Epson PowerLite 8000i Specification sheet

EPSON®Multimedia Projector
1
2
Connecting to a
PC
Laptop
To use your remote control as a mouse or to use audio,follow these steps:
Connecting to a
Macintosh®
PowerBook®
Connect one end of the
projector video cable to
the projector’s
Computer 1port.
1Connect the round end
of the main cable to the
projector’s Mouse/Com 1
port.
2Connect the PS/2 or USB
cable to the MOUSE terminal
on the main cable.
3
4
Connect the other end of
the PS/2 or USB cable to
the mouse or USB port
on your laptop.
To use audio,connect one end of the
audio cable to the projector’sAudio 1
jack and the other end to your laptop.
If you want to use the remote control as a mouse, see below.
If not, just follow the steps in “UsingYour Projector” (see other side).
Connect the round end
of the main cable to
the projector’s
Mouse/Com 1port.
Connect the Mac or USB cable to the
MOUSE terminal on the main cable.
Connect the other end
of the video cable to the
laptop’s monitor port.
Connect one end of
the projector video cable
to the projector’s
Computer 1port.
Connect the small terminal of the desktop adapter to
the other end of the projector video cable.(Be sure
the desktop adapter DIP switches are set correctly for
the resolution you want.See your PowerBook manual.)
1
2
1
2
Connect the other end of the
Mac or USB cable to the mouse
or USB port on your PowerBook.
3
4To use audio,connect one end of the audio
cable to the projector’sAudio 1jack and
the other end to your PowerBook.
3
If you want to use the remote control as a mouse, see below.
If not, just follow the steps in “UsingYour Projector” (see other side).
Make sure your EPSON®PowerLite®projector and computer are turned off. Then follow these steps:
Connect the projector video cable
(with Macintosh desktop adapter attached)
to the video-out port of your PowerBook.
3Connect the power cord
to the projector.
desk
desktop adapter
video-out
cable
video-out
cable
main cable
Quick Setup
desktop
adapter
4Connect the power cord
to the projector.
main cable
Optional Connections
To use your remote control as a mouse or use audio,follow these steps:
Optional Connections
Note: If your PowerBook requires
a video-out cable (not included),
connect the smaller end of the cable to
the video-out port on the back of the
PowerBook.Then connect the other end
to the desktop adapter.
EPSON PowerLite 8000i
EPSON PowerLite 9000i

Projector at a Glance
EPSON and PowerLite are registered trademarks of SEIKO EPSON CORPORATION.
Copyright © 1999 by Epson America, Inc. CPD 9113
UsingYour Projector
Computer
Switches connected
computer sources
sequentially
Menu
Displays or hides the menu
Power button
Turns projector
on and off
- Volume +
Adjusts the volume
when used in
conjunction with
the Shift button
Power
Starts or stops
the projector
Freeze
Freezes the computer
or video image
A/V Mute
Turns off the
audio-video
E-Zoom
Enlarges or reduces
the image size
RC on/off
Turns the
remote control
on or off
Illumination
Illuminates all buttons
on the remote control
Esc
Ends the
current function;
returns to previous
menu/screen;
acts as a right
mouse-click when the
image source is
Computer
A/V Mute
Turns off the audio-video
Focus ring
Zoom ring
Foot adjust levers
Help
Displays the projector’s
online help
Resize
Provides display
options for multiple
resolutions
Video
Switches to the
video input source
Esc
Ends the current function;
returns to previous
screen/menu
Enter button
Registers a menu selection
Effects buttons
(1-5)
Display pre-
programmed
special effects
Enter (Pointer)
Navigates menu system;
acts as a mouse pointer;
acts as a left mouse-click
when the image source
is Computer
1. Plug in the projector. The power light on the projector’s control panel
turns orange.(The projector is not on yet.)
2. Remove the lens cap.
3. Press the Power button on the control panel or remote control
once to turn on. The power light flashes green as the projector
warms up. Then turn on your computer.
Warning: Never look into the lens when the lamp is on.
4. You can set the display to appear on both the computer’s screen and
the projector.Check your computer manual for instructions.
5. To adjust the projected image size,rotate the zoom (outside) ring
on the projector.For larger adjustments,you may need to
reposition the projector closer to or farther from the screen.
6. To focus the image, rotate the focus (inside) ring.
7. If the image is too high or low,lift up the foot adjust levers to raise
or lower the adjustable feet.Release the levers to lock the feet
in place.
8. When you want to stop projecting images,press the Power button
again.The projection light flashes orange as the projector cools down.
When you are done, make sure the projection light has stopped
flashing and then unplug the power cord.
Caution: Never unplug the power cord when the power light
is green; this may damage the lamp.
Control panel
Menu
Comp1
S-Video
Auto
P in P
- Volume +
Help
BNC
Video
Resize
Preset
- Keystone +
Adjusts a trapezoid
image to a normal rectangle
For instructions on setting up your projector with a desktop computer or for information
on using the ELP Link IV software to control the projector,see your User’s Guide.
Using the Remote Control
Using the Control Panel
EPSON
ESC
O
P
E
N
Infrared
receiver
Tracking +,Tracking -
(right and left arrows)
Adjusts projector to
match the computer signal
Sync +, Sync -
(up and down arrows)
Adjusts projector to
match the computer signal
Optical keystone
adjustment knob
EPSON PowerLite 8000i
EPSON PowerLite 9000i