Envirogard Hires TORNADO P2 Installation instructions manual

IMPORTANT USER GUIDANCE
TORNADO P2: MINI BOWSER +
PRESSURE WASHER
READ THESE INSTRUCTIONS BEFORE USE
GENERAL: The Tornado P2 is a trolley mounted
pressure washer equipped with a 150 litre water tank,
high-pressure pump, 30 metre reel-mounted high pressure
hose and jetwash lan e. A re oil-start Honda petrol engine
powers the pump - delivering 13 L/min at 2200psi / 150 bar.
The tank an be filled through the lid or by oupling a hose to the refill valve on the side of the
tank. The Tornado is narrow enough to pass through a standard door and may be filled in
advan e before wheeling it to the required lo ation - helpful where there is no water supply.
Envirogard’s hire units ome with a 30m hose - useful where a ess is tight or spa e onstraints
are limiting. A hemi al pi k-up also allows leaning / foaming agents to be added in-line.
PRE-USE CHECKS / FILLING: Visually inspe t the trolley, water
tank, engine, pump, hose, reel and jetwash lan e before use; if
damaged do not use – onta t the supplying hire depot.
Che k the lubri ant level of the gear box, the high pressure pump
and the Honda engine; replenish as ne essary. Ensure there is
petrol in the fuel tank; replenish fuel while the engine is old.
Ensure there is water in the tank before starting the engine – dry-
running will damage the pump. To fill the water tank lo ate the
Mini-Bowser on a level surfa e apable of supporting the
equipments weight - 240kg on e filled. Apply the astor brake;
use wheel ho ks if ground onditions are poor.
Open the water tank and he k the gauze water filter inside the
tank is not blo ked (see image right), then return filter to the tank.
Either onne t a hose to the tank oupling marked “Automati
Fill”, or fill through the tank lid. When the tank is full se ure the lid
losed; the trolley may be wheeled to another lo ation if required.
Unlo k the hose reel, deploy the length of hose required and
onne t the jetwash lan e using the qui k oupling.
OPERATING INSTRUCTIONS:
Rotate engine swit h to “ON” then:
1. Push the fuel lever to “Open”.
2. If this is the first use of the day slide
the hoke lever to “ON”.
3. Pull the re oil to start the engine.
On e running gently return the hoke
lever to the “OFF” position.
4. To flush any air in the system squeeze the jetwash lan e’s
trigger until water flows freely from the nozzle.
5. Set the engine throttle ontrol to “Fast”. The unit is now ready
to begin work.
Page 1 of 4 Ref. EVGD210918

6. Hold the lan e firmly in
bo h hands when squeezing
the trigger -it will “ki k ba k”.
Use only the hose, lan e and
nozzle supplied with the
ma hine; never attempt to
onne t / dis onne t these
while they are pressurised.
If you are not using the lan e
for 5 minutes or more – STOP
the ma hine. The pump will
overheat if it is left to run with
no water passing through it !!!
Spray Pa ern is adjustable from Pinpoint to Fan spray by rotating the lan e nozzle (see above).
Spray Pressure an be adjusted by rotating the Unloader Valve at the high pressure pump; a
gauge on the pump displays the delivered pressure. Pressure an also be adjusted on the
lan e by rotating the nozzle between Pinpoint jet (high pressure) and Fan spray (low pressure).
If you wish to Spray De ergen pla e the
hemi al pi k up pipe in a detergent ontainer
and rotate the lan e nozzle to low pressure;
when you trigger the lan e detergent will now
automati ally be drawn into the system.
You adjust the ratio of detergent-to-water by
rotating the lan e nozzle - towards Fan spray
will in rease the amount of detergent, towards
Pinpoint jet will de rease the amount of
detergent.
To jetwash without detergent simply in rease
the pressure at the spray nozzle, or remove
the pi k-up pipe from the detergent ontainer;
no more detergent will be drawn in and
residue in the line will soon lear.
7. TO STOP: redu e engine speed to idle then turn the engine swit h to “OFF; when the engine
has stopped move the fuel lever to “Closed”. Dissipate any residual pressure in the ma hine by
a tivating the trigger of the jetwash lan e.
Ensure his equipmen is pro ec ed from fros a all imes – emp y he ank and hoses of residual
wa er. S ore in a fros free environmen under cover.
When you have finished with the equipment empty the tank of ALL water – there is a low level
drain in the tank to fa ilitate this. Wind the H.P. hose onto the reel, ensure the hose-reel lo k is
engaged, the jetwash gun is se ure, and the lan e is in its holder. Clean the equipment
thoroughly prior to returning it to the supplying hire depot.
TECHNICAL:
Page 2 of 4 Ref. EVGD210918
DIMENSIONS: Trolley Length 1170mm Width 660mm Height 870mm Ma : Empty 78 kg, Full 228 kg.
ENGINE: Honda GX200 4.1kW Petrol, recoil tart; fuel tank 3.1 litre ; engine oil SAE10W30.
PUMP: Max Flow 13 litre /min @ 150 bar / 2200 p i, pump oil SAE10W30, gearbox oil EP90.
Output : to 30m Jetwa h ho e on reel.

Page 3 of 4 Ref. EVGD210918
CAUTIONS / WARNINGS
IN CASE OF EMERGENCY: TURN THE ENGINE SWITCH TO “OFF” TO STOP MACHINE
PRESS JETWASH TRIGGER TO DISSIPATE RESIDUAL PRESSURE.
IF NOT USING THE TORNADO - STOP THE ENGINE WHEN LEAVING IT UNATTENDED.
Thi equipment i mobile and can be u ed and located in many different environment . U er are
therefore reminded of the need to en ure that all ta k and location are ri k a e ed before activity
commence to en ure that all ignificant hazard are identified with appropriate precaution put in place.
The Tornado Jetwa h i not de igned nor intended for u e in explo ive or flammable atmo phere . The
petrol engine will generate exhau t fume ; the machine hould be located in well-ventilated area where
exhau t fume are able to afely di per e.
Thi equipment i de igned for high pre ure cleaning (150 bar). Thi equipment eject water at high
velocity and water jet are dangerou if mi u ed. The jet/ pray mu t not be directed at people, animal ,
the machine it elf, non-waterproof, fragile or electrical equipment, nor power cable . Do not attempt to
couple or un-couple tool , ho e or nozzle while the equipment i pre uri ed.
The equipment hould be operated by an able bodied adult competent in the u e of pre ure wa her up
to 150 bar / 2200p i. Thi equipment mu t not be u ed by minor or anybody under the influence of drug
or alcohol. The work area hould be demarcated and exclude other people from the jetwa h pray zone.
Per onal protective clothing mu t be worn. When operating the Tornado u e an impact re i tant vi or or
goggle and ear defender a a minimum. Water jet can generate high noi e level and produce a high
impact force, o when u ing the jetwa h protective (waterproof) clothing, glove and boot hould be
worn in addition. Some jetwa h application may generate an aero ol containing pathogen e.g. guano
removal, the cleaning of animal by product etc; the u er mu t a e whether RPE need to be u ed in
thi ituation.
The engine and pump generate noi e and the level varie according to engine peed; the equipment ha a
Guaranteed Sound Power of LWAd 84dB. The jetwa h lance i upplied with a 30 metre ho e o where
po ible locate the machine away from the cleaning activity and per on who might be affected by the
noi e. Per onnel obliged to work in clo e proximity to the machine mu t u e hearing protection. If the
machine i operating in a wholly or partially enclo ed pace from which noi e cannot readily di ipate
U er hould con ider conducting a noi e urvey to identify if extended mandatory hearing protection
zone are required.
Thi equipment contain water - do not allow it to freeze !!! If the pump ha frozen DO NOT attempt to
tart the engine; allow to thaw and in pect for damage before u e. If po ible tore indoor during fro t;
if thi i not po ible you mu t introduce anti-freeze (25% olution) via the tank; operate the engine at low
peed to draw it through the pump, ho e , lance and pray nozzle : thi will protect down to approx – 5°C.
Before next u e flu h with clean water and collect the antifreeze olution for re-u e (do not di po e of
antifreeze to the environment).
Legionella bacteria can grow at temperature between 20°C and 45°C, particularly in dirty or
contaminated water. For thi rea on alway fill the bow er with cold, clean, potable (drinking quality)
water only. If you will not be u ing the equipment for a few day drain the equipment of water. Before u e
alway purge the equipment u ing clean water, operating the engine at low peed to minimi e production
of pray.
If ambient condition are uch that water temperature i u tained above 20°C con ider treating the tank
and flu hing the equipment periodically with a aniti ing agent uch a Milton. The u er’ attention i
drawn to HSE’ guidance on Legionella ACoP L8; depending on your work environment and prevailing
temperature it may be nece ary for you to include the equipment within your Legionella management
programme.
Fuel & Lubricant: petrol i flammable – take care not to cau e a fire - top up fuel and check lubricant
level with the machine hut down and in a cold tate. Lubricant level hould be checked DAILY.
Ensure his equipmen is pro ec ed from fros a all imes – emp y he ank and hoses
of residual wa er. S ore in a fros free environmen under cover.
Clean he equipmen horoughly prior o re urning i o he supplying hire depo .
Equipmen re urned in a dir y or con amina ed condi ion may be refused and will be charged.

TROUBLE SHOOTING GUIDE:
FOR MORE INFORMATION ABOUT OUR RANGE OF HIRE EQUIPMENT P EASE SEE OUR WEBSITE www.envirogard.co.uk
Page 4 of 4 Ref. EVGD210918