Enviro Evolution EF5 User manual

November 2011
Enviro Evolution EF5 Freestanding
Wood Pellet Burning Heater
Enviro Evolution EF5 Freestanding
Wood Pellet Burning Heater
Installation Specications
Safety testing of EF5 Evolution FS CB Pellet Burning Heater to
AS/NZS 2918. ARS 09/1981 & 08/1902
Emissions: 07/1664
Flue Kit Testing to AS/NZS 2918 AppF:05/1185

2
November 2011
Installation
Dimensions – Evolution EF5 Freestanding
Installation Clearances & Specications
Minimum clearances shown are in millimetres. All Enviro res are tested to AS/NZS2918:2001.
Specications were correct at time of printing but may alter and those detailed below should be used as
a guide only. Refer to the Installation and Operation Manual supplied with every Enviro Pellet Fire or if
in doubt, consult your Switch Retailer. Refer to Safety Test 09/1981 for all clearances to combustibles.
Clearances to Combustibles
22 1/4"
(565 mm)
34 5/16"
(871 mm)
23 7/16"
(595 mm)
5 5/8"
(144 mm)
26 3/8"
(670 mm)
28"
(711 mm)
24 3/8"
(619 mm)
B
J
H
A
E
External Flue
J
J
F
B
IF
E
Enviro Evolution EF5 Pellet Fire
Clearance to Combustibles
B
C
AE
D
G
F
B
F
G
E
Internal Flue
Location Dimension
(mm)
A 100
B 150
C* 50
D ~210
E N/A
F 75
G* 50
H 100
I* 50
J* 25
Freestanding
Clearances
* from shielded ue
Note: AS/NZS 2918
requires a minimum
of 100mm clearance
for any side requiring
access.
Note: These are
minimum clearances to
combustibles. Actual
installation distances
may be greater.
Note: The above clearance to combustibles on the ue are only applicable within the re envelope. Clearance outside this e.g.at a ceiling / wall thimble reverts to 25mm as per ARS ue
test 05/1185.

3
November 2011
Location of the Pellet Fire
Installation of the Enviro Evolution Wood Pellet Burning Heater should be undertaken by an
experienced installer. Please read the Evolution Owners/Technical Manual thoroughly before
commencing installation as failure to follow the instruction could cause damage to the pellet
re or property.
Positioning the re:
Generally the Evolution should be installed in a centrally located position within the home.
When deciding where to position the appliance in your room you need to consider the following:
• Location of a power source
• The Evolution has a convection fan which blows air through tubes in the direction that
the re faces, for optimum performance this location should be in a large room centrally
located.
• The Evolution comes with its own hearth pad. This complies with the hearth requirements
and the re can be installed on a combustible surface.
• The Evolution has been Safety Tested to AS/NZS 2918 using the Davins manufactured
ue. Test Report ARS 05/1185. Installation is not exclusive to these nominated kits,
though alternative ue should only be considered following consultation with your local
council.
• Please consult page 2 for the required clearances to combustible material also ensure
the position of structural elements near the proposed ue.
• Because of the positive pressure in the ue, sealing of all 75mm stainless joints is
mandatory – use high temperature sealant. Both inner and outer ue joints must be
riveted.
• Seismic Restraint: Please see page 6 for requirements.
• Warranty: To validate warranty following installation a copy of the completed Warranty/
Producers Statement must be forwarded to: Switch- Fax [phone].

4
November 2011
Internal Standard Flue Kit (50)
Internal Standard Flue Kit
Each 50 Internal Standard Flue Kit contains:-
ytitnauQnoitpircseDoNtraP
1Galvanised outer liner
ø100mm x 900mm long 1
4
3
2
1
1
1
1
1
1
2
2 Stainless steel inner liner
ø75mm x 900mm long
4a Black p/coat outer liner
ø100mm x 900mm long
5Inner/outer ue liner spacer
6c Ceiling thimble ø107mm hole
7c Ceiling decor plate
ø107mm hole – white
8Rain cap 75mm
9Rain Cap 100mm
10b Elbow 45° – ø75mm stainless
–black (painted)
12H T-adaptor/cleanout – ø75mm
–black (painted)
23 Support angle 950mm long
– 50mm x 50mm sides
This ue kit may be used in new and replacement
applications in rooms with stud height of 2.4m. The
overall height of the ue is 3.6m. The visible u e is
nished in black and the ceiling plate is white. T he
support angles for securing the liner to the ceilin g are
not shown. Kit is supplied in a carton.
Heat-resistant
oor protector
Seismic restraint
(to be tted)
50mm minimum clearance if lined ue
600mm from
roof
penetration
~210 mm
150mm
(minimum)
Note: The Davin 50 Internal Standard Flue
Kit complies with AS/NZS 2918:2001 as per
Applied Research Test Report 05/1185, dated
15 September 2005.
All res must be installed by a qualied
installer as per the manufacturer’s
instructions and AS/NZS2918:2001.
50
To order : Telephone [phone]. Fax [phone] [e-mail] 2006
Drawing representative only - not to scale.
This ue kit may be used in new and replacement
applications in rooms with stud height of 2.4m.
The overall height of the ue is 3.6m. The visible
ue is nished in black and the ceiling plate is
white. The support angles for securing the liner to
the ceiling are not shown. Kit is supplied in carton.

5
November 2011
External Standard Flue Kit (51)
Each 51 External Standard Flue Kit contains:-
ytitnauQnoitpircseDoNtraP
1Galvanised outer liner
ø100mm x 900mm long
2 Stainless steel inner liner
ø75mm x 900mm long
5Inner/outer ue liner spacer
6w Wall thimble – 2 pieces
ø102mm holes
6s Sot thimble ø107mm hole
7w Wall decor plate
ø102mm hole – white
8Rain cap 75mm
9Rain Cap 100mm
26 Lined T-adaptor
This ue kit may be used in new and replacement
applications with the ue penetrating the wall behind
the re, running vertically up an outside wall and
penetrating the sot. The overall height of the f lue is
3.6m. All visible ue has a galvanised nish, and can be
powdercoated on request. Kit is supplied in a carton.
Note: The Davin 51 External Standard Flue
Kit complies with AS/NZS 2918:2001 as per
Applied Research Test Report 05/1185, dated
15 September 2005.
All res must be installed by a qualied
installer as per the manufacturer’s
instructions and AS/NZS2918:2001.
Heat-resistant
oor protector
Seismic restraint
(to be tted)
600mm from
roof penetration
100mm
(minimum)
150mm
(minimum)
External Standard Flue Kit51
4
4
2
1
1
1
1
1
1
To order :December 2006 Telephone [phone]. Fax [phone] [e-mail]
Drawing representative only - not to scale.
This ue kit may be used in new and replacement
applications with the ue penetrating the wall
behind the re, running vertically up an outside
wall and penetrating the soft. The overall
height of the ue is 3.6m. All visible ue has a
galvanised nish, and can be powdercoated on
request. Kit is supplied in a carton.

6
November 2011
Flashing Options:
Decktite - For all Steel Roof Proles
Please circle the ashing option to be used. When considering an alternative method please consult
your local council.
SEISMIC RESTRAINT:
All installation scenarios for the Enviro Evolution EF5 require the use of hold-down anchors (one on
each side)
Fixing to Concrete Floor:
Minimum M8 expansion anchors (M10 recommended) or min M8 epoxy- set anchors.
Approved Anchors: Expansion Anchors-Ramset Dynabolt and Trubolt, Hilti HAS.
Epoxy-set Anchors – Ramset Epcon, Ramset Chemset and Hilti HVU.
Fixing to Timber Floor Framing:
Minimum 14g x 60 screws (6.3mm diameter) or M10 X 90 coach-screws. These shall be xed a minimum
of 40mm into the centre-line of the existing oor joists. If screws cannot be installed directly into an
existing oor joist, solid blocking between joists (min size 90x45) shall be provided.