Envoy Connect User manual
Press in the lower middle of the
keypad for 2 seconds to turn the
CONNECT on. The LED will turn on, a
chime will sound, the preview* of the last
Publication is played and it then enters
Pause Mode.
Press again for 2 seconds to turn the
player off (a different chime will sound
and the LED will turn off).
*A Publication is previewed by playing
the rst audio le in it, or the rst 10
seconds thereof, whichever is shorter.
Previews are also played when browsing
through the Publications using while
in Pause Mode.
While the CONNECT is paused,
a click on the Bookshelf button will
preview the current Publication. An
additional click will preview the next
Publication. Once the last one has been
previewed, it will return to preview the
rst.
Click to select a Publication for
listening.
*The Bookshelf button is only active
during Pause Mode.
Use to control the Sleep Timer
function. Each click will sound a different
chime and change the setting as follows:
15 minutes > 30 minutes >
60 minutes > OFF
A 2-second press on will turn the
Sleep Timer off, regardless of the current
setting.
Once set, when the Sleep Timer expires,
a bookmark will be saved and the
CONNECT will turn off silently.
*The Sleep Timer may only be set while in
Pause Mode.
**When the sleep timer is activated,
the LED will blink intermittently during
playback.
*CONNECT saves a bookmark for each
Publication separately.
During continuous press, the CONNECT
will beep each time it skips and the LED
will blink.
*Actual time may vary.
***If CONNECT is turned off before
the timer expires, the sleep timer
is automatically reset to off when
CONNECT restarts.
SOLAR AUDIO PLAYER USER MANUAL
ENVOY
CONNECT
TURNING CONNECT
ON/OFF
SELECTING A
PUBLICATION FOR
PLAYBACK
SLEEP TIMER
Each Publication (book, magazine, etc.)
is subdivided into one or more Sections
(chapters or audio les).
During playback, click or to
jump backward or forward one Section
within the current Publication. If the last
Section is currently playing, a chime will
be played to indicate end of Publication.
If the rst Section is playing, it will restart
from the beginning.
A 2-second press will skip approximately
25 seconds* within the current Section.
A continuous press will continue
skipping until the button is released
or the beginning/end of the Section is
reached.
While in playback, click to
pause playback. The LED will blink
intermittently. To resume, click again.
*If CONNECT is left paused for 5 minutes,
it will automatically turn off.
Bookmarking on the CONNECT is
completely automatic. Whenever paused,
or turned off, CONNECT will bookmark
the current Publication and the current
position within that Publication (minus 3
seconds).
NAVIGATING
DURING PLAYBACK
PAUSING/
BOOKMARKING
When the end of a Publication is
reached, the bookmark is automatically
reset to the beginning of that
Publication.
To manually reset to the beginning of a
Publication, during playback click the
button repetitively until the beginning
of the rst Section is reached. The
bookmark will be saved from that point.
RESETTING A
BOOKMARK TO
THE BEGINNING
While in Pause Mode, a 5-second
continuous press on will delete the
current Publication. Five distinct beeps
will be played to warn the user of the
pending deletion.
Once the publication is deleted, a chime
will be played as conrmation and the
CONNECT will skip to the next available
Publication, preview it and pause.
*Deleting a publication may only be done
while in Pause Mode.
After pausing the CONNECT, press and
hold the and buttons together.
The following occurs:
• The serial number is voiced in
Mandarin (internal QA feature).
• All bookmarks are erased!
• The volume is reset to medium.
• The player is turned off.
*Caution should be exercised when using
this function since all bookmarks will be
erased!
**Erasing all bookmarks resets playback
to the beginning of the rst Publication.
DELETING A
PUBLICATION
RESETTING THE
CONNECT
Press and hold until the LED lights
and a chime sounds. The CONNECT will
turn on, preview the rst Publication (or
the last one played) and then pause.
or
EASY START
1 2 3 4
56789
1/3
Envoy Connect User Manual - A4 - English - 2020.01.15-1.1.2
Press in the lower middle of the
keypad for 2 seconds to turn the
CONNECT on. The LED will turn on, a
chime will sound, the preview* of the last
Publication is played and it then enters
Pause Mode.
Press again for 2 seconds to turn the
player off (a different chime will sound
and the LED will turn off).
*A Publication is previewed by playing
the rst audio le in it, or the rst 10
seconds thereof, whichever is shorter.
Previews are also played when browsing
through the Publications using while
in Pause Mode.
While the CONNECT is paused,
a click on the Bookshelf button will
preview the current Publication. An
additional click will preview the next
Publication. Once the last one has been
previewed, it will return to preview the
rst.
Click to select a Publication for
listening.
*The Bookshelf button is only active
during Pause Mode.
Use to control the Sleep Timer
function. Each click will sound a different
chime and change the setting as follows:
15 minutes > 30 minutes >
60 minutes > OFF
A 2-second press on will turn the
Sleep Timer off, regardless of the current
setting.
Once set, when the Sleep Timer expires,
a bookmark will be saved and the
CONNECT will turn off silently.
*The Sleep Timer may only be set while in
Pause Mode.
**When the sleep timer is activated,
the LED will blink intermittently during
playback.
*CONNECT saves a bookmark for each
Publication separately.
During continuous press, the CONNECT
will beep each time it skips and the LED
will blink.
*Actual time may vary.
***If CONNECT is turned off before
the timer expires, the sleep timer
is automatically reset to off when
CONNECT restarts.
SOLAR AUDIO PLAYER USER MANUAL
ENVOY
CONNECT
TURNING CONNECT
ON/OFF
SELECTING A
PUBLICATION FOR
PLAYBACK
SLEEP TIMER
Each Publication (book, magazine, etc.)
is subdivided into one or more Sections
(chapters or audio les).
During playback, click or to
jump backward or forward one Section
within the current Publication. If the last
Section is currently playing, a chime will
be played to indicate end of Publication.
If the rst Section is playing, it will restart
from the beginning.
A 2-second press will skip approximately
25 seconds* within the current Section.
A continuous press will continue
skipping until the button is released
or the beginning/end of the Section is
reached.
While in playback, click to
pause playback. The LED will blink
intermittently. To resume, click again.
*If CONNECT is left paused for 5 minutes,
it will automatically turn off.
Bookmarking on the CONNECT is
completely automatic. Whenever paused,
or turned off, CONNECT will bookmark
the current Publication and the current
position within that Publication (minus 3
seconds).
NAVIGATING
DURING PLAYBACK
PAUSING/
BOOKMARKING
When the end of a Publication is
reached, the bookmark is automatically
reset to the beginning of that
Publication.
To manually reset to the beginning of a
Publication, during playback click the
button repetitively until the beginning
of the rst Section is reached. The
bookmark will be saved from that point.
RESETTING A
BOOKMARK TO
THE BEGINNING
While in Pause Mode, a 5-second
continuous press on will delete the
current Publication. Five distinct beeps
will be played to warn the user of the
pending deletion.
Once the publication is deleted, a chime
will be played as conrmation and the
CONNECT will skip to the next available
Publication, preview it and pause.
*Deleting a publication may only be done
while in Pause Mode.
After pausing the CONNECT, press and
hold the and buttons together.
The following occurs:
• The serial number is voiced in
Mandarin (internal QA feature).
• All bookmarks are erased!
• The volume is reset to medium.
• The player is turned off.
*Caution should be exercised when using
this function since all bookmarks will be
erased!
**Erasing all bookmarks resets playback
to the beginning of the rst Publication.
DELETING A
PUBLICATION
RESETTING THE
CONNECT
Press and hold until the LED lights
and a chime sounds. The CONNECT will
turn on, preview the rst Publication (or
the last one played) and then pause.
or
EASY START
1 2 3 4
56789
1/3
Envoy Connect User Manual - A4 - English - 2020.01.15-1.1.2
Press in the lower middle of the
keypad for 2 seconds to turn the
CONNECT on. The LED will turn on, a
chime will sound, the preview* of the last
Publication is played and it then enters
Pause Mode.
Press again for 2 seconds to turn the
player off (a different chime will sound
and the LED will turn off).
*A Publication is previewed by playing
the rst audio le in it, or the rst 10
seconds thereof, whichever is shorter.
Previews are also played when browsing
through the Publications using while
in Pause Mode.
While the CONNECT is paused,
a click on the Bookshelf button will
preview the current Publication. An
additional click will preview the next
Publication. Once the last one has been
previewed, it will return to preview the
rst.
Click to select a Publication for
listening.
*The Bookshelf button is only active
during Pause Mode.
Use to control the Sleep Timer
function. Each click will sound a different
chime and change the setting as follows:
15 minutes > 30 minutes >
60 minutes > OFF
A 2-second press on will turn the
Sleep Timer off, regardless of the current
setting.
Once set, when the Sleep Timer expires,
a bookmark will be saved and the
CONNECT will turn off silently.
*The Sleep Timer may only be set while in
Pause Mode.
**When the sleep timer is activated,
the LED will blink intermittently during
playback.
*CONNECT saves a bookmark for each
Publication separately.
During continuous press, the CONNECT
will beep each time it skips and the LED
will blink.
*Actual time may vary.
***If CONNECT is turned off before
the timer expires, the sleep timer
is automatically reset to off when
CONNECT restarts.
SOLAR AUDIO PLAYER USER MANUAL
ENVOY
CONNECT
TURNING CONNECT
ON/OFF
SELECTING A
PUBLICATION FOR
PLAYBACK
SLEEP TIMER
Each Publication (book, magazine, etc.)
is subdivided into one or more Sections
(chapters or audio les).
During playback, click or to
jump backward or forward one Section
within the current Publication. If the last
Section is currently playing, a chime will
be played to indicate end of Publication.
If the rst Section is playing, it will restart
from the beginning.
A 2-second press will skip approximately
25 seconds* within the current Section.
A continuous press will continue
skipping until the button is released
or the beginning/end of the Section is
reached.
While in playback, click to
pause playback. The LED will blink
intermittently. To resume, click again.
*If CONNECT is left paused for 5 minutes,
it will automatically turn off.
Bookmarking on the CONNECT is
completely automatic. Whenever paused,
or turned off, CONNECT will bookmark
the current Publication and the current
position within that Publication (minus 3
seconds).
NAVIGATING
DURING PLAYBACK
PAUSING/
BOOKMARKING
When the end of a Publication is
reached, the bookmark is automatically
reset to the beginning of that
Publication.
To manually reset to the beginning of a
Publication, during playback click the
button repetitively until the beginning
of the rst Section is reached. The
bookmark will be saved from that point.
RESETTING A
BOOKMARK TO
THE BEGINNING
While in Pause Mode, a 5-second
continuous press on will delete the
current Publication. Five distinct beeps
will be played to warn the user of the
pending deletion.
Once the publication is deleted, a chime
will be played as conrmation and the
CONNECT will skip to the next available
Publication, preview it and pause.
*Deleting a publication may only be done
while in Pause Mode.
After pausing the CONNECT, press and
hold the and buttons together.
The following occurs:
• The serial number is voiced in
Mandarin (internal QA feature).
• All bookmarks are erased!
• The volume is reset to medium.
• The player is turned off.
*Caution should be exercised when using
this function since all bookmarks will be
erased!
**Erasing all bookmarks resets playback
to the beginning of the rst Publication.
DELETING A
PUBLICATION
RESETTING THE
CONNECT
Press and hold until the LED lights
and a chime sounds. The CONNECT will
turn on, preview the rst Publication (or
the last one played) and then pause.
or
EASY START
1 2 3 4
56789
1/3
Envoy Connect User Manual - A4 - English - 2020.01.15-1.1.2
Press in the lower middle of the
keypad for 2 seconds to turn the
CONNECT on. The LED will turn on, a
chime will sound, the preview* of the last
Publication is played and it then enters
Pause Mode.
Press again for 2 seconds to turn the
player off (a different chime will sound
and the LED will turn off).
*A Publication is previewed by playing
the rst audio le in it, or the rst 10
seconds thereof, whichever is shorter.
Previews are also played when browsing
through the Publications using while
in Pause Mode.
While the CONNECT is paused,
a click on the Bookshelf button will
preview the current Publication. An
additional click will preview the next
Publication. Once the last one has been
previewed, it will return to preview the
rst.
Click to select a Publication for
listening.
*The Bookshelf button is only active
during Pause Mode.
Use to control the Sleep Timer
function. Each click will sound a different
chime and change the setting as follows:
15 minutes > 30 minutes >
60 minutes > OFF
A 2-second press on will turn the
Sleep Timer off, regardless of the current
setting.
Once set, when the Sleep Timer expires,
a bookmark will be saved and the
CONNECT will turn off silently.
*The Sleep Timer may only be set while in
Pause Mode.
**When the sleep timer is activated,
the LED will blink intermittently during
playback.
*CONNECT saves a bookmark for each
Publication separately.
During continuous press, the CONNECT
will beep each time it skips and the LED
will blink.
*Actual time may vary.
***If CONNECT is turned off before
the timer expires, the sleep timer
is automatically reset to off when
CONNECT restarts.
SOLAR AUDIO PLAYER USER MANUAL
ENVOY
CONNECT
TURNING CONNECT
ON/OFF
SELECTING A
PUBLICATION FOR
PLAYBACK
SLEEP TIMER
Each Publication (book, magazine, etc.)
is subdivided into one or more Sections
(chapters or audio les).
During playback, click or to
jump backward or forward one Section
within the current Publication. If the last
Section is currently playing, a chime will
be played to indicate end of Publication.
If the rst Section is playing, it will restart
from the beginning.
A 2-second press will skip approximately
25 seconds* within the current Section.
A continuous press will continue
skipping until the button is released
or the beginning/end of the Section is
reached.
While in playback, click to
pause playback. The LED will blink
intermittently. To resume, click again.
*If CONNECT is left paused for 5 minutes,
it will automatically turn off.
Bookmarking on the CONNECT is
completely automatic. Whenever paused,
or turned off, CONNECT will bookmark
the current Publication and the current
position within that Publication (minus 3
seconds).
NAVIGATING
DURING PLAYBACK
PAUSING/
BOOKMARKING
When the end of a Publication is
reached, the bookmark is automatically
reset to the beginning of that
Publication.
To manually reset to the beginning of a
Publication, during playback click the
button repetitively until the beginning
of the rst Section is reached. The
bookmark will be saved from that point.
RESETTING A
BOOKMARK TO
THE BEGINNING
While in Pause Mode, a 5-second
continuous press on will delete the
current Publication. Five distinct beeps
will be played to warn the user of the
pending deletion.
Once the publication is deleted, a chime
will be played as conrmation and the
CONNECT will skip to the next available
Publication, preview it and pause.
*Deleting a publication may only be done
while in Pause Mode.
After pausing the CONNECT, press and
hold the and buttons together.
The following occurs:
• The serial number is voiced in
Mandarin (internal QA feature).
• All bookmarks are erased!
• The volume is reset to medium.
• The player is turned off.
*Caution should be exercised when using
this function since all bookmarks will be
erased!
**Erasing all bookmarks resets playback
to the beginning of the rst Publication.
DELETING A
PUBLICATION
RESETTING THE
CONNECT
Press and hold until the LED lights
and a chime sounds. The CONNECT will
turn on, preview the rst Publication (or
the last one played) and then pause.
or
EASY START
1 2 3 4
56789
1/3
Envoy Connect User Manual - A4 - English - 2020.01.15-1.1.2
Press in the lower middle of the
keypad for 2 seconds to turn the
CONNECT on. The LED will turn on, a
chime will sound, the preview* of the last
Publication is played and it then enters
Pause Mode.
Press again for 2 seconds to turn the
player off (a different chime will sound
and the LED will turn off).
*A Publication is previewed by playing
the rst audio le in it, or the rst 10
seconds thereof, whichever is shorter.
Previews are also played when browsing
through the Publications using while
in Pause Mode.
While the CONNECT is paused,
a click on the Bookshelf button will
preview the current Publication. An
additional click will preview the next
Publication. Once the last one has been
previewed, it will return to preview the
rst.
Click to select a Publication for
listening.
*The Bookshelf button is only active
during Pause Mode.
Use to control the Sleep Timer
function. Each click will sound a different
chime and change the setting as follows:
15 minutes > 30 minutes >
60 minutes > OFF
A 2-second press on will turn the
Sleep Timer off, regardless of the current
setting.
Once set, when the Sleep Timer expires,
a bookmark will be saved and the
CONNECT will turn off silently.
*The Sleep Timer may only be set while in
Pause Mode.
**When the sleep timer is activated,
the LED will blink intermittently during
playback.
*CONNECT saves a bookmark for each
Publication separately.
During continuous press, the CONNECT
will beep each time it skips and the LED
will blink.
*Actual time may vary.
***If CONNECT is turned off before
the timer expires, the sleep timer
is automatically reset to off when
CONNECT restarts.
SOLAR AUDIO PLAYER USER MANUAL
ENVOY
CONNECT
TURNING CONNECT
ON/OFF
SELECTING A
PUBLICATION FOR
PLAYBACK
SLEEP TIMER
Each Publication (book, magazine, etc.)
is subdivided into one or more Sections
(chapters or audio les).
During playback, click or to
jump backward or forward one Section
within the current Publication. If the last
Section is currently playing, a chime will
be played to indicate end of Publication.
If the rst Section is playing, it will restart
from the beginning.
A 2-second press will skip approximately
25 seconds* within the current Section.
A continuous press will continue
skipping until the button is released
or the beginning/end of the Section is
reached.
While in playback, click to
pause playback. The LED will blink
intermittently. To resume, click again.
*If CONNECT is left paused for 5 minutes,
it will automatically turn off.
Bookmarking on the CONNECT is
completely automatic. Whenever paused,
or turned off, CONNECT will bookmark
the current Publication and the current
position within that Publication (minus 3
seconds).
NAVIGATING
DURING PLAYBACK
PAUSING/
BOOKMARKING
When the end of a Publication is
reached, the bookmark is automatically
reset to the beginning of that
Publication.
To manually reset to the beginning of a
Publication, during playback click the
button repetitively until the beginning
of the rst Section is reached. The
bookmark will be saved from that point.
RESETTING A
BOOKMARK TO
THE BEGINNING
While in Pause Mode, a 5-second
continuous press on will delete the
current Publication. Five distinct beeps
will be played to warn the user of the
pending deletion.
Once the publication is deleted, a chime
will be played as conrmation and the
CONNECT will skip to the next available
Publication, preview it and pause.
*Deleting a publication may only be done
while in Pause Mode.
After pausing the CONNECT, press and
hold the and buttons together.
The following occurs:
• The serial number is voiced in
Mandarin (internal QA feature).
• All bookmarks are erased!
• The volume is reset to medium.
• The player is turned off.
*Caution should be exercised when using
this function since all bookmarks will be
erased!
**Erasing all bookmarks resets playback
to the beginning of the rst Publication.
DELETING A
PUBLICATION
RESETTING THE
CONNECT
Press and hold until the LED lights
and a chime sounds. The CONNECT will
turn on, preview the rst Publication (or
the last one played) and then pause.
or
EASY START
1 2 3 4
56789
1/3
Envoy Connect User Manual - A4 - English - 2020.01.15-1.1.2
Press in the lower middle of the
keypad for 2 seconds to turn the
CONNECT on. The LED will turn on, a
chime will sound, the preview* of the last
Publication is played and it then enters
Pause Mode.
Press again for 2 seconds to turn the
player off (a different chime will sound
and the LED will turn off).
*A Publication is previewed by playing
the rst audio le in it, or the rst 10
seconds thereof, whichever is shorter.
Previews are also played when browsing
through the Publications using while
in Pause Mode.
While the CONNECT is paused,
a click on the Bookshelf button will
preview the current Publication. An
additional click will preview the next
Publication. Once the last one has been
previewed, it will return to preview the
rst.
Click to select a Publication for
listening.
*The Bookshelf button is only active
during Pause Mode.
Use to control the Sleep Timer
function. Each click will sound a different
chime and change the setting as follows:
15 minutes > 30 minutes >
60 minutes > OFF
A 2-second press on will turn the
Sleep Timer off, regardless of the current
setting.
Once set, when the Sleep Timer expires,
a bookmark will be saved and the
CONNECT will turn off silently.
*The Sleep Timer may only be set while in
Pause Mode.
**When the sleep timer is activated,
the LED will blink intermittently during
playback.
*CONNECT saves a bookmark for each
Publication separately.
During continuous press, the CONNECT
will beep each time it skips and the LED
will blink.
*Actual time may vary.
***If CONNECT is turned off before
the timer expires, the sleep timer
is automatically reset to off when
CONNECT restarts.
SOLAR AUDIO PLAYER USER MANUAL
ENVOY
CONNECT
TURNING CONNECT
ON/OFF
SELECTING A
PUBLICATION FOR
PLAYBACK
SLEEP TIMER
Each Publication (book, magazine, etc.)
is subdivided into one or more Sections
(chapters or audio les).
During playback, click or to
jump backward or forward one Section
within the current Publication. If the last
Section is currently playing, a chime will
be played to indicate end of Publication.
If the rst Section is playing, it will restart
from the beginning.
A 2-second press will skip approximately
25 seconds* within the current Section.
A continuous press will continue
skipping until the button is released
or the beginning/end of the Section is
reached.
While in playback, click to
pause playback. The LED will blink
intermittently. To resume, click again.
*If CONNECT is left paused for 5 minutes,
it will automatically turn off.
Bookmarking on the CONNECT is
completely automatic. Whenever paused,
or turned off, CONNECT will bookmark
the current Publication and the current
position within that Publication (minus 3
seconds).
NAVIGATING
DURING PLAYBACK
PAUSING/
BOOKMARKING
When the end of a Publication is
reached, the bookmark is automatically
reset to the beginning of that
Publication.
To manually reset to the beginning of a
Publication, during playback click the
button repetitively until the beginning
of the rst Section is reached. The
bookmark will be saved from that point.
RESETTING A
BOOKMARK TO
THE BEGINNING
While in Pause Mode, a 5-second
continuous press on will delete the
current Publication. Five distinct beeps
will be played to warn the user of the
pending deletion.
Once the publication is deleted, a chime
will be played as conrmation and the
CONNECT will skip to the next available
Publication, preview it and pause.
*Deleting a publication may only be done
while in Pause Mode.
After pausing the CONNECT, press and
hold the and buttons together.
The following occurs:
• The serial number is voiced in
Mandarin (internal QA feature).
• All bookmarks are erased!
• The volume is reset to medium.
• The player is turned off.
*Caution should be exercised when using
this function since all bookmarks will be
erased!
**Erasing all bookmarks resets playback
to the beginning of the rst Publication.
DELETING A
PUBLICATION
RESETTING THE
CONNECT
Press and hold until the LED lights
and a chime sounds. The CONNECT will
turn on, preview the rst Publication (or
the last one played) and then pause.
or
EASY START
1 2 3 4
56789
1/3
Envoy Connect User Manual - A4 - English - 2020.01.15-1.1.2
Press in the lower middle of the
keypad for 2 seconds to turn the
CONNECT on. The LED will turn on, a
chime will sound, the preview* of the last
Publication is played and it then enters
Pause Mode.
Press again for 2 seconds to turn the
player off (a different chime will sound
and the LED will turn off).
*A Publication is previewed by playing
the rst audio le in it, or the rst 10
seconds thereof, whichever is shorter.
Previews are also played when browsing
through the Publications using while
in Pause Mode.
While the CONNECT is paused,
a click on the Bookshelf button will
preview the current Publication. An
additional click will preview the next
Publication. Once the last one has been
previewed, it will return to preview the
rst.
Click to select a Publication for
listening.
*The Bookshelf button is only active
during Pause Mode.
Use to control the Sleep Timer
function. Each click will sound a different
chime and change the setting as follows:
15 minutes > 30 minutes >
60 minutes > OFF
A 2-second press on will turn the
Sleep Timer off, regardless of the current
setting.
Once set, when the Sleep Timer expires,
a bookmark will be saved and the
CONNECT will turn off silently.
*The Sleep Timer may only be set while in
Pause Mode.
**When the sleep timer is activated,
the LED will blink intermittently during
playback.
*CONNECT saves a bookmark for each
Publication separately.
During continuous press, the CONNECT
will beep each time it skips and the LED
will blink.
*Actual time may vary.
***If CONNECT is turned off before
the timer expires, the sleep timer
is automatically reset to off when
CONNECT restarts.
SOLAR AUDIO PLAYER USER MANUAL
ENVOY
CONNECT
TURNING CONNECT
ON/OFF
SELECTING A
PUBLICATION FOR
PLAYBACK
SLEEP TIMER
Each Publication (book, magazine, etc.)
is subdivided into one or more Sections
(chapters or audio les).
During playback, click or to
jump backward or forward one Section
within the current Publication. If the last
Section is currently playing, a chime will
be played to indicate end of Publication.
If the rst Section is playing, it will restart
from the beginning.
A 2-second press will skip approximately
25 seconds* within the current Section.
A continuous press will continue
skipping until the button is released
or the beginning/end of the Section is
reached.
While in playback, click to
pause playback. The LED will blink
intermittently. To resume, click again.
*If CONNECT is left paused for 5 minutes,
it will automatically turn off.
Bookmarking on the CONNECT is
completely automatic. Whenever paused,
or turned off, CONNECT will bookmark
the current Publication and the current
position within that Publication (minus 3
seconds).
NAVIGATING
DURING PLAYBACK
PAUSING/
BOOKMARKING
When the end of a Publication is
reached, the bookmark is automatically
reset to the beginning of that
Publication.
To manually reset to the beginning of a
Publication, during playback click the
button repetitively until the beginning
of the rst Section is reached. The
bookmark will be saved from that point.
RESETTING A
BOOKMARK TO
THE BEGINNING
While in Pause Mode, a 5-second
continuous press on will delete the
current Publication. Five distinct beeps
will be played to warn the user of the
pending deletion.
Once the publication is deleted, a chime
will be played as conrmation and the
CONNECT will skip to the next available
Publication, preview it and pause.
*Deleting a publication may only be done
while in Pause Mode.
After pausing the CONNECT, press and
hold the and buttons together.
The following occurs:
• The serial number is voiced in
Mandarin (internal QA feature).
• All bookmarks are erased!
• The volume is reset to medium.
• The player is turned off.
*Caution should be exercised when using
this function since all bookmarks will be
erased!
**Erasing all bookmarks resets playback
to the beginning of the rst Publication.
DELETING A
PUBLICATION
RESETTING THE
CONNECT
Press and hold until the LED lights
and a chime sounds. The CONNECT will
turn on, preview the rst Publication (or
the last one played) and then pause.
or
EASY START
1 2 3 4
56789
1/3
Envoy Connect User Manual - A4 - English - 2020.01.15-1.1.2
Press in the lower middle of the
keypad for 2 seconds to turn the
CONNECT on. The LED will turn on, a
chime will sound, the preview* of the last
Publication is played and it then enters
Pause Mode.
Press again for 2 seconds to turn the
player off (a different chime will sound
and the LED will turn off).
*A Publication is previewed by playing
the rst audio le in it, or the rst 10
seconds thereof, whichever is shorter.
Previews are also played when browsing
through the Publications using while
in Pause Mode.
While the CONNECT is paused,
a click on the Bookshelf button will
preview the current Publication. An
additional click will preview the next
Publication. Once the last one has been
previewed, it will return to preview the
rst.
Click to select a Publication for
listening.
*The Bookshelf button is only active
during Pause Mode.
Use to control the Sleep Timer
function. Each click will sound a different
chime and change the setting as follows:
15 minutes > 30 minutes >
60 minutes > OFF
A 2-second press on will turn the
Sleep Timer off, regardless of the current
setting.
Once set, when the Sleep Timer expires,
a bookmark will be saved and the
CONNECT will turn off silently.
*The Sleep Timer may only be set while in
Pause Mode.
**When the sleep timer is activated,
the LED will blink intermittently during
playback.
*CONNECT saves a bookmark for each
Publication separately.
During continuous press, the CONNECT
will beep each time it skips and the LED
will blink.
*Actual time may vary.
***If CONNECT is turned off before
the timer expires, the sleep timer
is automatically reset to off when
CONNECT restarts.
SOLAR AUDIO PLAYER USER MANUAL
ENVOY
CONNECT
TURNING CONNECT
ON/OFF
SELECTING A
PUBLICATION FOR
PLAYBACK
SLEEP TIMER
Each Publication (book, magazine, etc.)
is subdivided into one or more Sections
(chapters or audio les).
During playback, click or to
jump backward or forward one Section
within the current Publication. If the last
Section is currently playing, a chime will
be played to indicate end of Publication.
If the rst Section is playing, it will restart
from the beginning.
A 2-second press will skip approximately
25 seconds* within the current Section.
A continuous press will continue
skipping until the button is released
or the beginning/end of the Section is
reached.
While in playback, click to
pause playback. The LED will blink
intermittently. To resume, click again.
*If CONNECT is left paused for 5 minutes,
it will automatically turn off.
Bookmarking on the CONNECT is
completely automatic. Whenever paused,
or turned off, CONNECT will bookmark
the current Publication and the current
position within that Publication (minus 3
seconds).
NAVIGATING
DURING PLAYBACK
PAUSING/
BOOKMARKING
When the end of a Publication is
reached, the bookmark is automatically
reset to the beginning of that
Publication.
To manually reset to the beginning of a
Publication, during playback click the
button repetitively until the beginning
of the rst Section is reached. The
bookmark will be saved from that point.
RESETTING A
BOOKMARK TO
THE BEGINNING
While in Pause Mode, a 5-second
continuous press on will delete the
current Publication. Five distinct beeps
will be played to warn the user of the
pending deletion.
Once the publication is deleted, a chime
will be played as conrmation and the
CONNECT will skip to the next available
Publication, preview it and pause.
*Deleting a publication may only be done
while in Pause Mode.
After pausing the CONNECT, press and
hold the and buttons together.
The following occurs:
• The serial number is voiced in
Mandarin (internal QA feature).
• All bookmarks are erased!
• The volume is reset to medium.
• The player is turned off.
*Caution should be exercised when using
this function since all bookmarks will be
erased!
**Erasing all bookmarks resets playback
to the beginning of the rst Publication.
DELETING A
PUBLICATION
RESETTING THE
CONNECT
Press and hold until the LED lights
and a chime sounds. The CONNECT will
turn on, preview the rst Publication (or
the last one played) and then pause.
or
EASY START
1 2 3 4
56789
1/3
Envoy Connect User Manual - A4 - English - 2020.01.15-1.1.2
Press in the lower middle of the
keypad for 2 seconds to turn the
CONNECT on. The LED will turn on, a
chime will sound, the preview* of the last
Publication is played and it then enters
Pause Mode.
Press again for 2 seconds to turn the
player off (a different chime will sound
and the LED will turn off).
*A Publication is previewed by playing
the rst audio le in it, or the rst 10
seconds thereof, whichever is shorter.
Previews are also played when browsing
through the Publications using while
in Pause Mode.
While the CONNECT is paused,
a click on the Bookshelf button will
preview the current Publication. An
additional click will preview the next
Publication. Once the last one has been
previewed, it will return to preview the
rst.
Click to select a Publication for
listening.
*The Bookshelf button is only active
during Pause Mode.
Use to control the Sleep Timer
function. Each click will sound a different
chime and change the setting as follows:
15 minutes > 30 minutes >
60 minutes > OFF
A 2-second press on will turn the
Sleep Timer off, regardless of the current
setting.
Once set, when the Sleep Timer expires,
a bookmark will be saved and the
CONNECT will turn off silently.
*The Sleep Timer may only be set while in
Pause Mode.
**When the sleep timer is activated,
the LED will blink intermittently during
playback.
*CONNECT saves a bookmark for each
Publication separately.
During continuous press, the CONNECT
will beep each time it skips and the LED
will blink.
*Actual time may vary.
***If CONNECT is turned off before
the timer expires, the sleep timer
is automatically reset to off when
CONNECT restarts.
SOLAR AUDIO PLAYER USER MANUAL
ENVOY
CONNECT
TURNING CONNECT
ON/OFF
SELECTING A
PUBLICATION FOR
PLAYBACK
SLEEP TIMER
Each Publication (book, magazine, etc.)
is subdivided into one or more Sections
(chapters or audio les).
During playback, click or to
jump backward or forward one Section
within the current Publication. If the last
Section is currently playing, a chime will
be played to indicate end of Publication.
If the rst Section is playing, it will restart
from the beginning.
A 2-second press will skip approximately
25 seconds* within the current Section.
A continuous press will continue
skipping until the button is released
or the beginning/end of the Section is
reached.
While in playback, click to
pause playback. The LED will blink
intermittently. To resume, click again.
*If CONNECT is left paused for 5 minutes,
it will automatically turn off.
Bookmarking on the CONNECT is
completely automatic. Whenever paused,
or turned off, CONNECT will bookmark
the current Publication and the current
position within that Publication (minus 3
seconds).
NAVIGATING
DURING PLAYBACK
PAUSING/
BOOKMARKING
When the end of a Publication is
reached, the bookmark is automatically
reset to the beginning of that
Publication.
To manually reset to the beginning of a
Publication, during playback click the
button repetitively until the beginning
of the rst Section is reached. The
bookmark will be saved from that point.
RESETTING A
BOOKMARK TO
THE BEGINNING
While in Pause Mode, a 5-second
continuous press on will delete the
current Publication. Five distinct beeps
will be played to warn the user of the
pending deletion.
Once the publication is deleted, a chime
will be played as conrmation and the
CONNECT will skip to the next available
Publication, preview it and pause.
*Deleting a publication may only be done
while in Pause Mode.
After pausing the CONNECT, press and
hold the and buttons together.
The following occurs:
• The serial number is voiced in
Mandarin (internal QA feature).
• All bookmarks are erased!
• The volume is reset to medium.
• The player is turned off.
*Caution should be exercised when using
this function since all bookmarks will be
erased!
**Erasing all bookmarks resets playback
to the beginning of the rst Publication.
DELETING A
PUBLICATION
RESETTING THE
CONNECT
Press and hold until the LED lights
and a chime sounds. The CONNECT will
turn on, preview the rst Publication (or
the last one played) and then pause.
or
EASY START
1 2 3 4
56789
1/3
Envoy Connect User Manual - A4 - English - 2020.01.15-1.1.2
Press in the lower middle of the
keypad for 2 seconds to turn the
CONNECT on. The LED will turn on, a
chime will sound, the preview* of the last
Publication is played and it then enters
Pause Mode.
Press again for 2 seconds to turn the
player off (a different chime will sound
and the LED will turn off).
*A Publication is previewed by playing
the rst audio le in it, or the rst 10
seconds thereof, whichever is shorter.
Previews are also played when browsing
through the Publications using while
in Pause Mode.
While the CONNECT is paused,
a click on the Bookshelf button will
preview the current Publication. An
additional click will preview the next
Publication. Once the last one has been
previewed, it will return to preview the
rst.
Click to select a Publication for
listening.
*The Bookshelf button is only active
during Pause Mode.
Use to control the Sleep Timer
function. Each click will sound a different
chime and change the setting as follows:
15 minutes > 30 minutes >
60 minutes > OFF
A 2-second press on will turn the
Sleep Timer off, regardless of the current
setting.
Once set, when the Sleep Timer expires,
a bookmark will be saved and the
CONNECT will turn off silently.
*The Sleep Timer may only be set while in
Pause Mode.
**When the sleep timer is activated,
the LED will blink intermittently during
playback.
*CONNECT saves a bookmark for each
Publication separately.
During continuous press, the CONNECT
will beep each time it skips and the LED
will blink.
*Actual time may vary.
***If CONNECT is turned off before
the timer expires, the sleep timer
is automatically reset to off when
CONNECT restarts.
SOLAR AUDIO PLAYER USER MANUAL
ENVOY
CONNECT
TURNING CONNECT
ON/OFF
SELECTING A
PUBLICATION FOR
PLAYBACK
SLEEP TIMER
Each Publication (book, magazine, etc.)
is subdivided into one or more Sections
(chapters or audio les).
During playback, click or to
jump backward or forward one Section
within the current Publication. If the last
Section is currently playing, a chime will
be played to indicate end of Publication.
If the rst Section is playing, it will restart
from the beginning.
A 2-second press will skip approximately
25 seconds* within the current Section.
A continuous press will continue
skipping until the button is released
or the beginning/end of the Section is
reached.
While in playback, click to
pause playback. The LED will blink
intermittently. To resume, click again.
*If CONNECT is left paused for 5 minutes,
it will automatically turn off.
Bookmarking on the CONNECT is
completely automatic. Whenever paused,
or turned off, CONNECT will bookmark
the current Publication and the current
position within that Publication (minus 3
seconds).
NAVIGATING
DURING PLAYBACK
PAUSING/
BOOKMARKING
When the end of a Publication is
reached, the bookmark is automatically
reset to the beginning of that
Publication.
To manually reset to the beginning of a
Publication, during playback click the
button repetitively until the beginning
of the rst Section is reached. The
bookmark will be saved from that point.
RESETTING A
BOOKMARK TO
THE BEGINNING
While in Pause Mode, a 5-second
continuous press on will delete the
current Publication. Five distinct beeps
will be played to warn the user of the
pending deletion.
Once the publication is deleted, a chime
will be played as conrmation and the
CONNECT will skip to the next available
Publication, preview it and pause.
*Deleting a publication may only be done
while in Pause Mode.
After pausing the CONNECT, press and
hold the and buttons together.
The following occurs:
• The serial number is voiced in
Mandarin (internal QA feature).
• All bookmarks are erased!
• The volume is reset to medium.
• The player is turned off.
*Caution should be exercised when using
this function since all bookmarks will be
erased!
**Erasing all bookmarks resets playback
to the beginning of the rst Publication.
DELETING A
PUBLICATION
RESETTING THE
CONNECT
Press and hold until the LED lights
and a chime sounds. The CONNECT will
turn on, preview the rst Publication (or
the last one played) and then pause.
or
EASY START
1 2 3 4
56789
1/3
Envoy Connect User Manual - A4 - English - 2020.01.15-1.1.2
buttons together for 2 seconds. Playback
will now begin from the card.
While a card is loaded, you may easily
toggle between the card and onboard
memory by pausing playback and
pressing the and buttons again.
When you are browsing Publications
using , after the last Publication from
the onboard memory is previewed,
CONNECT will automatically switch to
microSD playback (if a card is present)
and preview the rst Publication on the
card. Once the last Publication on the
card is previewed, it will automatically
switch back to onboard memory.
To remove** a card, gently push it in.
The reader will unlock and push it out
so you can remove it. If the player was
in Playback Mode from the card when
removed, it will chime and revert to the
onboard memory.
You can view, format and prepare a card
while loaded in CONNECT’s microSD
card reader when it is connected to a
Computer using a USB to micro-USB
cable. You may also do the same with
the card loaded in a microSD adaptor
connected to a Computer.
**A chime is played any time a microSD
card is inserted or removed.
If the battery capacity drops to 5%,
CONNECT will save the current
bookmark and turn itself off.
Plug player into any standard
computer USB port using a “USB to
micro-USB” cable for about 3 hours* or
until the LED stops blinking.
For solar charging, place the player
with the solar panel directly facing
bright sunlight for at least 8 hours*. Note
that the LED will not blink while solar
charging.
*Charging times are approximate and
vary according to the current battery
capacity.
The player will connect with the
computer and the LED will turn on
(communication indication).
While in Computer Communication
mode, pressing will disconnect the
player from Computer Communication
mode, and turn the player on.
In order to reconnect the player in
Computer Communication mode, the
player must be physically disconnected
and then reconnected.
*While connected to the computer, the
player’s battery will be charging.
**Physically disconnecting the player
from the computer will stop the battery
charging.
CHARGING
INSTRUCTIONS
Computer Communication mode is
essential to allow programming of the
CONNECT:
Simply connect the player to the
computer using the “USB – micro USB”
cable. The player will enter Computer
Communication mode.
*If the player was on, the player will turn
off.
CHARGING/
COMMUNICATION
MODES
With proper care, the CONNECT’s
Lithium-Ion battery should perform
well for several years. When shipped,
the battery is only partially charged.
Please fully charge it before the rst use
following one of the charging methods
below:
For fastest charge, connect any
standard “USB” charger (regulated
+5VDC, minimum 300mA) to the micro-
USB port on the bottom of the player
for about 2 hours* or until the LED stops
blinking.
If the battery capacity drops to 10%,
CONNECT will play a special chime every
minute to warn of low-battery and the
LED will blink intermittently.
BATTERY CHECK
• Avoid completely depleting the battery
as this will shorten its overall lifetime
and takes much longer to fully charge
afterwards.
BATTERY CARE
• If sunlight is the only means available
for charging, it is recommended to
leave the player in direct light often
to keep the battery at least partially
charged.
• When not in use and whenever
possible, keep the player in a cool
place, which will also help to preserve
battery life.
• Before stowing the player for
prolonged periods, make sure the
battery is at least partially charged.
• If stored for extended periods, it is
recommended to recharge the player
at least every 6 months, in order to
prevent the battery from losing its
ability to recharge.
• Should the battery become defective
and unable to accept a charge, it is still
possible to operate the player using
a USB cable connected to a computer
or an electric charger. If sunlight is the
only source for power/charging, please
replace the battery.
even after the player is turned off and
restarted.
*Volume adjustment works while in
Playback Mode and Pause Mode. When in
Pause Mode, the player will beep at each
level to indicate the current loudness.
Each CONNECT is identiable by a
unique internal serial number*. For
technical support reasons, the CONNECT
can “voice” the serial number and
rmware revision when needed. While
in Pause Mode, press the and
buttons together to play the information.
*The serial number may also appear on
the label on the back of the player.
VOICING THE
SERIAL NUMBER
Insert earphone or speaker plug into the
auxiliary 3.5mm stereo audio jack on the
bottom of the unit. The internal speaker
will turn off and audio will be output to
the connected device. When the plug is
removed, the internal speaker will turn
back on.
A click on or will decrease/
increase volume one level. A continuous
press will change the loudness until
the minimum/maximum is reached. A
double-beep is played when minimum/
maximum volume is reached.
The CONNECT remembers the current
volume and will remain set at this level
EARPHONES,
SPEAKERS AND
VOLUME
The CONNECT can also play audio from
a properly structured microSD card. With
the player facing you, insert** the card
with the brass contacts showing* until it
locks in place.
*The jagged edge is on the left, the
smooth edge is on the right.
Once a card is loaded, pause playback
then press and hold the and
USING THE
MICROSD CARD
15
1413
16 17 18 19
10 11 12
2/3
Envoy Connect User Manual - A4 - English - 2020.01.15-1.1.2
buttons together for 2 seconds. Playback
will now begin from the card.
While a card is loaded, you may easily
toggle between the card and onboard
memory by pausing playback and
pressing the and buttons again.
When you are browsing Publications
using , after the last Publication from
the onboard memory is previewed,
CONNECT will automatically switch to
microSD playback (if a card is present)
and preview the rst Publication on the
card. Once the last Publication on the
card is previewed, it will automatically
switch back to onboard memory.
To remove** a card, gently push it in.
The reader will unlock and push it out
so you can remove it. If the player was
in Playback Mode from the card when
removed, it will chime and revert to the
onboard memory.
You can view, format and prepare a card
while loaded in CONNECT’s microSD
card reader when it is connected to a
Computer using a USB to micro-USB
cable. You may also do the same with
the card loaded in a microSD adaptor
connected to a Computer.
**A chime is played any time a microSD
card is inserted or removed.
If the battery capacity drops to 5%,
CONNECT will save the current
bookmark and turn itself off.
Plug player into any standard
computer USB port using a “USB to
micro-USB” cable for about 3 hours* or
until the LED stops blinking.
For solar charging, place the player
with the solar panel directly facing
bright sunlight for at least 8 hours*. Note
that the LED will not blink while solar
charging.
*Charging times are approximate and
vary according to the current battery
capacity.
The player will connect with the
computer and the LED will turn on
(communication indication).
While in Computer Communication
mode, pressing will disconnect the
player from Computer Communication
mode, and turn the player on.
In order to reconnect the player in
Computer Communication mode, the
player must be physically disconnected
and then reconnected.
*While connected to the computer, the
player’s battery will be charging.
**Physically disconnecting the player
from the computer will stop the battery
charging.
CHARGING
INSTRUCTIONS
Computer Communication mode is
essential to allow programming of the
CONNECT:
Simply connect the player to the
computer using the “USB – micro USB”
cable. The player will enter Computer
Communication mode.
*If the player was on, the player will turn
off.
CHARGING/
COMMUNICATION
MODES
With proper care, the CONNECT’s
Lithium-Ion battery should perform
well for several years. When shipped,
the battery is only partially charged.
Please fully charge it before the rst use
following one of the charging methods
below:
For fastest charge, connect any
standard “USB” charger (regulated
+5VDC, minimum 300mA) to the micro-
USB port on the bottom of the player
for about 2 hours* or until the LED stops
blinking.
If the battery capacity drops to 10%,
CONNECT will play a special chime every
minute to warn of low-battery and the
LED will blink intermittently.
BATTERY CHECK
• Avoid completely depleting the battery
as this will shorten its overall lifetime
and takes much longer to fully charge
afterwards.
BATTERY CARE
• If sunlight is the only means available
for charging, it is recommended to
leave the player in direct light often
to keep the battery at least partially
charged.
• When not in use and whenever
possible, keep the player in a cool
place, which will also help to preserve
battery life.
• Before stowing the player for
prolonged periods, make sure the
battery is at least partially charged.
• If stored for extended periods, it is
recommended to recharge the player
at least every 6 months, in order to
prevent the battery from losing its
ability to recharge.
• Should the battery become defective
and unable to accept a charge, it is still
possible to operate the player using
a USB cable connected to a computer
or an electric charger. If sunlight is the
only source for power/charging, please
replace the battery.
even after the player is turned off and
restarted.
*Volume adjustment works while in
Playback Mode and Pause Mode. When in
Pause Mode, the player will beep at each
level to indicate the current loudness.
Each CONNECT is identiable by a
unique internal serial number*. For
technical support reasons, the CONNECT
can “voice” the serial number and
rmware revision when needed. While
in Pause Mode, press the and
buttons together to play the information.
*The serial number may also appear on
the label on the back of the player.
VOICING THE
SERIAL NUMBER
Insert earphone or speaker plug into the
auxiliary 3.5mm stereo audio jack on the
bottom of the unit. The internal speaker
will turn off and audio will be output to
the connected device. When the plug is
removed, the internal speaker will turn
back on.
A click on or will decrease/
increase volume one level. A continuous
press will change the loudness until
the minimum/maximum is reached. A
double-beep is played when minimum/
maximum volume is reached.
The CONNECT remembers the current
volume and will remain set at this level
EARPHONES,
SPEAKERS AND
VOLUME
The CONNECT can also play audio from
a properly structured microSD card. With
the player facing you, insert** the card
with the brass contacts showing* until it
locks in place.
*The jagged edge is on the left, the
smooth edge is on the right.
Once a card is loaded, pause playback
then press and hold the and
USING THE
MICROSD CARD
15
1413
16 17 18 19
10 11 12
2/3
Envoy Connect User Manual - A4 - English - 2020.01.15-1.1.2
buttons together for 2 seconds. Playback
will now begin from the card.
While a card is loaded, you may easily
toggle between the card and onboard
memory by pausing playback and
pressing the and buttons again.
When you are browsing Publications
using , after the last Publication from
the onboard memory is previewed,
CONNECT will automatically switch to
microSD playback (if a card is present)
and preview the rst Publication on the
card. Once the last Publication on the
card is previewed, it will automatically
switch back to onboard memory.
To remove** a card, gently push it in.
The reader will unlock and push it out
so you can remove it. If the player was
in Playback Mode from the card when
removed, it will chime and revert to the
onboard memory.
You can view, format and prepare a card
while loaded in CONNECT’s microSD
card reader when it is connected to a
Computer using a USB to micro-USB
cable. You may also do the same with
the card loaded in a microSD adaptor
connected to a Computer.
**A chime is played any time a microSD
card is inserted or removed.
If the battery capacity drops to 5%,
CONNECT will save the current
bookmark and turn itself off.
Plug player into any standard
computer USB port using a “USB to
micro-USB” cable for about 3 hours* or
until the LED stops blinking.
For solar charging, place the player
with the solar panel directly facing
bright sunlight for at least 8 hours*. Note
that the LED will not blink while solar
charging.
*Charging times are approximate and
vary according to the current battery
capacity.
The player will connect with the
computer and the LED will turn on
(communication indication).
While in Computer Communication
mode, pressing will disconnect the
player from Computer Communication
mode, and turn the player on.
In order to reconnect the player in
Computer Communication mode, the
player must be physically disconnected
and then reconnected.
*While connected to the computer, the
player’s battery will be charging.
**Physically disconnecting the player
from the computer will stop the battery
charging.
CHARGING
INSTRUCTIONS
Computer Communication mode is
essential to allow programming of the
CONNECT:
Simply connect the player to the
computer using the “USB – micro USB”
cable. The player will enter Computer
Communication mode.
*If the player was on, the player will turn
off.
CHARGING/
COMMUNICATION
MODES
With proper care, the CONNECT’s
Lithium-Ion battery should perform
well for several years. When shipped,
the battery is only partially charged.
Please fully charge it before the rst use
following one of the charging methods
below:
For fastest charge, connect any
standard “USB” charger (regulated
+5VDC, minimum 300mA) to the micro-
USB port on the bottom of the player
for about 2 hours* or until the LED stops
blinking.
If the battery capacity drops to 10%,
CONNECT will play a special chime every
minute to warn of low-battery and the
LED will blink intermittently.
BATTERY CHECK
• Avoid completely depleting the battery
as this will shorten its overall lifetime
and takes much longer to fully charge
afterwards.
BATTERY CARE
• If sunlight is the only means available
for charging, it is recommended to
leave the player in direct light often
to keep the battery at least partially
charged.
• When not in use and whenever
possible, keep the player in a cool
place, which will also help to preserve
battery life.
• Before stowing the player for
prolonged periods, make sure the
battery is at least partially charged.
• If stored for extended periods, it is
recommended to recharge the player
at least every 6 months, in order to
prevent the battery from losing its
ability to recharge.
• Should the battery become defective
and unable to accept a charge, it is still
possible to operate the player using
a USB cable connected to a computer
or an electric charger. If sunlight is the
only source for power/charging, please
replace the battery.
even after the player is turned off and
restarted.
*Volume adjustment works while in
Playback Mode and Pause Mode. When in
Pause Mode, the player will beep at each
level to indicate the current loudness.
Each CONNECT is identiable by a
unique internal serial number*. For
technical support reasons, the CONNECT
can “voice” the serial number and
rmware revision when needed. While
in Pause Mode, press the and
buttons together to play the information.
*The serial number may also appear on
the label on the back of the player.
VOICING THE
SERIAL NUMBER
Insert earphone or speaker plug into the
auxiliary 3.5mm stereo audio jack on the
bottom of the unit. The internal speaker
will turn off and audio will be output to
the connected device. When the plug is
removed, the internal speaker will turn
back on.
A click on or will decrease/
increase volume one level. A continuous
press will change the loudness until
the minimum/maximum is reached. A
double-beep is played when minimum/
maximum volume is reached.
The CONNECT remembers the current
volume and will remain set at this level
EARPHONES,
SPEAKERS AND
VOLUME
The CONNECT can also play audio from
a properly structured microSD card. With
the player facing you, insert** the card
with the brass contacts showing* until it
locks in place.
*The jagged edge is on the left, the
smooth edge is on the right.
Once a card is loaded, pause playback
then press and hold the and
USING THE
MICROSD CARD
15
1413
16 17 18 19
10 11 12
2/3
Envoy Connect User Manual - A4 - English - 2020.01.15-1.1.2
buttons together for 2 seconds. Playback
will now begin from the card.
While a card is loaded, you may easily
toggle between the card and onboard
memory by pausing playback and
pressing the and buttons again.
When you are browsing Publications
using , after the last Publication from
the onboard memory is previewed,
CONNECT will automatically switch to
microSD playback (if a card is present)
and preview the rst Publication on the
card. Once the last Publication on the
card is previewed, it will automatically
switch back to onboard memory.
To remove** a card, gently push it in.
The reader will unlock and push it out
so you can remove it. If the player was
in Playback Mode from the card when
removed, it will chime and revert to the
onboard memory.
You can view, format and prepare a card
while loaded in CONNECT’s microSD
card reader when it is connected to a
Computer using a USB to micro-USB
cable. You may also do the same with
the card loaded in a microSD adaptor
connected to a Computer.
**A chime is played any time a microSD
card is inserted or removed.
If the battery capacity drops to 5%,
CONNECT will save the current
bookmark and turn itself off.
Plug player into any standard
computer USB port using a “USB to
micro-USB” cable for about 3 hours* or
until the LED stops blinking.
For solar charging, place the player
with the solar panel directly facing
bright sunlight for at least 8 hours*. Note
that the LED will not blink while solar
charging.
*Charging times are approximate and
vary according to the current battery
capacity.
The player will connect with the
computer and the LED will turn on
(communication indication).
While in Computer Communication
mode, pressing will disconnect the
player from Computer Communication
mode, and turn the player on.
In order to reconnect the player in
Computer Communication mode, the
player must be physically disconnected
and then reconnected.
*While connected to the computer, the
player’s battery will be charging.
**Physically disconnecting the player
from the computer will stop the battery
charging.
CHARGING
INSTRUCTIONS
Computer Communication mode is
essential to allow programming of the
CONNECT:
Simply connect the player to the
computer using the “USB – micro USB”
cable. The player will enter Computer
Communication mode.
*If the player was on, the player will turn
off.
CHARGING/
COMMUNICATION
MODES
With proper care, the CONNECT’s
Lithium-Ion battery should perform
well for several years. When shipped,
the battery is only partially charged.
Please fully charge it before the rst use
following one of the charging methods
below:
For fastest charge, connect any
standard “USB” charger (regulated
+5VDC, minimum 300mA) to the micro-
USB port on the bottom of the player
for about 2 hours* or until the LED stops
blinking.
If the battery capacity drops to 10%,
CONNECT will play a special chime every
minute to warn of low-battery and the
LED will blink intermittently.
BATTERY CHECK
• Avoid completely depleting the battery
as this will shorten its overall lifetime
and takes much longer to fully charge
afterwards.
BATTERY CARE
• If sunlight is the only means available
for charging, it is recommended to
leave the player in direct light often
to keep the battery at least partially
charged.
• When not in use and whenever
possible, keep the player in a cool
place, which will also help to preserve
battery life.
• Before stowing the player for
prolonged periods, make sure the
battery is at least partially charged.
• If stored for extended periods, it is
recommended to recharge the player
at least every 6 months, in order to
prevent the battery from losing its
ability to recharge.
• Should the battery become defective
and unable to accept a charge, it is still
possible to operate the player using
a USB cable connected to a computer
or an electric charger. If sunlight is the
only source for power/charging, please
replace the battery.
even after the player is turned off and
restarted.
*Volume adjustment works while in
Playback Mode and Pause Mode. When in
Pause Mode, the player will beep at each
level to indicate the current loudness.
Each CONNECT is identiable by a
unique internal serial number*. For
technical support reasons, the CONNECT
can “voice” the serial number and
rmware revision when needed. While
in Pause Mode, press the and
buttons together to play the information.
*The serial number may also appear on
the label on the back of the player.
VOICING THE
SERIAL NUMBER
Insert earphone or speaker plug into the
auxiliary 3.5mm stereo audio jack on the
bottom of the unit. The internal speaker
will turn off and audio will be output to
the connected device. When the plug is
removed, the internal speaker will turn
back on.
A click on or will decrease/
increase volume one level. A continuous
press will change the loudness until
the minimum/maximum is reached. A
double-beep is played when minimum/
maximum volume is reached.
The CONNECT remembers the current
volume and will remain set at this level
EARPHONES,
SPEAKERS AND
VOLUME
The CONNECT can also play audio from
a properly structured microSD card. With
the player facing you, insert** the card
with the brass contacts showing* until it
locks in place.
*The jagged edge is on the left, the
smooth edge is on the right.
Once a card is loaded, pause playback
then press and hold the and
USING THE
MICROSD CARD
15
1413
16 17 18 19
10 11 12
2/3
Envoy Connect User Manual - A4 - English - 2020.01.15-1.1.2
buttons together for 2 seconds. Playback
will now begin from the card.
While a card is loaded, you may easily
toggle between the card and onboard
memory by pausing playback and
pressing the and buttons again.
When you are browsing Publications
using , after the last Publication from
the onboard memory is previewed,
CONNECT will automatically switch to
microSD playback (if a card is present)
and preview the rst Publication on the
card. Once the last Publication on the
card is previewed, it will automatically
switch back to onboard memory.
To remove** a card, gently push it in.
The reader will unlock and push it out
so you can remove it. If the player was
in Playback Mode from the card when
removed, it will chime and revert to the
onboard memory.
You can view, format and prepare a card
while loaded in CONNECT’s microSD
card reader when it is connected to a
Computer using a USB to micro-USB
cable. You may also do the same with
the card loaded in a microSD adaptor
connected to a Computer.
**A chime is played any time a microSD
card is inserted or removed.
If the battery capacity drops to 5%,
CONNECT will save the current
bookmark and turn itself off.
Plug player into any standard
computer USB port using a “USB to
micro-USB” cable for about 3 hours* or
until the LED stops blinking.
For solar charging, place the player
with the solar panel directly facing
bright sunlight for at least 8 hours*. Note
that the LED will not blink while solar
charging.
*Charging times are approximate and
vary according to the current battery
capacity.
The player will connect with the
computer and the LED will turn on
(communication indication).
While in Computer Communication
mode, pressing will disconnect the
player from Computer Communication
mode, and turn the player on.
In order to reconnect the player in
Computer Communication mode, the
player must be physically disconnected
and then reconnected.
*While connected to the computer, the
player’s battery will be charging.
**Physically disconnecting the player
from the computer will stop the battery
charging.
CHARGING
INSTRUCTIONS
Computer Communication mode is
essential to allow programming of the
CONNECT:
Simply connect the player to the
computer using the “USB – micro USB”
cable. The player will enter Computer
Communication mode.
*If the player was on, the player will turn
off.
CHARGING/
COMMUNICATION
MODES
With proper care, the CONNECT’s
Lithium-Ion battery should perform
well for several years. When shipped,
the battery is only partially charged.
Please fully charge it before the rst use
following one of the charging methods
below:
For fastest charge, connect any
standard “USB” charger (regulated
+5VDC, minimum 300mA) to the micro-
USB port on the bottom of the player
for about 2 hours* or until the LED stops
blinking.
If the battery capacity drops to 10%,
CONNECT will play a special chime every
minute to warn of low-battery and the
LED will blink intermittently.
BATTERY CHECK
• Avoid completely depleting the battery
as this will shorten its overall lifetime
and takes much longer to fully charge
afterwards.
BATTERY CARE
• If sunlight is the only means available
for charging, it is recommended to
leave the player in direct light often
to keep the battery at least partially
charged.
• When not in use and whenever
possible, keep the player in a cool
place, which will also help to preserve
battery life.
• Before stowing the player for
prolonged periods, make sure the
battery is at least partially charged.
• If stored for extended periods, it is
recommended to recharge the player
at least every 6 months, in order to
prevent the battery from losing its
ability to recharge.
• Should the battery become defective
and unable to accept a charge, it is still
possible to operate the player using
a USB cable connected to a computer
or an electric charger. If sunlight is the
only source for power/charging, please
replace the battery.
even after the player is turned off and
restarted.
*Volume adjustment works while in
Playback Mode and Pause Mode. When in
Pause Mode, the player will beep at each
level to indicate the current loudness.
Each CONNECT is identiable by a
unique internal serial number*. For
technical support reasons, the CONNECT
can “voice” the serial number and
rmware revision when needed. While
in Pause Mode, press the and
buttons together to play the information.
*The serial number may also appear on
the label on the back of the player.
VOICING THE
SERIAL NUMBER
Insert earphone or speaker plug into the
auxiliary 3.5mm stereo audio jack on the
bottom of the unit. The internal speaker
will turn off and audio will be output to
the connected device. When the plug is
removed, the internal speaker will turn
back on.
A click on or will decrease/
increase volume one level. A continuous
press will change the loudness until
the minimum/maximum is reached. A
double-beep is played when minimum/
maximum volume is reached.
The CONNECT remembers the current
volume and will remain set at this level
EARPHONES,
SPEAKERS AND
VOLUME
The CONNECT can also play audio from
a properly structured microSD card. With
the player facing you, insert** the card
with the brass contacts showing* until it
locks in place.
*The jagged edge is on the left, the
smooth edge is on the right.
Once a card is loaded, pause playback
then press and hold the and
USING THE
MICROSD CARD
15
1413
16 17 18 19
10 11 12
2/3
Envoy Connect User Manual - A4 - English - 2020.01.15-1.1.2
buttons together for 2 seconds. Playback
will now begin from the card.
While a card is loaded, you may easily
toggle between the card and onboard
memory by pausing playback and
pressing the and buttons again.
When you are browsing Publications
using , after the last Publication from
the onboard memory is previewed,
CONNECT will automatically switch to
microSD playback (if a card is present)
and preview the rst Publication on the
card. Once the last Publication on the
card is previewed, it will automatically
switch back to onboard memory.
To remove** a card, gently push it in.
The reader will unlock and push it out
so you can remove it. If the player was
in Playback Mode from the card when
removed, it will chime and revert to the
onboard memory.
You can view, format and prepare a card
while loaded in CONNECT’s microSD
card reader when it is connected to a
Computer using a USB to micro-USB
cable. You may also do the same with
the card loaded in a microSD adaptor
connected to a Computer.
**A chime is played any time a microSD
card is inserted or removed.
If the battery capacity drops to 5%,
CONNECT will save the current
bookmark and turn itself off.
Plug player into any standard
computer USB port using a “USB to
micro-USB” cable for about 3 hours* or
until the LED stops blinking.
For solar charging, place the player
with the solar panel directly facing
bright sunlight for at least 8 hours*. Note
that the LED will not blink while solar
charging.
*Charging times are approximate and
vary according to the current battery
capacity.
The player will connect with the
computer and the LED will turn on
(communication indication).
While in Computer Communication
mode, pressing will disconnect the
player from Computer Communication
mode, and turn the player on.
In order to reconnect the player in
Computer Communication mode, the
player must be physically disconnected
and then reconnected.
*While connected to the computer, the
player’s battery will be charging.
**Physically disconnecting the player
from the computer will stop the battery
charging.
CHARGING
INSTRUCTIONS
Computer Communication mode is
essential to allow programming of the
CONNECT:
Simply connect the player to the
computer using the “USB – micro USB”
cable. The player will enter Computer
Communication mode.
*If the player was on, the player will turn
off.
CHARGING/
COMMUNICATION
MODES
With proper care, the CONNECT’s
Lithium-Ion battery should perform
well for several years. When shipped,
the battery is only partially charged.
Please fully charge it before the rst use
following one of the charging methods
below:
For fastest charge, connect any
standard “USB” charger (regulated
+5VDC, minimum 300mA) to the micro-
USB port on the bottom of the player
for about 2 hours* or until the LED stops
blinking.
If the battery capacity drops to 10%,
CONNECT will play a special chime every
minute to warn of low-battery and the
LED will blink intermittently.
BATTERY CHECK
• Avoid completely depleting the battery
as this will shorten its overall lifetime
and takes much longer to fully charge
afterwards.
BATTERY CARE
• If sunlight is the only means available
for charging, it is recommended to
leave the player in direct light often
to keep the battery at least partially
charged.
• When not in use and whenever
possible, keep the player in a cool
place, which will also help to preserve
battery life.
• Before stowing the player for
prolonged periods, make sure the
battery is at least partially charged.
• If stored for extended periods, it is
recommended to recharge the player
at least every 6 months, in order to
prevent the battery from losing its
ability to recharge.
• Should the battery become defective
and unable to accept a charge, it is still
possible to operate the player using
a USB cable connected to a computer
or an electric charger. If sunlight is the
only source for power/charging, please
replace the battery.
even after the player is turned off and
restarted.
*Volume adjustment works while in
Playback Mode and Pause Mode. When in
Pause Mode, the player will beep at each
level to indicate the current loudness.
Each CONNECT is identiable by a
unique internal serial number*. For
technical support reasons, the CONNECT
can “voice” the serial number and
rmware revision when needed. While
in Pause Mode, press the and
buttons together to play the information.
*The serial number may also appear on
the label on the back of the player.
VOICING THE
SERIAL NUMBER
Insert earphone or speaker plug into the
auxiliary 3.5mm stereo audio jack on the
bottom of the unit. The internal speaker
will turn off and audio will be output to
the connected device. When the plug is
removed, the internal speaker will turn
back on.
A click on or will decrease/
increase volume one level. A continuous
press will change the loudness until
the minimum/maximum is reached. A
double-beep is played when minimum/
maximum volume is reached.
The CONNECT remembers the current
volume and will remain set at this level
EARPHONES,
SPEAKERS AND
VOLUME
The CONNECT can also play audio from
a properly structured microSD card. With
the player facing you, insert** the card
with the brass contacts showing* until it
locks in place.
*The jagged edge is on the left, the
smooth edge is on the right.
Once a card is loaded, pause playback
then press and hold the and
USING THE
MICROSD CARD
15
1413
16 17 18 19
10 11 12
2/3
Envoy Connect User Manual - A4 - English - 2020.01.15-1.1.2
buttons together for 2 seconds. Playback
will now begin from the card.
While a card is loaded, you may easily
toggle between the card and onboard
memory by pausing playback and
pressing the and buttons again.
When you are browsing Publications
using , after the last Publication from
the onboard memory is previewed,
CONNECT will automatically switch to
microSD playback (if a card is present)
and preview the rst Publication on the
card. Once the last Publication on the
card is previewed, it will automatically
switch back to onboard memory.
To remove** a card, gently push it in.
The reader will unlock and push it out
so you can remove it. If the player was
in Playback Mode from the card when
removed, it will chime and revert to the
onboard memory.
You can view, format and prepare a card
while loaded in CONNECT’s microSD
card reader when it is connected to a
Computer using a USB to micro-USB
cable. You may also do the same with
the card loaded in a microSD adaptor
connected to a Computer.
**A chime is played any time a microSD
card is inserted or removed.
If the battery capacity drops to 5%,
CONNECT will save the current
bookmark and turn itself off.
Plug player into any standard
computer USB port using a “USB to
micro-USB” cable for about 3 hours* or
until the LED stops blinking.
For solar charging, place the player
with the solar panel directly facing
bright sunlight for at least 8 hours*. Note
that the LED will not blink while solar
charging.
*Charging times are approximate and
vary according to the current battery
capacity.
The player will connect with the
computer and the LED will turn on
(communication indication).
While in Computer Communication
mode, pressing will disconnect the
player from Computer Communication
mode, and turn the player on.
In order to reconnect the player in
Computer Communication mode, the
player must be physically disconnected
and then reconnected.
*While connected to the computer, the
player’s battery will be charging.
**Physically disconnecting the player
from the computer will stop the battery
charging.
CHARGING
INSTRUCTIONS
Computer Communication mode is
essential to allow programming of the
CONNECT:
Simply connect the player to the
computer using the “USB – micro USB”
cable. The player will enter Computer
Communication mode.
*If the player was on, the player will turn
off.
CHARGING/
COMMUNICATION
MODES
With proper care, the CONNECT’s
Lithium-Ion battery should perform
well for several years. When shipped,
the battery is only partially charged.
Please fully charge it before the rst use
following one of the charging methods
below:
For fastest charge, connect any
standard “USB” charger (regulated
+5VDC, minimum 300mA) to the micro-
USB port on the bottom of the player
for about 2 hours* or until the LED stops
blinking.
If the battery capacity drops to 10%,
CONNECT will play a special chime every
minute to warn of low-battery and the
LED will blink intermittently.
BATTERY CHECK
• Avoid completely depleting the battery
as this will shorten its overall lifetime
and takes much longer to fully charge
afterwards.
BATTERY CARE
• If sunlight is the only means available
for charging, it is recommended to
leave the player in direct light often
to keep the battery at least partially
charged.
• When not in use and whenever
possible, keep the player in a cool
place, which will also help to preserve
battery life.
• Before stowing the player for
prolonged periods, make sure the
battery is at least partially charged.
• If stored for extended periods, it is
recommended to recharge the player
at least every 6 months, in order to
prevent the battery from losing its
ability to recharge.
• Should the battery become defective
and unable to accept a charge, it is still
possible to operate the player using
a USB cable connected to a computer
or an electric charger. If sunlight is the
only source for power/charging, please
replace the battery.
even after the player is turned off and
restarted.
*Volume adjustment works while in
Playback Mode and Pause Mode. When in
Pause Mode, the player will beep at each
level to indicate the current loudness.
Each CONNECT is identiable by a
unique internal serial number*. For
technical support reasons, the CONNECT
can “voice” the serial number and
rmware revision when needed. While
in Pause Mode, press the and
buttons together to play the information.
*The serial number may also appear on
the label on the back of the player.
VOICING THE
SERIAL NUMBER
Insert earphone or speaker plug into the
auxiliary 3.5mm stereo audio jack on the
bottom of the unit. The internal speaker
will turn off and audio will be output to
the connected device. When the plug is
removed, the internal speaker will turn
back on.
A click on or will decrease/
increase volume one level. A continuous
press will change the loudness until
the minimum/maximum is reached. A
double-beep is played when minimum/
maximum volume is reached.
The CONNECT remembers the current
volume and will remain set at this level
EARPHONES,
SPEAKERS AND
VOLUME
The CONNECT can also play audio from
a properly structured microSD card. With
the player facing you, insert** the card
with the brass contacts showing* until it
locks in place.
*The jagged edge is on the left, the
smooth edge is on the right.
Once a card is loaded, pause playback
then press and hold the and
USING THE
MICROSD CARD
15
1413
16 17 18 19
10 11 12
2/3
Envoy Connect User Manual - A4 - English - 2020.01.15-1.1.2
buttons together for 2 seconds. Playback
will now begin from the card.
While a card is loaded, you may easily
toggle between the card and onboard
memory by pausing playback and
pressing the and buttons again.
When you are browsing Publications
using , after the last Publication from
the onboard memory is previewed,
CONNECT will automatically switch to
microSD playback (if a card is present)
and preview the rst Publication on the
card. Once the last Publication on the
card is previewed, it will automatically
switch back to onboard memory.
To remove** a card, gently push it in.
The reader will unlock and push it out
so you can remove it. If the player was
in Playback Mode from the card when
removed, it will chime and revert to the
onboard memory.
You can view, format and prepare a card
while loaded in CONNECT’s microSD
card reader when it is connected to a
Computer using a USB to micro-USB
cable. You may also do the same with
the card loaded in a microSD adaptor
connected to a Computer.
**A chime is played any time a microSD
card is inserted or removed.
If the battery capacity drops to 5%,
CONNECT will save the current
bookmark and turn itself off.
Plug player into any standard
computer USB port using a “USB to
micro-USB” cable for about 3 hours* or
until the LED stops blinking.
For solar charging, place the player
with the solar panel directly facing
bright sunlight for at least 8 hours*. Note
that the LED will not blink while solar
charging.
*Charging times are approximate and
vary according to the current battery
capacity.
The player will connect with the
computer and the LED will turn on
(communication indication).
While in Computer Communication
mode, pressing will disconnect the
player from Computer Communication
mode, and turn the player on.
In order to reconnect the player in
Computer Communication mode, the
player must be physically disconnected
and then reconnected.
*While connected to the computer, the
player’s battery will be charging.
**Physically disconnecting the player
from the computer will stop the battery
charging.
CHARGING
INSTRUCTIONS
Computer Communication mode is
essential to allow programming of the
CONNECT:
Simply connect the player to the
computer using the “USB – micro USB”
cable. The player will enter Computer
Communication mode.
*If the player was on, the player will turn
off.
CHARGING/
COMMUNICATION
MODES
With proper care, the CONNECT’s
Lithium-Ion battery should perform
well for several years. When shipped,
the battery is only partially charged.
Please fully charge it before the rst use
following one of the charging methods
below:
For fastest charge, connect any
standard “USB” charger (regulated
+5VDC, minimum 300mA) to the micro-
USB port on the bottom of the player
for about 2 hours* or until the LED stops
blinking.
If the battery capacity drops to 10%,
CONNECT will play a special chime every
minute to warn of low-battery and the
LED will blink intermittently.
BATTERY CHECK
• Avoid completely depleting the battery
as this will shorten its overall lifetime
and takes much longer to fully charge
afterwards.
BATTERY CARE
• If sunlight is the only means available
for charging, it is recommended to
leave the player in direct light often
to keep the battery at least partially
charged.
• When not in use and whenever
possible, keep the player in a cool
place, which will also help to preserve
battery life.
• Before stowing the player for
prolonged periods, make sure the
battery is at least partially charged.
• If stored for extended periods, it is
recommended to recharge the player
at least every 6 months, in order to
prevent the battery from losing its
ability to recharge.
• Should the battery become defective
and unable to accept a charge, it is still
possible to operate the player using
a USB cable connected to a computer
or an electric charger. If sunlight is the
only source for power/charging, please
replace the battery.
even after the player is turned off and
restarted.
*Volume adjustment works while in
Playback Mode and Pause Mode. When in
Pause Mode, the player will beep at each
level to indicate the current loudness.
Each CONNECT is identiable by a
unique internal serial number*. For
technical support reasons, the CONNECT
can “voice” the serial number and
rmware revision when needed. While
in Pause Mode, press the and
buttons together to play the information.
*The serial number may also appear on
the label on the back of the player.
VOICING THE
SERIAL NUMBER
Insert earphone or speaker plug into the
auxiliary 3.5mm stereo audio jack on the
bottom of the unit. The internal speaker
will turn off and audio will be output to
the connected device. When the plug is
removed, the internal speaker will turn
back on.
A click on or will decrease/
increase volume one level. A continuous
press will change the loudness until
the minimum/maximum is reached. A
double-beep is played when minimum/
maximum volume is reached.
The CONNECT remembers the current
volume and will remain set at this level
EARPHONES,
SPEAKERS AND
VOLUME
The CONNECT can also play audio from
a properly structured microSD card. With
the player facing you, insert** the card
with the brass contacts showing* until it
locks in place.
*The jagged edge is on the left, the
smooth edge is on the right.
Once a card is loaded, pause playback
then press and hold the and
USING THE
MICROSD CARD
15
1413
16 17 18 19
10 11 12
2/3
Envoy Connect User Manual - A4 - English - 2020.01.15-1.1.2
buttons together for 2 seconds. Playback
will now begin from the card.
While a card is loaded, you may easily
toggle between the card and onboard
memory by pausing playback and
pressing the and buttons again.
When you are browsing Publications
using , after the last Publication from
the onboard memory is previewed,
CONNECT will automatically switch to
microSD playback (if a card is present)
and preview the rst Publication on the
card. Once the last Publication on the
card is previewed, it will automatically
switch back to onboard memory.
To remove** a card, gently push it in.
The reader will unlock and push it out
so you can remove it. If the player was
in Playback Mode from the card when
removed, it will chime and revert to the
onboard memory.
You can view, format and prepare a card
while loaded in CONNECT’s microSD
card reader when it is connected to a
Computer using a USB to micro-USB
cable. You may also do the same with
the card loaded in a microSD adaptor
connected to a Computer.
**A chime is played any time a microSD
card is inserted or removed.
If the battery capacity drops to 5%,
CONNECT will save the current
bookmark and turn itself off.
Plug player into any standard
computer USB port using a “USB to
micro-USB” cable for about 3 hours* or
until the LED stops blinking.
For solar charging, place the player
with the solar panel directly facing
bright sunlight for at least 8 hours*. Note
that the LED will not blink while solar
charging.
*Charging times are approximate and
vary according to the current battery
capacity.
The player will connect with the
computer and the LED will turn on
(communication indication).
While in Computer Communication
mode, pressing will disconnect the
player from Computer Communication
mode, and turn the player on.
In order to reconnect the player in
Computer Communication mode, the
player must be physically disconnected
and then reconnected.
*While connected to the computer, the
player’s battery will be charging.
**Physically disconnecting the player
from the computer will stop the battery
charging.
CHARGING
INSTRUCTIONS
Computer Communication mode is
essential to allow programming of the
CONNECT:
Simply connect the player to the
computer using the “USB – micro USB”
cable. The player will enter Computer
Communication mode.
*If the player was on, the player will turn
off.
CHARGING/
COMMUNICATION
MODES
With proper care, the CONNECT’s
Lithium-Ion battery should perform
well for several years. When shipped,
the battery is only partially charged.
Please fully charge it before the rst use
following one of the charging methods
below:
For fastest charge, connect any
standard “USB” charger (regulated
+5VDC, minimum 300mA) to the micro-
USB port on the bottom of the player
for about 2 hours* or until the LED stops
blinking.
If the battery capacity drops to 10%,
CONNECT will play a special chime every
minute to warn of low-battery and the
LED will blink intermittently.
BATTERY CHECK
• Avoid completely depleting the battery
as this will shorten its overall lifetime
and takes much longer to fully charge
afterwards.
BATTERY CARE
• If sunlight is the only means available
for charging, it is recommended to
leave the player in direct light often
to keep the battery at least partially
charged.
• When not in use and whenever
possible, keep the player in a cool
place, which will also help to preserve
battery life.
• Before stowing the player for
prolonged periods, make sure the
battery is at least partially charged.
• If stored for extended periods, it is
recommended to recharge the player
at least every 6 months, in order to
prevent the battery from losing its
ability to recharge.
• Should the battery become defective
and unable to accept a charge, it is still
possible to operate the player using
a USB cable connected to a computer
or an electric charger. If sunlight is the
only source for power/charging, please
replace the battery.
even after the player is turned off and
restarted.
*Volume adjustment works while in
Playback Mode and Pause Mode. When in
Pause Mode, the player will beep at each
level to indicate the current loudness.
Each CONNECT is identiable by a
unique internal serial number*. For
technical support reasons, the CONNECT
can “voice” the serial number and
rmware revision when needed. While
in Pause Mode, press the and
buttons together to play the information.
*The serial number may also appear on
the label on the back of the player.
VOICING THE
SERIAL NUMBER
Insert earphone or speaker plug into the
auxiliary 3.5mm stereo audio jack on the
bottom of the unit. The internal speaker
will turn off and audio will be output to
the connected device. When the plug is
removed, the internal speaker will turn
back on.
A click on or will decrease/
increase volume one level. A continuous
press will change the loudness until
the minimum/maximum is reached. A
double-beep is played when minimum/
maximum volume is reached.
The CONNECT remembers the current
volume and will remain set at this level
EARPHONES,
SPEAKERS AND
VOLUME
The CONNECT can also play audio from
a properly structured microSD card. With
the player facing you, insert** the card
with the brass contacts showing* until it
locks in place.
*The jagged edge is on the left, the
smooth edge is on the right.
Once a card is loaded, pause playback
then press and hold the and
USING THE
MICROSD CARD
15
1413
16 17 18 19
10 11 12
2/3
Envoy Connect User Manual - A4 - English - 2020.01.15-1.1.2
buttons together for 2 seconds. Playback
will now begin from the card.
While a card is loaded, you may easily
toggle between the card and onboard
memory by pausing playback and
pressing the and buttons again.
When you are browsing Publications
using , after the last Publication from
the onboard memory is previewed,
CONNECT will automatically switch to
microSD playback (if a card is present)
and preview the rst Publication on the
card. Once the last Publication on the
card is previewed, it will automatically
switch back to onboard memory.
To remove** a card, gently push it in.
The reader will unlock and push it out
so you can remove it. If the player was
in Playback Mode from the card when
removed, it will chime and revert to the
onboard memory.
You can view, format and prepare a card
while loaded in CONNECT’s microSD
card reader when it is connected to a
Computer using a USB to micro-USB
cable. You may also do the same with
the card loaded in a microSD adaptor
connected to a Computer.
**A chime is played any time a microSD
card is inserted or removed.
If the battery capacity drops to 5%,
CONNECT will save the current
bookmark and turn itself off.
Plug player into any standard
computer USB port using a “USB to
micro-USB” cable for about 3 hours* or
until the LED stops blinking.
For solar charging, place the player
with the solar panel directly facing
bright sunlight for at least 8 hours*. Note
that the LED will not blink while solar
charging.
*Charging times are approximate and
vary according to the current battery
capacity.
The player will connect with the
computer and the LED will turn on
(communication indication).
While in Computer Communication
mode, pressing will disconnect the
player from Computer Communication
mode, and turn the player on.
In order to reconnect the player in
Computer Communication mode, the
player must be physically disconnected
and then reconnected.
*While connected to the computer, the
player’s battery will be charging.
**Physically disconnecting the player
from the computer will stop the battery
charging.
CHARGING
INSTRUCTIONS
Computer Communication mode is
essential to allow programming of the
CONNECT:
Simply connect the player to the
computer using the “USB – micro USB”
cable. The player will enter Computer
Communication mode.
*If the player was on, the player will turn
off.
CHARGING/
COMMUNICATION
MODES
With proper care, the CONNECT’s
Lithium-Ion battery should perform
well for several years. When shipped,
the battery is only partially charged.
Please fully charge it before the rst use
following one of the charging methods
below:
For fastest charge, connect any
standard “USB” charger (regulated
+5VDC, minimum 300mA) to the micro-
USB port on the bottom of the player
for about 2 hours* or until the LED stops
blinking.
If the battery capacity drops to 10%,
CONNECT will play a special chime every
minute to warn of low-battery and the
LED will blink intermittently.
BATTERY CHECK
• Avoid completely depleting the battery
as this will shorten its overall lifetime
and takes much longer to fully charge
afterwards.
BATTERY CARE
• If sunlight is the only means available
for charging, it is recommended to
leave the player in direct light often
to keep the battery at least partially
charged.
• When not in use and whenever
possible, keep the player in a cool
place, which will also help to preserve
battery life.
• Before stowing the player for
prolonged periods, make sure the
battery is at least partially charged.
• If stored for extended periods, it is
recommended to recharge the player
at least every 6 months, in order to
prevent the battery from losing its
ability to recharge.
• Should the battery become defective
and unable to accept a charge, it is still
possible to operate the player using
a USB cable connected to a computer
or an electric charger. If sunlight is the
only source for power/charging, please
replace the battery.
even after the player is turned off and
restarted.
*Volume adjustment works while in
Playback Mode and Pause Mode. When in
Pause Mode, the player will beep at each
level to indicate the current loudness.
Each CONNECT is identiable by a
unique internal serial number*. For
technical support reasons, the CONNECT
can “voice” the serial number and
rmware revision when needed. While
in Pause Mode, press the and
buttons together to play the information.
*The serial number may also appear on
the label on the back of the player.
VOICING THE
SERIAL NUMBER
Insert earphone or speaker plug into the
auxiliary 3.5mm stereo audio jack on the
bottom of the unit. The internal speaker
will turn off and audio will be output to
the connected device. When the plug is
removed, the internal speaker will turn
back on.
A click on or will decrease/
increase volume one level. A continuous
press will change the loudness until
the minimum/maximum is reached. A
double-beep is played when minimum/
maximum volume is reached.
The CONNECT remembers the current
volume and will remain set at this level
EARPHONES,
SPEAKERS AND
VOLUME
The CONNECT can also play audio from
a properly structured microSD card. With
the player facing you, insert** the card
with the brass contacts showing* until it
locks in place.
*The jagged edge is on the left, the
smooth edge is on the right.
Once a card is loaded, pause playback
then press and hold the and
USING THE
MICROSD CARD
15
1413
16 17 18 19
10 11 12
2/3
Envoy Connect User Manual - A4 - English - 2020.01.15-1.1.2
Other manuals for Connect
1
Table of contents
Other Envoy Media Player manuals
