EOS FUTURO-SD4 User manual

1
3x screwsBracketMonitor
It is very important to install and operate this product according to the following
instructions. Failure to do so may render your guarantee void.
1. The Monitor includes following items:
● 1x monitor ● 1x adapter ● 1x bracket for the monitor
● 3x screws ● 3x plastics plug ● 1x TF card (MicroSD)
FUTURO VIDEO DOORPHONE
Monitor
Model : FUTURO-SD4 (Photo Memory feature / GUI)
FUTURO-SD4B (No Photo Memory feature)
Door Station
Model : FUTURO-CZ4 (Surface mount )
FUTURO-CP4 (Flush Mount)
Adapter 3x plastics plug TF card
(SD4 Model only)
Instruction Manual
www.eos.com.au

2. Monitor
2.1 Description
2
2.2. Installation
Mount the bracket on the wall with screws and do the wiring according to
the wiring diagram in next page.
Power
Image Recording(SD4 only)
Melody Mute
Talk
Monitoring
Door Open
Interphone
Menu/OK
/left
/right
Return
Microphone
1 2 3
ø8mm
Connect necessary wires to the terminal and mount the monitor on the bracket.
4
TF Card slot (FUTURO-SD4 Only)
1.5M
Dimension (WxHxD): 235x128x25mm

3. Door Station
3.1 Description
2
1. Microphone
2. LEDs for Night vision
3. Speaker
4. Call button
5. Camera
6. Terminals
A : Audio
G : Ground
B : 12V DC from Monitor
V : Video to Monitor
D/O : Door Open
M+ : DC Power for automatic recording
by motion detection
7. Microphone Sensitivity Adjustment
8. Speaker Volume Adjustment
2
4
3
1
52
4
3
1
5
6
8
7
FUTURO-CZ4 FUTURO-CP4

3.2 Door Station Installation
150Cm
With Weatherhood
( Optional )
Overall Dimension
(W/H/D)
99 x 148 x 28 mm
3.2.1 FUTURO-CZ4
4
150Cm

3.2.2 FUTURO-CP4
150Cm
Cover Plate
Dimension (W/H/D)
128x182x4 mm
Embedding Box
Dimension (W/H/D)
98x155x55 mm
5

6
4. Wiring diagrams
4.1. Typical diagram #1: One outdoor station with one monitor(FUTURO-SD4/4B)
Outdoor Station Monitor
Lock
4.2. Typical diagram #2: One outdoor station with two indoor monitors
Monitor A
Monitor B
Outdoor Station
Lock
Power
Supply
for Lock
OUTDOOR 1
M+
V
B
G
A
G
D
A
V
A G B V D/O D/O MD+
A G B V D/O D/O M+
Power
Supply
for Lock
13V DC 1.2A
13V DC 1.2A
13V DC 1.2A

7
4.3. Typical diagram #3: 3 outdoor stations with 4 monitors
(with FUTURO-CPU4)
-
+
Electric Lock
Power Supply
for Electric Lock
6 wires
4 wires
4 wires
&
M+ wire
4 wires
Futuro-CZ/CP4
Camera#1 Camera#2 Camera#3 DC13V 3Amp
Power Supply for
FUTURO-CPU4
5 wires
Camera Terminal description
A Audio 4.6VDC when standy, 12V DC when Door Open
G Ground 0V
B B+ 12V DC power from Monitor
V Video Composit Video signal to Monitor
D/O Door Open Dry contact output for Electrical Door Strike
M+ Motion+ Optional 12V DC from Monitor for Automatic Recoding
by Motion Detection. Only available to Camera#1
FUTURO-CPU4
6 wires 6 wires 6 wires

8
Monitor Terminal description
V Video Standby:0V, When monitor is On:appx 0.5V DC
A Audio Standby:appx 4.6VDC
When talking :appx 3.6VDC, When Door open:appx 12VDC
D Data Data signal between Monitors, Cameras and CPU4
+ - Power 13V DC power for Monitor / G Ground
Note:
●0-50 meters, the cable size should be at least 0.5 mm²
●50-100 meters, the cable size should be at least 0.75 mm²
●Max. working distance is 100 meters.
5. How to use:
5.1. To the right / To the left / Menu (OK) / Return
1 2 3 4

9
5.2. Calling / Talking / Unlocking
Press the “Call” button
on the outdoor station
The calling sound rings from
indoor monitors with visitor’s image
shown on the screen
5
Photo icon
When the video icon appears ( in
Video mode), the monitor will take
a video and the time for video can
be set in the Mode. (SD4 Model Only)
When the photo icon appears, the
monitor will automatically take two
photos. (SD4 Model Only)
Video icon
Press the ‘Door Open’ button
to open the door for visitors.
6 7
Press the ‘ Talk’ button to talk with
visitors. Press ‘Talk’ again and you
can end the call.
Talking time:about 120Sec

10
5.3. Monitoring
8
Press the ‘Monitoring’ button to see the
entrance and press again to exit the
monitoring mode. But when there are
more than one outdoor stations, press
“Monitoring” to see the entrance from
one outdoor station and press again to
see from next outdoor station.
Press again to exit the monitoring mode.
9
Monitoring time: After 40 sec, the
monitor will switch to standby mode.
During the monitoring, if there is a
visitor, you can press “Talk” to talk.
10
When the system has more than one
outdoor stations, after any outdoor
station is called, the monitor will auto-
matically memorise the door station is
exist. It will show the door when next
time Monitoring. To reset and show only
one door station when motoring, press
the ‘Talk’ button for 4 seconds.

Interphone
Interphone
button
11
12
5.4.
5.5. Mute mode
5.6. Automatic recording by motion detection (SD4 Model only)
In standby mode, the device will take a video automatically with 10 seconds interval
when the system detects a motion.
* MD+ terminal MUST be connected for this feature.
* When there are more than one door station in the system with FUTURO-CPU4,
this feature is only available to the very first door station.
When you press ’Interphone’ on one
monitor, the other monitor in the
house will ring.
13
To answer, press ‘Talk’ button on the called monitor.
Press ‘Talk’ again to end the talking.
Mute indicator light on
11
During the standby mode, long press
“Door Open” button for 4s to mute
the ringtone. To un-mute, just long
press ‘Door Open’ button again
for 4 sec.
Calling Monitor Called Monitor
Calling Monitor Called Monitor

Press “Unlock’’ to confirm
and exit.
Press ”Talk” button to
adjust the ringtone volume.
5.7. Ringtone adjustment ( SD4B Model ONLY )
14
15 16
Long press ”Monitoring’’ button
for 4 seconds to enter ringtone
selection. If you need to change
the ringtone,just press ”Monitoring’’
button once again.
12
* See Page 15 for FUTURO-SD4 Ringtone adjustment.

19
18
17
5.8 Brightness / Color / Talking volume setting ( SD4B Model ONLY )
When the monitor is turned on, press ”Menu ”button and “BRIGHTNESS...”
will show on the screen. If you need to adjust the brightness, please press
When you press”Menu ”for the second time, “COLOR...”will show on the
screen. If you need to adjust the color, please press
When you press”Menu ” for the third time, “VOLOME...”will show on the
screen. If you need to adjust the talking volume, please press
Press “Menu ”again to save and exit .
13
* See Page 15 for FUTURO-SD4 Brightness / Color / Volume adjustment.

14
6. GUI Menu setting (FUTURO-SD4 Model Only)
In standby, press any button at the right hand side to enter the menu and press
‘Left/Right’ button to select the required icon.
6.1. Date and time setting
6.1.1. Select ‘Date and time’ and then press ‘OK’.
Setup
Video
checking
Date and
time setting
Photo
checking
6.1.2. Press ‘OK’ to select the required icon and then press ‘left/right’ to adjust the
values, press ‘return’ to save and exit.
Lorem ipsum

15
6.2. SETUP
Press ‘left/right’ to select ‘Setup’ icon, and then press ‘OK’ to confirm and access
the selected setting. Select ‘Screen’ icon and press ‘OK’ to enter next menu.
6.3. SCREEN
Press ‘OK’ to select ‘color’, ‘brightness’ or ‘Speaker volume’ icon, and then press
‘left/right’ to adjust the values, press ‘return’ to save and exit.
6.4. RINGTONE
6.4.1. Press ‘left/right’ to select ‘Ringtone’, and then press ‘OK’ to confirm and
access the selected setting.

16
6.5. LANGUAGE
6.5.1. Press ‘left/right’ to select ‘Language’, and then press ‘OK’ to confirm and
access the selected setting.
6.4.2. Press ‘OK’ to select the required icon, and then press ‘left/rignt’ to adjust the
ringtone volume, press ‘OK’ to save and exit.
6.4.3. Press ‘OK’ to select the required icon, and then press ‘left/rignt’ to select the
ringtone, press ‘OK’ to save and exit.

17
6.5.2. Press ‘left/right’ to select ‘Language’, and then press ‘OK’ to save and exit.
6.6. UNLOCK TIMING (Default 1 second)
6.6.1. Press ‘left/right’ to select ‘Unlock timing’, and then press ‘OK’ to confirm
and access the selected setting.
6.6.2. Press ‘left/right’ to adjust the values, and then press ‘OK’ or ‘return’ to save
and exit.

18
6.7.3. Press ‘Enter’ to select the required icon and then press ‘left/right’ to change
the values, press ‘OK’ to save and exit. The values are the duration of the
video recorded when motion detection and the video when calling.
6.7. MODE
6.7.1. Press ‘left/right’ to select ‘Mode’, and then press ‘OK’ to confirm and access
the selected setting.
6.7.2. Press ‘OK’ to select the required icon, and then press ‘left/rignt’ to select
‘Video’ or ‘Photo’ mode, press ‘OK’ to save and exit.

19
6.8.3. Press ‘OK’ to select the required icon, press ‘left/right’ to select ‘Yes’, and
then press ‘OK’ and the selection is validated. Or press ‘return’ to exit
directly.
6.8. RESET
6.8.1. Press ‘left/right’ to select ‘RESET’, and then press ‘OK’ to confirm and access
the selected setting.
6.8.2. Press ‘OK’ to select the required icon, and then press ‘left/right’ to select
‘Format TF’ or ‘Reset’.

20
6.9. PHOTO
6.9.1. Press ‘left/right’ to select ‘Photo’ and then press ‘OK’ to enter next menu.
6.9.2. Menu with no recorded photo.
6.9.3. If photo recorded, press ‘left/right’ to check the photos.