENCE
WWW.ENSOTECH.LTD
Unit F, 6 Floor, Cheung Hing Shing Centre, No.23, Sha Tsui Road, Tsuen Wan,
New Territories, Hong Kong
7
If the device is connected successfully, the color of the application icon will
change to BLUE, if it remains GREY, please, try to unplug and plug again the
USB into your Android device and wait
2 second for your android device
response. If the icon still remains grey, please, recheck all your connections.
Connection require the phones / tabs support the latest OTG. Ensotech try to
have the most compatibility but we are not guarantee and not responsible to
support every devices.
If your device uses TYPE-C USB, please make sure to use an adaptor has
OTG. If you are uncertain please do not open the package. Consults with your
sellers and other users their advice for supported model.
In case of new firmware release,
the app will show notification; you
can accept or discard update.
Chose the context menu in the
right corner and push the button
to check for updates.
Also you can find this manual at
our website
When update is completed
successfully, ESC performs one
beep and turns on a blue LED.
*During update power must be always present, otherwise ESC can be damaged!
* Before starting the firmware update you should be sure that your phone cash is quite clear and there is no
huge number of parallel process. It will be better to start phone optimization by vendor-installed app. If your phone
hasn’t it, we recommend 360 Security app.

HARDWARE IS YOUR EXCELLENCE
WWW.ENSOTECH.LTD
Unit F, 6 Floor, Cheung Hing Shing Centre, No.23, Sha Tsui Road, Tsuen Wan,
New Territories, Hong Kong
8
Now you can start to manage the settings, press “APPLY” to accept changes
After you complete managing the settings, you need to
upload all new
settings to the ESC, so click the icon on the top left comer. After uploading
process, the ESC will perform one beep and turn on a blue LED.
1. This is a resume key if you need to download the ESC current
settings to the app
2. Upload new settings to the ESC
Important: during either upload or download the settings from the ESC, power must be always present,
otherwise ESC can be damaged!
Each parameter has a detailed description

HARDWARE IS YOUR EXCELLENCE
WWW.ENSOTECH.LTD
Unit F, 6 Floor, Cheung Hing Shing Centre, No.23, Sha Tsui Road, Tsuen Wan,
New Territories, Hong Kong
9
EXPORT / IMPORT SETTINGS CONFIGURATION
Swave E App allows you export to a local file and import different settings configuration. When you will save you first
configuration in the root directory of the device internal memory will be created the folder “Swave ESC Settings”, all
other configurations will be here. For importing settings chose configuration file in this folder and apply it.
Note. For these operations, you should install any file manager to your device.
ESC PARAMETERS MONITORING
Swave Android Apps allows you control ESC state in real time. To open the state monitor you should chose “Current
state” tab in App menu.
Apps display your phone region's language included English, Chinese, French and Japanese, other than that would
be English.
Open a state tab to enter in
parameters monitor window
If radio system do not connected or
switched off throttle will lights red
color, if error occurs voltage and
temperature lights red color too
If all parameters is ok you can control
ESC state and watch main parameters

HARDWARE IS YOUR EXCELLENCE
WWW.ENSOTECH.LTD
Unit F, 6 Floor, Cheung Hing Shing Centre, No.23, Sha Tsui Road, Tsuen Wan,
New Territories, Hong Kong
10
SENSORS RECOGNITION SYSTEM
Swave E ESC has sensors recognition system. So, if you connect sensor cable to ESC the hall sensors icon will still
grey. Then if you push throttle with connected sensor cable and all is correct sensors icon becomes blue. If something
is wrong ESC detects the error and show warning icon, also, red led will ON
Initial sensor connection or sensorless
mode Working on sensor mode Error with sensor
ESC LED INDICATION
-Red led is failure indicator, there are several events that may cause red LED turn on.
-Throttle receiver is disconnected or was not calibrated – RED LED is constant ON
-Cut Off issue occurs – RED LED blinks
-Protection issue occurs – RED LED is constant ON
-Sensor issue occurs – RED LED blinks
-Blue led indicates the status of the device, if it is constant ON or blinks your device works normal otherwise try to
update it. If Update does not help, connect our support team: [e-mail] or contact your dealers.
-Turbo timing advance and Boost timing advance are BOTH zero – BLUE led blinks otherwise it is constant ON

HARDWARE IS YOUR EXCELLENCE
WWW.ENSOTECH.LTD
Unit F, 6 Floor, Cheung Hing Shing Centre, No.23, Sha Tsui Road, Tsuen Wan,
New Territories, Hong Kong
11
OTHER TERMS & CONDITIONS THAN MENTIONED ABOVE
Duration of Warranty: Ninety (90) Days from the day of purchase
Request for RMA
* You must present original / receipt (original copy) issued by your seller, otherwise repair service will be on
chargeable basis.
* Please contact Ensotech [e-mail] to request RMA form and return together with the product.
*After inspection if the result of wrong or improper used, the cost of repairs will inform and approved by customer
before the repair work started. Repairing process will take no more than 14 days.
* If the result of manufacturing quality issues, Ensotech will repair either replace to the same model without repairing
charges. If the return model are no longer available, Ensotech reserve the right to provide the same value model or a
higher grade model.
Shipping and Return (Under warranty & non-warranty)
Customer will be responsible for postage charges send the product back to Ensotech for inspection, after repair
Ensotech will pay for returning the product by post office registered air post service. Tthe shipping time would take 15
to 30 days depends on regions and traffics. Please contact us if request for faster delivery, please contact Ensotech
[e-mail] to request for additional express service charge.
Warranty also will not applied to the following matters:
Wrong polarity connection of the product
Physical damage
Contact with water or other fluids
Un-authorized parts utilization.
Using accessories not specified by Ensotech
Using over 5V servo
Using programing socket for other applications.
Not use for 1/27 and 1/28 scaled touring car models with 15mm diameters motor
Using external capacitors
Failure or defect normal wear, incorrect use, improper installation, repair or modification.
Ensotech Limited reserves rights to modify such list without notice.
In case of disputes, the decision of Ensotech Limited shall be final.
Ensotech Limited
Website https://shop.ensotech.ltd
Address: Unit F, 6 Floor, Cheung Hing Shing Centre, No.23 Sha Tsui Road, Tsuen Wan, New Territories, Tsuen Wan, Hong Kong
Tel: [phone]
Technical Support: [e-mail]
General Enquires: [e-mail]