Epever RTU 2G A User manual

HUIZHOU EPEVER TECHNOLOGY CO., LTD TEL: [phone] Website: www.epever.com
12
GPRS Transmission Terminal
EPEVER RTU 2G A
1. Important Safety Instructions
Read the instructions and warnings in the manual carefully before
installation.
The product should be situated away from the rain, exposure, dust,
vibration, corrosion, and intense electromagnetic environment.
Please avoid water and other liquids enter into the product.
Never use the product at sites where electrostatic could occur, and avoid
the antenna close to a metal object.
DO NOT disassemble or attempt to repair the product.
Power supply: DC 9~60V or 5V, it can be customized according to
customers' requirements.
Enable GPRS service for the SIM card before installation.
2. Overview
EPEVER RTU 2G A is a new wireless data transmission terminal based on
the GPRS network. With the GSM/GPRS SIM card, the connected devices
can easily access the EPEVER cloud server to realize remote, wireless, and
networked communication. EPEVER RTU 2G A is suitable for EPEVER solar
controller, inverter, and inverter/charger.
Features:
Extensive network coverage and flexible networking
Low operating costs (charged by network flow)
Adopt a non-standard DB9 male terminal
Embedded in Modbus RTU protocol
Automatic restore after disconnection
Support RS485 communication
3. Appearance
★The pin definition of the terminal(DB9 female) connected to the DB9
male terminal❸ is as follows.
Indicators
You can observe the indicators' color and status through the hole❷.
Name
Color
Status
Instruction
Network indicator
(LED2)
Red
On solid
Correct power supply
Unregistered GPRS network
Slowly flashing (5s)
Registered GPRS network
successfully
Sync. Indicator
(LED1)
Green
Slowly flashing (5s)
Registered GPRS network
successfully
Power indicator
(LED2)
Green
Turn off after a
flashing
Correct power supply
4. Parameter Configuration
Step1: Connect the DB9 terminal ❸to the PC through a DB9 to USB adapter.
Note: Connect an external power adapter to the DB9 female terminal to supply the
EPEVER RTU 2G A.
Step2: Insert the SIM card and power on the EPEVER RTU 2G A. For detailed
SIM card installation, refer to chapter 6, Installation.
Step3: Open the configuration tool on the PC and click the "connect" button
to connect the EPEVER RTU 2G A successfully.
Step4: Click the "Read" and "Write" buttons to configure the parameter.
Step5: After configuring, power on the product again to make the modified
parameters take effect.
Common configuration parameters:
Parameters
Configuration
Server Info
No modifications are recommended
APN
Different countries have different APN, and please make sure APN
firstly. Products will not be connected to the Internet with fault APN.
China APN: CMNET
APN User
Enter it according to the actual
APN Key
Enter it according to the actual
Baud
Set it according to the connected controller or inverter
5. System Connection
EPEVER RTU 2G A can be applied to the following solar street light systems.
Through a GPRS signal, users can easily monitor the operating status and
modify the related parameters on the Cloud platform.
Note: The EPEVER RTU 2G A supports 5~18V DC power. While a larger transient
current is needed when the wireless network sends the data, it is suggested to
adopt a power adapter of DC 5V/500mA or above.
6. Installation
Step1: Install the SIM Card
① Purchase a SIM card and activate the GPRS service.
② Undo the three screws from the EPEVER RTU 2G A.
③ Push the shell upward and take out the circuit board.
④ Take out the small SIM card and insert it into the card slot correctly.
⑤ After installing successfully, reinstall the product shell.
Step2: Install the silicone pad
Tear off the silicone pad's adhesive and stick the silicone pad to the DB9
terminal of the EPEVER RTU 2G A.
Step3: Install the antenna
Connect the 4G antenna to the antenna port of the EPEVER RTU 2G A.
※Thanks for selecting the EPEVER RTU 2G A solar wireless collector.
Please read this manual carefully before using the product.
※ Please keep this manual for future reference.
❶Antenna port
❸DB9 male connector★
❹Fixing screws
Item
Terminal
Definition
1/2
NC
Floating
3
VCC2
Power2 (12V/200mA)
4
GND2
Power GND2
5
GND1
Power GND1
6
NC
Floating
7
RS485-A
RS485-A
8
RS485-B
RS485-B
9
VCC1
Power1 (5V/400mA)
❷Hole

HUIZHOU EPEVER TECHNOLOGY CO., LTD TEL: [phone] Website: www.epever.com
34
Caution: As a wireless terminal, keep the antenna away from the human body as far
as possible during the operation process.
Step4: Connect the controller
Connect the EPEVER RTU 2G A to the controller's com. port through a DB9
adapter.
7. Applications
According to different applications, the cloud platform provides two networking
connection methods: "one-to-one" and "one-to-more." Controllers can be
added into the system convenient and flexible by the two methods. Users can
remote control or real-time monitor the controller through the cloud platform.
One-To-One connection
One-To-more connection
After adding the device into the Cloud platform successfully, log in to the cloud
platform (https://iot.epsolarpv.com), remotely monitor the real-time condition
or set the parameters.
Note: For new accounts, devices need to be manually added in the EPEVER cloud
before monitoring.
8. Specifications
Item
Specifications
Network type
GPRS class12
Coding method
CS1 – CS4(Comply with SMG31bis)
Frequency
GSM850/EGSM900/DCS1800/PCS1900MHz
GPRS transmission rate
85.6kbps
Network protocol
TCP/UDP/FTP/PPP/DNS
SIM card voltage
3V/1.8V
Antenna connector
50Ω IPX connector
Serial port level type
RS485
Serial port baud
9600~115200bps
Power
DC: 9~ 60VDC or 5VDC
Power consumption
Communication: <200mA/5V; Idle: <40mA/5V
Environment temperature
-40~85℃
Humidity
0~95%(Non-condensing)
Electromagnetic
compatibility
Electrostatic discharge immunity test, level 3
Anti-interference test, level 3
9. Troubleshooting
Faults
Solutions
LED indicator OFF
1. Check whether the power supply is correct.
2. Check whether the power supply's poles are connected
inversely. The EPEVER RTU 2G A is equipped with anti-
reverse protection. The reverse connection does not
cause fatal damage. However, it affects the regular use
before the correct connection is restored.
Network indicator
ON solid
After power is on, the network indicator is on solid in 60
seconds. If it still cannot flash after 60 seconds, please check:
1. Check whether the SIM card is inserted correctly.
2. Check whether the GPRS service is activated.
Network indicator on solid again after running for a while:
1. Check whether the server status is normal.
2. Check whether the SIM card is loose or arrear.
Smoke emits with a
pungent smell
The actual voltage exceeds the rated voltage, causing the
internal components to burn out. Don't hesitate to contact the
supplier in time and send it to the manufacturer.
Unregister on the
network
1. Check whether the SIM card is inserted correctly.
2. Check whether the SIM card has activated the GPRS
service.
3. Check whether the input power is sufficient. Input power
should be 12VDC/0.2A or 5VDC/0.2A.
Parameters can't be
configured
1. Check whether the connection to the PC is correct.
2. Check whether the serial port selection is correct.
10. Dimension
Any changes without prior notice! Version number: 3.2