Epson EMP-6100 User manual

EMP Monitor
Operation Guide

1
Meanings of symbols used
Indicates something that may cause injury or damage to the projector.
Indicates information that is related to a topic or which may be useful to know.
Indicates a page where a related topic or more a detailed explanation is provided.
[ (Name) ] Indicates the name of a projector port or a computer menu or item name.
Example: [InputA] [Start]
CAUTION
TIP

2
Contents
Meanings of symbols used 1
Operating Environment 3
Compatible computers ............................................................ 3
Before starting operations .......................................................3
Registering projectors for monitoring 4
Registration using automatic detection ................................... 5
Registration using IP address (Manual registration) ............... 6
Editing the manually-registered projector list .......................... 7
Deleting a projector from the projector list............................... 7
Main EMP Monitor window 8
Button functions....................................................................... 8
Understanding the projector list............................................... 9
Displaying detailed information ............................................. 10
A projector cannot be monitored or controlled using
EMP Monitor 11
Appendices 12

3
Operating Environment
You can display status information on a computer screen for multiple
projectors that are connected to a network and also carry out batch operations
on all projectors such as turning the power on and off and changing the image
source. A maximum of 64 projectors can be monitored and controlled by batch
operations.
System configuration example
Compatible computers
* Macintosh computers cannot be used.
Before starting operations
Check the following points before starting up EMP Monitor.
• EMP Monitor must be installed in the computer to be used for monitoring
and control.
• The computer and the projectors must be connected to the network.
• If using Windows 2000, NT4.0 or XP, the computer must be started up in
Administrator mode.
(When using EMP-81/61)
• To use EMP Monitor, an adapter and cable for conversion are required.
sUser's Guide "Standby mode"
• You need to make a setting for the adapter before connecting it to the
projector. sThe adapter's documentation
Refer to the "Appendices" for details about the adapter setting. sp.12
Projector A
Projector B
Projector C
Turn on
projector B
EMP Monitor
TIP
If the projector's "Network Monitoring" or "Standby Mode"
configuration menu is set to "ON" or "Network ON", the projector
can still be monitored when it is in standby mode (when the (Power)
indicator is lit orange).
OS* 98SE/Me/NT4.0/2000 Professional/XP Home Edition/XP
Professional
CPU Pentium MMX 166 MHz or higher (Pentium II 233 MHz
or higher recommended)
Memory
capacity
64 MB or more (128 MB or more recommended)
Free hard disk
space
6 MB or more
Display XGA (1024×768) or higher resolution, 16 bit or higher
display colour

4
Registering projectors for monitoring
This operation is carried out when starting EMP Monitor for the first time after
it has been installed and when you would like to add projectors. Once a
projector has been registered, the status for the projector will be displayed
automatically each time EMP Monitor is started from that point onwards.
PROCEDURE
Click [Start] - [Programs] (or [All Programs]) - [EPSON
Projector] - [EMP Monitor] in that order to start EMP
Monitor.
Click [Register projector].
The [Register projector] dialogue box will be displayed.
Use the "Registration using automatic detection" (sp.5) or
"Registration using IP address (Manual registration)" (sp.6)
procedure to register projectors.
1
2
Click to add a projector to be monitored

5
Registering projectors for monitoring
Registration using automatic detection
PROCEDURE
Click [Auto detect] in the [Register projector]
dialogue box.
Select the projector(s) to be registered, and then click
[Add].
You can select several projectors at the same time.
If a projector does not appear in the list, use "Registration using
IP address (Manual registration)". sp.6
Click [Close] to return to the main EMP Monitor
window.
Refer to "Main EMP Monitor window" for details on using the
main window. sp.8
1
2
TIP
• Projectors that have been registered using automatic detection will be
re-detected on the basis of projector name and the IP addresses for
these projectors will be displayed each time EMP Monitor is started.
• If a password entry screen is displayed, enter the password for the
projector's Administrator and then click [OK].
If more than one projector was selected, the password entry screens
for each projector will be displayed in succession.
3

6
Registering projectors for monitoring
Registration using IP address (Manual registration)
PROCEDURE
Click [Manual registration] in the [Register projector]
dialogue box.
Enter the IP address for the projector to be registered
in the [IP address] box, and then click [Confirm].
If a projector with the specified IP address is found on the
network, the projector's name will be displayed, so check that it
is the target projector. If it is not the target projector, re-enter
the IP address.
When using EMP-81/61
The following "Manually register projector" window will be
displayed.
Complete the form and click [Confirm].
Click [Add].
1
2
Projector name Enter the projector name of up to 16
alphanumeric characters, from 0 to 9
and from A(a) to Z(z) and - . You cannot
use a numeric-only name.
IP address Enter the IP address of the projector.
Use Serial⇔TCP/IP
conversion adaptor.
Check the box.
Port Number Enter the port number.
Enter the projector name.
Enter the IP address.
Enter the port number.
Click to check the box.
3
TIP
If a password entry screen is displayed, enter the password for the
projector's Administrator and then click [OK].

7
Registering projectors for monitoring
Editing the manually-registered projector list
Use the following procedure to change the projector name or IP address for
projectors that have been registered manually.
PROCEDURE
Select the projector to be edited in the [Register
projector] dialogue box, and then click [Edit].
If the projector name has changed, simply click
[Confirm].
If the IP address has changed, enter the new IP
address and then click [Confirm].
Check that the projector name is correct.
Click [Update].
Deleting a projector from the projector list
Select the projector to be deleted from the list in the
[Register projector] dialogue box, and then click [Delete].
More than one projector can be selected at the same time.
1
2
3

8
Main EMP Monitor window
The main window shows the status information for each projector. To carry
our operations for projectors, select the projectors from the projector list and
then click the buttons.
To close the window, click the in the top-right corner.
Button functions
The power can be turned on or off and the input source can be changed for
the projectors that are selected from the projector list. The same operations
can also be carried out using the commands in the [Tools] menu.
Buttons
Projector list
Detail display Shows detailed information for the selected projectors.
Power ON Turns the projector power on.
Power OFF Turns the projector power off.
PC1,
InputA
Switches to the input source connected to the
[Computer] port, [Computer1] port or [InputA] port.
PC2,
InputB
Switches to the input source connected to the
[Computer2] port or [InputB] port.
BNC Switches to the input source connected to the [BNC]
port.
S-Video Switches to the input source connected to the
[S-Video] port.
Video Switches to the input source connected to the [Video]
port.
D4 Switches to the input source connected to the [D4]
port.
DVI,
HDMI
Switches to the input source connected to the [DVI]
port or [HDMI] port.
EasyMP Switches to EasyMP or EasyMP.net.
TIP
Some connected projectors may not be equipped with all of the above
ports or functions. If you click a button for a port or function that is
not available, nothing will happen.

9
Main EMP Monitor window
Understanding the projector list
The projector list uses the following icons to show the projector statuses.
The projector information that is generated when a problem is detected is
stored until EMP Monitor is closed. The EMP Monitor displays will not be
updated automatically even if the projector status returns to normal. Click
[Refresh] in the main window to update the status.
Status: Shows the projector status.
Power on and normal status
Power off and normal status
Power on and abnormal status
Power off and abnormal status
Network error (such as not connected to network or
power cord not connected)
Name: Shows the projector name.
Source: Shows the selected image source.
Computer, Computer1 or InputA
Computer2 or InputB
S-Video
Video
D4 (Digital)
DVI or HDMI (Digital)
Error information: Uses the following icons to show the status if an
error occurs with a projector.
End of lamp life warning
Replace with a new lamp.
s"Replacing the Lamp"
in the "Replacing
Consumables" section of
the accessory User's Guide.
Lamp problem "Reading the Indicators"
sRefer to the
"Troubleshooting" section
of the accessory User's
Guide and carry out the
suggested remedy.
High internal temperature
(overheating)
Temperature warning
Internal problem
Fan problem
Temperature sensor
problem