Enviro Empress User manual

PELLET STOVE
Empress
SHERWOOD INDUSTRIES IS AN ENVIRONMENTALLY RESPONSIBLE COMPANY. THIS MANUAL IS PRINTED ON RECYCLED PAPER.
PLEASE KEEP THESE INSTRUCTIONS FOR FUTURE REFERENCE
TECHNICAL MANUAL
50-1267
PLEASE READ THIS ENTIRE MANUAL BEFORE INSTALLATION
AND USE OF THIS PELLET-BURNING ROOM HEATER. FAILURE TO
FOLLOW THESE INSTRUCTIONS COULD RESULT IN PROPERTY
DAMAGE, BODILY INJURY OR EVEN DEATH.
Contact your building or fire officials about restrictions and installation
inspection requirements in your area.

2
Table of Contents
Introduction...................................................................................................................................3
Rating Label Location...........................................................................................................3
Important Safety Data.........................................................................................................3
Safety Warnings And Recommendations................................................................................3
Installation.....................................................................................................................................5
Deciding Where to Locate your Pellet Appliance.....................................................................5
Removing Pellet Stove From Pallet........................................................................................5
Dimensions.........................................................................................................................6
Clearances to Combustibles..................................................................................................6
Alcove Clearances................................................................................................................7
Mobile Home Installation......................................................................................................7
Exhaust And Fresh Air Intake Locations.................................................................................8
Outside Fresh-Air Connection................................................................................................8
Vent Termination Requirements.............................................................................................9
Corner Through Wall Installation.........................................................................................10
Horizontal Exhaust Through Wall Installation........................................................................10
Vertical Rise with Horizontal Termination Installation (Recommended)....................................12
Through Concrete Wall With Vertical Rise Installations..........................................................12
Inside Vertical Installations.................................................................................................13
Outside Vertical Installations...............................................................................................14
Hearth Mount Installation...................................................................................................15
Installation with Exterior Mounted Exhaust Blower................................................................16
Through Wall Vertical Installation With Exhaust Blower..........................................................18
Thermostat Installed..........................................................................................................19
Slider/Damper Setting........................................................................................................19
Troubleshooting............................................................................................................................21
Wiring Diagram.............................................................................................................................24
Parts List - Components...............................................................................................................25
Parts List - Cast...........................................................................................................................27
Parts Diagram - Components..........................................................................................................29
Parts Diagram - Steel & Cast..........................................................................................................30
Warranty......................................................................................................................................31
Installation Data Sheet..................................................................................................................34

3
Introduction
* This manual is designed for the technician in conjunction with the owner’s manual. *
RATING LABEL LOCATION:
The rating label is located on the inside of the hopper lid.
IMPORTANT SAFETY DATA:
Please read this entire Owner’s Manual before installing or operating this ENVIRO Pellet
Stove. Failure to follow these instructions may result in property damage, bodily injury
or even death. Contact your local building or fire official to obtain a permit and any information on
installation restrictions and inspection requirements for your area.
To prevent the possibility of a fire, ensure that the appliance is properly installed by adhering
to the installation instructions. An ENVIRO dealer will be happy to assist you in obtaining information
with regards to your local building codes and installation restrictions.
Be sure to maintain the structural integrity of the home when passing a vent through walls, ceilings, or
roofs.
The stove’s exhaust system works with negative combustion chamber pressure and a slightly positive
chimney pressure. It is very important to ensure that the exhaust system be sealed and airtight. The ash
pan and viewing door must be locked securely for proper and safe operation of the pellet stove.
Do not burn with insufficient combustion air. A periodic check is recommended to ensure proper
combustion air is admitted to the combustion chamber. Setting the proper combustion air is achieved by
adjusting the slider damper located on the left side of the stove.
When installing the stove in a mobile home, it must be electrically grounded to the steel chassis of the
home and bolted to the floor. Make sure that the structural integrity of the home is maintained and all
construction meets local building codes.
Minor soot or creosote may accumulate when the stove is operated under incorrect conditions such as an
extremely rich burn (black tipped, lazy orange flames).
If you have any questions with regard to your stove or the above-mentioned information, please feel free
to contact your local dealer for further clarification and comments.
SAFETY WARNINGS AND RECOMMENDATIONS:
Caution: Do not connect to any air distribution duct or system.
Do not burn garbage or flammable fluids such as gasoline, naptha or engine oil.
Unit hot while in operation. Keep children, clothing and furniture away. Contact
may cause skin burns.
SOOT: Operation of the stove with insufficient combustion air will result in the formation of soot which
will collect on the glass, the heat exchanger, the exhaust vent system, and may stain the outside of the
house. This is a dangerous situation and is inefficient. Frequently check your stove and adjust the slider/
damper as needed to ensure proper combustion. See: “INSTALLATION - SLIDER/DAMPER SETTING”.

4
Introduction
ELECTRICAL: The use of a surge protected power bar is recommended. The unit must be
grounded. The grounded electrical cord should be connected to a standard 120 volts, 60 hertz electrical
outlet and also must be accessible. If this power cord should become damaged, a replacement power
cord must be purchased from the manufacturer or a qualified ENVIRO dealer. Be careful that the electrical
cord is not trapped under the appliance and that it is clear of any hot surfaces or sharp edges. This unit’s
maximum power requirement is (4.1 Amps) 500 watts.
GLASS: Do not abuse the glass by striking or slamming the door. Do not attempt to operate the stove
with broken glass. The stove uses ceramic glass. Replacement glass must be purchased from an ENVIRO
dealer. Do not attempt to open the door and clean the glass while the unit is in operation or if glass is
hot. To clean the glass, use a soft cotton cloth and mild window cleaner, gas or wood stove glass cleaner,
or take a damp paper towel and dip into the fly ash. This is a very mild abrasive and will not damage the
glass.
FLAMMABLE LIQUIDS: Never use gasoline, gasoline-type lantern fuel, kerosene, charcoal lighter
fluid, or similar liquids to start or “freshen up” a fire in the heater. Keep all such liquids well away from
the heater while it is in use.
SMOKE DETECTOR: Smoke detectors should be installed and maintained in the structure when
installing and operating a pellet burning appliance.
OPERATION: The ash pan and door must be closed securely for proper and safe operation of the pellet
stove. Also ensure all gaskets on the door are checked and replaced when necessary.
INSTALLATION: Be sure to maintain the structural integrity of your home when passing a vent through
walls, ceilings, or roofs. It is recommended that the unit be secured into its position in order to avoid any
displacement.
DO NOT INSTALL A FLUE DAMPER IN THE EXHAUST VENTING SYSTEM OF THIS UNIT.
DO NOT CONNECT THIS UNIT TO A CHIMNEY FLUE SERVING ANOTHER APPLIANCE.
FRESH AIR: Outside Fresh Air is optional. Consider all large air moving devices when installing your unit
and provide room air accordingly. Limited air for combustion may result in poor performance, smoking
and other side effects of poor combustion.
If you have any questions with regards to your stove or the above-mentioned information, please feel
free to contact your local dealer for further clarification and comments.
SINCE SHERWOOD INDUSTRIES LTD. HAS NO CONTROL OVER THE INSTALLATION OF
YOUR STOVE, SHERWOOD INDUSTRIES LTD. GRANTS NO WARRANTY IMPLIED OR STATED
FOR THE INSTALLATION OR MAINTENANCE OF YOUR STOVE. THEREFORE, SHERWOOD
INDUSTRIES LTD. ASSUMES NO RESPONSIBILITY FOR ANY CONSEQUENTIAL DAMAGE(S).
SAVE THIS INSTRUCTION MANUAL FOR FUTURE REFERENCE

5
Installation
DECIDING WHERE TO LOCATE YOUR PELLET APPLIANCE:
Figure 1: Removing Freestanding Stove From the Pallet.
Hold-down brackets.
1. Check clearances to combustibles (see INSTALLATION - CLEARANCES TO COMBUSTIBLES
and INSTALLATION - ALCOVE CLEARANCES).
2. Do not obtain combustion air from an attic, garage or any unventilated
space. Combustion air may be obtained from a ventilated crawlspace.
3. Do not install the stove in a bedroom.
4. You can vent the stove through an exterior wall behind the unit or connect
it to an existing masonry or metal chimney (must be lined if the chimney
is over 6” (15 cm) diameter, or over 28 inches² (180 cm²) cross sectional
area). An interior vent can be used with approved pipe passing through the
ceiling and roof.
5. Locate the stove in a large and open room that is centrally located in the
house. This will optimize heat circulation.
6. The power cord is 8 feet (2.43 m) long and may require a grounded extension
cord to reach the nearest electrical outlet.
REMOVING PELLET STOVE FROM PALLET:
Remove screws from the two (2) hold-down brackets that secure the Empress to the pallet. Lift the
brackets up to unhook from the chassis.

6
247/16"
(621mm)
273/8"
(695mm)
243/16"
(614mm)
153/8"
(390mm)
253/4"
(653mm)
153/4"
(400mm)
Installation
DIMENSIONS:
Figure 2: Empress Freestanding Dimensions.
Back wall
Side wall
Adjacent
wall
3"
(76mm)
3" (76mm)
8"
(203mm)
6"
(152mm)
Floor Protection
Figure 3: Minimum Clearances to Combustibles for
Freestanding Empress.
CLEARANCES TO COMBUSTIBLES:
These dimensions are minimum clearances but it
is recommended that you ensure sufficient room
for serving, routine cleaning and maintenance.
This pellet stove requires floor protection. The
floor protection must be non-combustible,
extending beneath the stove the full width and
depth of the unit including 6“ (150 mm) in front
for ember protection.
Minimum Hearth Pad Size:
Width: 27” (686 mm)
Depth: 32  “ (816 mm)

7
This unit may be installed in an alcove. Maintain
the clearances to combustibles shown in Figure 4.
Install vent at clearances specified by the vent
manufacturer.
Minimum Width
48" (1219mm)
Minimum Height
48" (1219mm)
Maximum Depth
30" (760mm)
Installation
ALCOVE CLEARANCES:
Figure 4: Alcove Clearances.
MOBILE HOME INSTALLATION:
● Secure the heater to the floor using the holes in the leg of the appliance (normally used for the leveling
legs).
● Ensure the unit is electrically grounded to the chassis of your home (permanently).
Ground wire directly
connected to metal chassis.
Hearth Pad
Flooring
Steel Frame 1/4" Lag bolts
securely fastened
Figure 5: Mobile Home Install Mounting.
WARNING: Do not install in a room
people sleep in.
CAUTION: The structural integrity
of the manufactured home floor,
wall and ceiling/roof must be
maintained
• Outside fresh air is mandatory. Secure
outside air connections directly to
fresh air intake pipe and secure with
three (3) screws evenly spaced.

8
77/16"
(189mm)
43/8"
(112mm)
31/16"
(77mm)
99/16"
(243mm)
EXHAUST
Base of unit to center of flue 9 9/16” (243 mm)
Center of unit to center of flue 3 1/16” (77 mm)
FRESH AIR INTAKE.
Base of unit to center of intake 7 7/16” (189 mm)
Center of unit to center of flue 4 ” (112 mm)
OUTSIDE FRESH-AIR CONNECTION:
Outside fresh air is mandatory when installing this unit
in airtight homes and mobile homes.
A Fresh-air intake is strongly recommended for all
installations. Failure to install intake air may result in improper
combustion as well as the unit smoking during power failures.
When connecting to an outside fresh air source, do not use
plastic or combustible pipe. A 2” minimum (51 mm) ID (inside
diameter) steel, aluminum or copper pipe should be used. It is
recommended, when you are installing a fresh air system, to
keep the number of bends in the pipe to a minimum.
Installation
EXHAUST AND FRESH AIR INTAKE LOCATIONS:
INSTALL VENT AT CLEARANCES SPECIFIED BY THE VENTING MANUFACTURER
 
 




Figure 7: Outside Air Connection.
Figure 6: Inlet and Outlet Location.

9
hot enough to cause burns if touched by children. Non-combustible shielding or guards may be required.
3. Termination must exhaust above the inlet elevation. It is recommended that at least five feet of vertical pipe
be installed outside when the appliance is vented directly through a wall, to create some natural draft to
prevent the possibility of smoke or odor during appliance shut down or power failure. This will keep exhaust
from causing a nuisance or hazard from exposing people or shrubs to high temperatures. In any case, the
safest and preferred venting method is to extend the vent through the roof vertically.
4. Distance from the bottom of the termination and grade is 12” (30 cm) minimum. This is conditional upon
the plants and nature of grade surface. The exhaust gases are hot enough to ignite grass, plants and
shrubs located in the vicinity of termination. The grade surface must not be lawn.
5. If the unit is incorrectly vented or the air to fuel mixture is out of balance, a slight discoloration of the
exterior of the house might occur. Since these factors are beyond the control of Sherwood Industries Ltd,
we grant no guarantee against such incidents.
NOTE: Venting terminals shall not be recessed into walls or siding.
Installation
VENT TERMINATION REQUIREMENTS:
IT IS RECOMMENDED THAT YOUR PELLET STOVE BE INSTALLED BY AN AUTHORIZED DEALER/INSTALLER.
Figure 8: Use in conjunction with Table 1 for allowable exterior vent termination
locations.
Table 1: Use in conjunction with Figure 8 for allowable exterior vent termination locations.
Letter Minimum Clearance Description
A 24 in (61 cm) Above grass, top of plants, wood, or any other combustible materials.
B 48 in (122 cm) From beside/below any door or window that may be opened.
C 24 in (61 cm) From above any door or window that may be opened.
D 24 in (61 cm) To any adjacent building, fences and protruding parts of the structure.
E 24 in (61 cm) Below any eave or roof overhang
F 12 in (30 cm) To outside corner.
G 12 in (30 cm) To inside corner, combustible wall (vertical and horizontal terminations).
H 3 ft (91 cm) within a height of
15 ft (4.5 m) above the meter/
regulator assembly
To each side of center line extended above natural gas or propane meter/
regulator assembly or mechanical vent.
I 3 ft (91 cm) From any forced air intake of other appliance
J 12 in (30 cm) Clearance to non-mechanical air supply inlet to building, or the combustion air
inlet to any appliance.
K 24 in (61 cm) Clearance above roof line for vertical terminations.
L 7 ft (2.13 m) Clearance above paved sidewalk or paved driveway located on public property.
Air Supply Inlet Gas Meter Restriction Zone
(Termination not allowed)
Termination Cap
G
G
Opens
Opens
Opens
DF
B
B
AI
H
K
G
G
L
C
E
1. Do not terminate the
vent in any enclosed or
semi-enclosed areas such
as a carport, garage,
attic, crawlspace, narrow
walkway, closely fenced
area, under a sundeck
or porch, or any location
that can build up a
concentration of fumes
such as stairwells,
covered breezeway, etc.
2. Vent surfaces can become

10
Figure 9: Corner Installation.
3"
(7.5 cm)
3"
(7.5 cm)
Fresh Air Intake
Wall thimble
manufactured
by pellet vent
manufacturer.
Installation
CORNER THROUGH WALL INSTALLATION:
HORIZONTAL EXHAUST THROUGH WALL INSTALLATION:
Vent installation: install vent at clearances specified by the vent manufacturer.
A chimney connector shall not pass through an attic or roof space, closet or similar concealed spaces,
or a floor, or ceiling. Where passage through a wall or partition of combustible construction is desired,
the installation shall conform to CAN/CSA-B365 Installation Code for Solid-Fuel-Burning Appliances and
Equipment. Only use venting of L or PL type with an inside diameter of 3 or 4 inches (7.6 or 10.1 cm).
1. Choose a location for your stove that meets the requirements stated in this manual and allows
installation with the least amount of interference to house framing, plumbing, wiring, etc.
2. Install a non-combustible hearth pad (where necessary).
3. Place the appliance 15” (37.5 cm) away from the wall. If the stove is to be set on a hearth pad, set
the unit on it.
4. Locate the center of the exhaust pipe on the stove. Extend that line to the wall. Once you have located
the center point on the wall, refer to pellet vent manufacturer installation instructions for correct hole
size and clearance to combustibles.
5. Install the wall thimble as per the instructions written on the thimble. Maintain an effective vapour
barrier in accordance with local building codes.
6. Install a length of 3” (76 mm) or 4” (101 mm) vent pipe into the wall thimble. The pipe should install
easily into the thimble.
7. Install the fresh air intake (see INSTALLATION - OUTSIDE FRESH AIR CONNECTION).
8. Connect the exhaust vent pipe to the exhaust pipe on the stove. Seal the connection with high
temperature silicone.
9. Push the stove straight back, leaving a minimum of 3” (76 mm) clearance from the back of the stove
to the wall. Seal the vent pipe to the thimble with high temperature silicone.

11
Exhaust
3" (75mm) or 4" (100mm)
"PL" or "L" Vent
Wall Thimble
45oElbow with Screen
or Termination Cap
High Temperature RTV
Silicone Required
Fresh Air Intake
Wall framing
Wall thimble
Termination cap
Vent pipe
Horizontal frame
for thimble
 
• This is due to the back pressure in the
exhaust caused by airflow around the
structure.
• All sections of pipe must have three (3)
screws evenly spaced and all horizontal
and vertical vent sections located within
the house must have a bead of high
temperature silicone installed on the
male end of the pipe before installation to
create a gas tight seal.
• The termination must be 12 inches (30
cm) from the outside wall and 12 inches
(30 cm) above the ground.
• A 45° elbow with a rodent screen may be
used in place of the termination cap (or
stainless steel termination hood).
Installation
Figure 10: Straight through wall Installation.
10. The pipe must
extend at least
12” (30 cm) away
from the building.
If necessary, bring
another length of
pipe (PL type) to the
outside of the home
to connect to the
first section. Do not
forget to place high
temperature silicone
around the pipe that
passes through the
thimble.
11. Install a vertical pipe,
or if all requirements
for direct venting
are met, install
vent termination. The stainless steel cap termination manufactured by the vent manufacturer is
recommended. However, when the vent terminates several feet above ground level and there are no
trees, plants, etc. within several feet, a 45° elbow can be used as termination. The elbow must be
turned down to prevent rain from entering.
NOTE:
• Some horizontal through wall installations may require a “T” and 3 to 5 feet (91 to 152 cm) of vertical
pipe outside the building to help naturally draft in the unit.
• This may be required if a proper burn cannot be maintained, after the stove has been tested and the
airflow set.
Figure 11: Straight through Wall Installation - Side View.

12
Installation
VERTICAL RISE WITH HORIZONTAL TERMINATION INSTALLATION (RECOMMENDED):
A 45° elbow with a rodent screen may be used
in place of the termination cap (or stainless
steel termination hood).
THROUGH CONCRETE WALL WITH VERTICAL RISE INSTALLATIONS:
A 45° elbow with a rodent screen may be used
in place of the termination cap (or stainless
steel termination hood).
This is the recommended installation to use if
there is a concrete or retaining wall in line with
exhaust vent on pellet stove.
The termination must be 12” (305 mm) from
the outside wall and 12” (305 mm) above the
ground.
Figure 13: Vertical rise with Horizontal Termination.
Figure 12: Through Wall with Horizontal Termination.
Wall framing
Wall thimble
Termination
cap
Vertical section
of vent pipe
Horizontal frame
for thimble
Clean out tee
90°elbow
 
Concrete
Wall
Wall framing
Wall thimble
Termination cap
Vertical section
of vent pipe
Clean out tee
 
Wall strap
90°elbow
Horizontal frame
for thimble

13
Storm Collar
Roof Flashing
Roof Rafters
Fire Stop with
Support Collar
Ceiling Joist
Vertical Vent Pipe
Clean Out Tee
with Pipe Adapter
ENVIRO Empress
Note:
All vent sections must maintain
3" (76mm) clearances to
combustibles.
Rain cap - ensure cap is at
least 2 feet (610mm) above
the roof at the lowest point
Installation
INSIDE VERTICAL INSTALLATIONS:
1. Choose a stove location that is ideal. See the section “INSTALLATION - DECIDING WHERE TO LOCATE YOUR PELLET
APPLIANCE.”
2. Place the unit on the hearth pad (if installed on a carpeted surface) and space the unit in a manner
so when the pellet vent is installed vertically, it will be 3” (76 mm) away from a combustible wall.
3. Locate the center of the fresh air intake pipe on the unit. Match that center with the same point on
the wall and cut a hole about 2” (52 mm) in diameter.
4. Install the fresh air intake pipe.
5. Install the tee with clean out.
6. Install the pellet vent upward from there. When you reach the ceiling, make sure that the vent goes
through the ceiling fire stop. Maintain a 3” (76 mm) distance to combustibles and keep attic insulation
away from the vent pipe. Maintain an effective vapor barrier.
7. Finally, extend the pellet vent to go through the roof flashing.
8. Ensure that the rain cap is approximately 24” (610 mm) above the roof.
Figure 14: Inside Vertical Installation.

14
Installation
OUTSIDE VERTICAL INSTALLATIONS:
To accomplish a outside vertical pipe installation, follow steps 1 through 5 in the “INSIDE VERTICAL
INSTALLATIONS” section and then finish it by performing the following (refer to Figure 15).
1. Install a tee with clean out on the outside of the house.
2. Install PL vent upward from the tee. Make sure that you install support brackets to keep the vent
straight and secure.
3. Install ceiling thimble and secure the flashing as you go through the roof.
4. Ensure that the rain cap is approximately 24” (610 mm) above the roof.
Rain cap
Flashing
24"
(61 cm)
3"
(7.5cm)
Tee with
cleanout
Fresh air
intake
3" (7.5 cm)
Clearance
Support
bracket
Type "L"
vent
Figure 15: Outside Vertical Installation.

15
Storm Collar
Existing Masonary Flue
Flexible Vent Connector
(use this 5ft section of pipe
to vent past the fireplace
damper or smoke shelf)
Seal Plate
Fireplace Damper
Location
Vertical Vent Pipe (single
wall stainless flex pipe or
solid PL vent)
Existing Fireplace
ENVIRO Empress
Clean Out Tee
Rain cap - ensure cap is at
least 2 feet (610mm) above
the roof at the lowest point
1. Lock fireplace damper in the open
position.
2. Install a positive flue connector at the
fireplace dampers.
3. Connect a clean-out tee or a 90° elbow to
the exhaust pipe.
4. Install flexible stainless steel liner or listed
pellet vent to the top of the chimney.
Floor
Protection
Combustible Floor
Masonry Fireplace
Min 6"
(150 mm)
Mantel
Minimum 8" (20 cm)
from top of stove
Damper Removed
or Fastened Open
Clean-out
Fresh-air intake
should com from
chimney. If holes
already exist fresh-air
intake can be taken
through back of the
fireplace or through
the ash dump.
Installation
HEARTH MOUNT INSTALLATION:
Figure 16: Hearth Mount - Side View.
Figure 17: Hearth Mount - Over View.

Install blower
motor onto
exhaust blower
housings.
Completed assembly.
Exhaust Motor
Cover Plate
Access Panel
16
Installation
INSTALLATION WITH EXTERIOR MOUNTED EXHAUST BLOWER:
The Empress can be equipped with an externally mounted exhaust blower (PART #20-070). This optional
kit will include all components necessary to install the exhaust blower on any external vertical wall
surface.
Choose a location for your stove that meets the requirements stated in this manual and allows installation
with the least amount of interference to house framing, plumbing, wiring, etc.
Included in the exterior mounted exhaust blower kit
are: 1 - Exhaust blower housing box.
1 - Blower cover plate.
1 - Hardware bag
1. Open the left side of the unit and disconnect the
exhaust blower wires from the harness. Remove
the exhaust blower by undoing the six (6)  hex
head sheet metal screws that fasten the blower to
the housing.
2. Remove the back grill from the exterior exhaust
vent housing and remove the round cover plate
installed on the blower housing.
3. Install the round cover plate over the gasketed
opening in the stove where the exhaust motor was
removed from.
4. Install the exhaust blower motor in the Exterior Vent
Housing Box onto the exhaust blower housing.
5. Follow the procedures for INSTALLATION - HORIZONTAL
EXHAUST THROUGH WALL INSTALLATION. Place the unit in
Figure 19: Exterior Exhaust Blower.
the desired location. Cut the hole in the wall at the desired location. Install a wall thimble.
6. Drill holes in the wall thimble in the corresponding locations for wire and fresh air if needed. Install
wire clamps and feed wire through the hole in the thimble into the house. Tighten clamp on wire and
attach green ground wire (at the symbol) with the screw and star washer provided.
7. Attach a short or an adjustable section of 3” of double wall pellet vent through the wall thimble to
the stove. Seal all joints with
silicone. Maintain clearances to
combustibles.
8. Apply silicone to the pipe in
the Exhaust Box, slide the pipe
into the exhaust vent. Mount
the Exhaust Box to the house.
Reinstall the back grill on the
Exterior Vent Housing Box.
Apply normal venting practices
when installing the vertical
vent pipe.
Figure 18: Removing Exhaust Blower.

17
TO SUPPLY POWER TO THE EXHAUST BLOWER:
Install an amour coated electrical cable from the exhaust blower housing, through the wall thimble, and
attach to the pre-drilled hole in the left hand rear hopper pillar. Hook up to wires from the wiring harness
for the exhaust blower. All electrical connections must be in accordance with local code requirements (see
WIRING DIAGRAM).
Installation
Vent termination cap
(stainless steel termination
hood) or 45° elbow with
rodent screen
90° elbow
Wall strap
(recommended with
use of vent pipe)
Exterior blower
and housing
Vent pipe or 2 foot
(610 mm) riser
Pipe adapter (if
using 2 foot riser)
Wall framing
Wall thimble
Horizontal frame
for thimble
Armour cable supplying
power to exterior blower
Siding
Figure 20: Exhaust Blower Installation; Horizontal Termination.
9. Connect the wires in the stove. Re-install the left side access cover to the stove and the back grill on
the exterior vent housing.
10. Set the Slider Damper as described in the INSTALLATION - SLIDER/DAMPER SETTING“ section.
NOTE:
Ensure that all vent connections are installed by placing three (3) screws evenly spaced and a small bead
of high temperature silicone at each chimney connection. Also ensure that all vertical vent sections are
properly supported and that all clearances to combustibles are maintained in accordance with the vent
manufacturer’s specifications.

18
Storm Collar
Roof Flashing
Roof Rafters
Roof Sheathing
Ceiling Joist
Vertical Vent Pipe
Outside Vent
Termination
Exterior Wall
Sheathing
Rain cap - ensure
cap is at least 2'
(610mm) above
the roof at the
lowest point
Installation
THROUGH WALL VERTICAL INSTALLATION WITH EXHAUST BLOWER:
Refer to INSTALLATION - INSTALLATION WITH EXTERIOR MOUNTED EXHAUST BLOWER and INSTALLATION - OUTSIDE VERTICAL
INSTALLATIONS. Ensure that vent pipe is properly secured to wall using wall straps. Maintain clearances to
combustibles on vent pipe as well as unit.
Figure 21: Exhaust Blower Installation; Vertical Termination.

19
Installation
THERMOSTAT INSTALLATION:
1. Install the wall thermostat in a location that is not to close too the unit but will effectively heat the
desired area.
Remove jumper
wire and install
thermostat wires here.
Figure 22: Thermostat wire placement.
2. Install a 12 or 24 Volt Thermostat using an 18 x 2
gauge wire from the unit to the thermostat.
If the unit has been placed in the HI / LOW mode, the unit
will be taken to a low or idle setting when the thermostat
is not calling for heat. When the thermostat calls for
heat, the unit will go to the setting that is displayed on
the control board Heat Indicator. If the heating load is
not great enough when the stove is on low, the high limit
switch will turn the stove off and the switch will have to
be manually reset. To reset the high limit switch, remove
the right cabinet side. The switch is found behind the
control panel. Avoid setting off the high limit switch.
Figure 24: Slider / Damper
A Qualified Service Technician
or Installer must set the Slider
Damper.
Note: Some parts have been
removed in order to see the
components more clearly
Slider Damper
Plate
Exhaust
Channel
Exhaust
Blower Motor
Door Cut
Away
Figure 23: Slider / Damper Collars
SLIDER/DAMPER SETTING:
THE SLIDER / DAMPER MUST BE SET AT TIME OF INSTALLATION, IT IS USED TO REGULATE
THE AIRFLOW THROUGH THE PELLET STOVE. The slider damper is located on the lower left side.

20
Installation
The low burn collar must be set on a hot stove; run the unit on low for 30 minutes, and place a Magnahelic
Pressure Gauge in the firebox (test port is located in the center of the stove just below the door opening).
Set the slider at 0.11” W.C. (30 Pa) for the rebox vacuum and lock the set collar in place (refer to Figure
23). Some fuels may require higher or lower settings.
Figure 25: Efficient Flame.
The easiest way to make sure that an efficient flame is achieved is to understand the characteristics of
the fire.
• A tall, lazy flame with dark orange tips requires more air – Open slider (pull out) slightly.
• A short, brisk flame, like a blowtorch, has too much air – Close slider (push in) slightly.
• If the flame is in the middle of these two characteristics with a bright yellow/orange, active flame
with no black tips then the air is set for proper operation.
SPECIAL NOTES:
Pellet quality is a major factor in how the pellet stove will operate. If the pellets have a high moisture
content or ash content the fire will be less efficient and has a higher possibility of the fire building up and
creating clinkers (hard ash build-up). If this happens, pull the Slider Damper out slightly to increase the
air flow to the fire.
The combustion exhaust blower is a
variable speed blower controlled by
the heat output setting. This blower
will increase or decrease speed as
the heat output button is turned up
or down.
• If the fire should happen to go out
and the heat output indicator has
been set on the lowest setting, the
Slider Damper may need to be pushed
in slightly, decreasing the air in the
firebox. Or the Low Feed Trim can be
adjusted.
• If, after long periods of burning, the
fire builds up and overflows the burn
pot or there is a build up of clinkers,
this could be a sign that the pellet
quality is poor, or the Air to Fuel ratio
is wrong. This requires more primary
air, the slider damper must be pulled
out to compensate. Pulling the slider
damper out gives the fire more air.