Enviro 0202PPCT02 User manual

Enviro Technologies
S-12,Top class Enclave, Nr. Bhoidapada bus stop, Sativali Road, Vasai (E), Thane -
401208,
Tel: [phone] Web: www.enviroworld.in
Data Storage Unit
Manual
Ver. 1.7T
Model: ETS-DSU-G01A01(0202PPCT02)

ETS-DSU- G01A01(0202PPCT02) [ver. 1.7T] Page i
History
Sr.
No
Manual
Version
Date
Author
Approved By
Remarks
1
1.0
31/08/10
Yogesh
Prashant
-
2
1.1
02/11/10
Yogesh /
Sanjay
Prashant
1. Setting of temperature set point and
humidity set point has been made
common.
2. Fast key response auto increment and
decrement.
3. Faster scanning and averaging of sensor
readings.
4. Fast display updating.
3
1.6T
14/08/17
Chetan
Sanjay
1. Manual prepare as per Temperature (ETS-
DSU-G01A01) Model.
2. Removed Data Storage Type, our device
dispatched with fixed data type.
3. Correction in troubleshooting chart.
4
1.7T
29-10-18
Akshada
sanjay
1. Added PID selection menu

ETS-DSU- G01A01(0202PPCT02) [ver. 1.7T] Page ii
TABLE OF CONTENT
History ............................................................................................................................................. i
Product Selection (Model No.):........................................................................................................1
Introduction.....................................................................................................................................1
LED Indications.......................................................................................................................................1
Operation Keys........................................................................................................................................2
Display Message.......................................................................................................................................2
Product Specification and Features.................................................................................................3
Keypad Functions ............................................................................................................................4
1. ADMIN LOGIN .........................................................................................................................................4
2. DISPLAY MODE.......................................................................................................................................5
3. CONTROLLER NO: ..................................................................................................................................5
4. PRINT CONTROL.....................................................................................................................................5
4.1 Set Header Page For Print Start.......................................................................................................................6
4.2 Cancel Old Printing........................................................................................................................................6
4.3 Print Current Reading.....................................................................................................................................6
4.4 Reset Page No................................................................................................................................................7
4.5 Reset Print......................................................................................................................................................7
4.6 Reset All Memory. .........................................................................................................................................7
5. PRINT LAST PAGES.................................................................................................................................8
6. PRINT DATA DATE WISE .......................................................................................................................8
7. PRINT INTERVAL....................................................................................................................................9
8. PAGE LENGTH.........................................................................................................................................9
9. SET DECIMAL POINT..............................................................................................................................9
10. MEMORY USED STATUS......................................................................................................................10
11. ETS-DSU NUMBER................................................................................................................................10
12. SETTING DATE TIME............................................................................................................................11
13. CONTRAST CONTROL..........................................................................................................................11
14. MEM ALARM PROG ..............................................................................................................................11
15. SET STABILIZATION (Optional Factory setting) ....................................................................................12
16. ALARM ACKNOWLED. (Optional Factory setting).................................................................................12
17. PID SELECTION.....................................................................................................................................13
Printer Remarks.............................................................................................................................14
ETS-DSU-G01A01(0202PPCT02) Connection Details..................................................................16
Printer Connection Details ............................................................................................................16
System Connection Details.............................................................................................................17
Installation Note ............................................................................................................................18
Troubleshooting Chart:..................................................................................................................19

ETS-DSU- G01A01(0202PPCT02) [ver. 1.7T] Page 1
Product Selection (Model No.):
SR.NO
Model No
Description
1
ETS-DSU G01A01(0202PPCT02)
Graphical/Temperature/PID/1Channels
Introduction
ETS-DSU-G01A01(0202PPCT02) (DSU + Display) unit is a new version of ETS-DSU 2.1
Hardware PC & Parallel Printer interface, where display is interfaced with ETS-DSU-
G01A01(0202PPCT02) on RS 485 internally. Display consists of 128X64 GLCD display and 4
programming keys, which are used for programming of different display parameters, ETS-DSU-
G01A01(0202PPCT02) parameters and also to display the controller parameters. This display is
connected internally on same RS485 cable on which controllers are connected.
LED Indications
CTx
Controller data transmit signal
CRx
Controller data receive signal
ALm
Key press buzzer indication and Memory full indication
PRx
Printer data transmit signal
PTx
Printer data receive signal
PrDt
Printer connection and Page detection signal
ENVIRO TECHNOLOGY 01
CH PV SV
T1 23.5 25.0 °C
M 14/09/10 12:00

ETS-DSU- G01A01(0202PPCT02) [ver. 1.7T] Page 2
Operation Keys
SEL
Select function or Entering Menu.
Press this key second times then exist the menu.
This key used for exit to the parameter setting.
INC
Scroll the menu parameter
Increments numerical data for parameter setting.
To fast increment press key for 3 sec it will increment automatically by one, further pressing of key
will increment count by 10.
DEC
Scroll the menu parameter
Decrements numerical data for parameter setting.
To fast decrement press key for 3 sec it will decrement automatically by one, further pressing of key
will decrement count by 10.
ENT
Entering Menu parameter.
Enter or Set the data for parameter.
Display Message
CH
Channel No
PV
Process Value
M
PC OR PRINTER MEMORY INDICATION
Also display on Same location at Date time in Scrolling Percentage of
Printer and PC Memory indication with Date time.
Time & Date
This display on bottom of the display.
Here display in scrolling mode if event is occurs it shows following data
1) Alarm Indication
2) Memory Alarm massage
3) Stabilization mode(Major enable, Minor enable and stabilization period)
Display Header
At the TOP Display header (settable.)
01
This is ETS-DSU-G01A01(0202PPCT02) UNIT ID number.
°C
This is temperature unit.
This symbol indicates for connection of Printer.
ENVIRO TECHNOLOGY 01
CH PV SV
T1 23.4 25.1 °C
M 14/09/10 12:00

ETS-DSU- G01A01(0202PPCT02) [ver. 1.7T] Page 3
Product Specification and Features
Features and Specifications of ETS-DSU G01A01(0202PPCT02)
Sr.
Specifications
Description
1
Type
:
Microcontroller based Electronic device with Printer and 1PID controller
Interface.
2
Display
:
128 X 64 Alphanumeric Graphical display
3
Keypad
:
Total 4 Keys
Function keys =>SEL, INC, DEC, ENT.
4
Transaction capacity
:
Up to max transaction for PID controller.
1. 4500 for 1 PID controller
5
Power supply
:
12VDC @ 2A
12 watts
6
Communication Port
:
RS 485 (PID Communication)
RS 485 (PC Communication)
Parallel Printer interface
7
Printers supported
:
EPSON LX-300+ (Dot Matrix)
8
Size
:
96x96mm
9
Weight
:
270gm
10
Keypad functions
Admin Login
:
To Access the parameters of display unit
Display Mode
:
To set display unique #
Controller No.
:
To set no. of PID Data to be display.
Print Control
:
Different Print Controls settings.
Print Last Pages
To Print old PROCESS data from ETS-DSU-G01A01(0202PPCT02)
page wise.
Print form Date
:
To Print old PROCESS data from ETS-DSU-G01A01(0202PPCT02)
date wise.
Print Interval
:
To set polling time in minutes on ETS-DSU-G01A01(0202PPCT02)
Page Length
:
To Set Page Length on ETS-DSU-G01A01(0202PPCT02)
Set Decimal Point
:
To Remove/Set Decimal point
Memory Used Status
:
Display Memory Used Status.
Set DSU Number
:
Set ETS-DSU-G01A01(0202PPCT02) UNIT ID
Set Date Time
:
Set Time and Date for unit.
Contrast Control
:
Set contrast
Mem. Alarm Prog
:
Programmable Memory Alarm for PC & Printer memory.
Set Stabilize
:
Setting of stabilization period mode (Major stabilization and Minor
stabilization (optional factory setting)).
Alarm Acknowledged
:
Acknowledged different alarms and stabilization(Optional Factory setting)
PID SELECTION
:
Selects PID from given PIDs (PXF4, PXR4 and OMRON)
Back To Main
:
This function used to exit the Menu with logoff.
Other feature
PRINTER REMARKS
:
Printer message.

ETS-DSU- G01A01(0202PPCT02) [ver. 1.7T] Page 4
Keypad Functions
1. ADMIN LOGIN
This is used to Access the various parameters of ETS-DSU G01A01(0202PPCT02). To Log
In go to Admin Login menu using “SEL” Key and enter ID NO 10 and password value as 1.
Now user will have access for setting parameters of ETS-DSU G01A01(0202PPCT02). To
log out just go to Admin Login menu once again and press “ENT” key. Program
automatically exit from Admin menu after 60 Sec (NOTE: If any key is not press within 60
sec during Program mode then you will exit from Program mode. To enter again program
mode you must Login by using Admin Login Menu)
User must enter the ID No 10 with help of “INC”key and “DEC” Key after then press
“ENT”Key. Then you enter Password “1”using same keys
For any incorrect ID or Password entered, ETS-DSU-G01A01(0202PPCT02) display
message “Admin Login Fail…” .If the ID and Password is correct then ETS-DSU-
G01A01(0202PPCT02) display message “Admin Login OK”
ENVIRO TECHNOLOGY 01
Display Mode
Controller No
14/09/10 12:00
>> Admin Login
ENVIRO TECHNOLOGY 01
Admin User:
ID: 00000
14/09/10 12:00
>> Admin Login
ENVIRO TECHNOLOGY 01
Admin User : 00010
Password: 00000
14/09/10 12:00
>> Admin Login

ETS-DSU- G01A01(0202PPCT02) [ver. 1.7T] Page 5
2. DISPLAY MODE
Display Mode is used to select various display formats to display online data. User can use
increment and decrement key to select the display mode. Once display mode is set user can
press “ENT” key to set display mode in EEPROM. To exist this menu press “SEL” Key.
Type: 00000
If display mode is set to Type 00, the unit will display the data from the PID controller, of
which the ID is mentioned under controller Number.
Type: 00001
If display mode is set to Type 01, the unit will display the data from the number of PID
controllers, mentioned under controller Number.
3. CONTROLLER NO:
Same as mentioned under Display mode.
4. PRINT CONTROL
This Parameter function is used for different printer controlling action. Here users first enter
to parameter then scroll Sub-parameter content with the help of INC and DEC Key. If Printer
is not connected then user will get massage “Check Printer” on display, otherwise user get
display Sub-Parameter function. Select sub parameter with the help of increment key and
press Enter key, Pressing enter key twice will show message as “Select Function”. To exist
parameter mode press SEL Key.
ENVIRO TECHNOLOGY 01
Controller No
Print Control
14/09/10 12:00
>> Display Mode
ENVIRO TECHNOLOGY 01
Check Printer
14/09/10 12:00
>> Print Control
ENVIRO TECHNOLOGY 01
No. : 0001
14/09/10 12:00
>> Display Mode

ETS-DSU- G01A01(0202PPCT02) [ver. 1.7T] Page 6
4.1 Set Header Page For Print Start
This function is used to set the page header for printing. Printer Header is printed as a
beginning of the page.
4.2 Cancel Old Printing
This function is used to stop the previous pages under printing. (Normally shall be used if
Print Previous pages command is executed and needs to be cancelled).
4.3 Print Current Reading
This function is used to print the current values of controllers.
“* Printed Current” message will be displayed after activating the parameter.
To identify the print current data transaction “.” Dot will be printed after date and time of the
transaction.
ENVIRO TECHNOLOGY 01
Set Page Header
14/09/10 12:00
>> Print Control
ENVIRO TECHNOLOGY 01
Cancel Old Print
14/09/10 12:00
>> Print Control
ENVIRO TECHNOLOGY 01
Print Current Data
14/09/10 12:00
>> Print Control

ETS-DSU- G01A01(0202PPCT02) [ver. 1.7T] Page 7
4.4 Reset Page No
This function is used to reset Page No to 01.
4.5 Reset Print
This function is used to reset stored print data.
Warning: Please ensure before executing this function as it may result in losing the print data.
This print data can be available with Print Page Command. (PC data will still be available to
user.) “Print Data Deleted” remark and transaction will be stored in unit.
4.6 Reset All Memory.
Caution: This function will reset the memory and hence all process data stored in memory
will be lost, also the print memory can’t available with print page command.
To have ETS-DSU-G01A01(0202PPCT02) MEMORY Reset from ETS-DSU-
G01A01(0202PPCT02) Display unit GOTO “Print Control” and Reset all memory by
selecting “Reset All Memory” Command and press ENTER. “Data will be lost” message will
follow. This is to warn for USER about confirming deleting of all data. If user presses
ENTER all data will be deleted, else not.
ENVIRO TECHNOLOGY 01
Reset Page No
14/09/10 12:00
>> Print Control
ENVIRO TECHNOLOGY 01
Reset Print
14/09/10 12:00
>> Print Control
ENVIRO TECHNOLOGY 01
Reset All Memory
14/09/10 12:00
>> Print Control
ENVIRO TECHNOLOGY 01
Data will be lost
YES
14/09/10 12:00
>> Print Control
NO