Epson Stylus Pro 10000 Series User manual

Fiery Spark™Professional
EPSON Stylus®Pro 5500
EPSON Stylus®Pro 10000
Installation Guide
Printed on recycled paper.

ii |
Copyright © 2001 by Epson America, Inc.
All rights reserved. No part of this publication may be reproduced, stored in a retrieval system, or
transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or
otherwise, without the prior written permission of SEIKO EPSON CORPORATION. The
information contained herein is designed only for use with these EPSON printers. EPSON is not
responsible for any use of this information as applied to other printers.
Trademarks
EPSON and EPSON Stylus are registered trademarks of SEIKO EPSON CORPORATION.
EPSON Preferred is a service mark of Epson America, Inc.
General Notice: Other product names used herein are for identification purposes only and may
be trademarks of their respective owners. EPSON disclaims any and all rights in those marks.
Legal Notices
Neither SEIKO EPSON CORPORATION nor its affiliates shall be liable to the purchaser of
this product or third parties for damages, losses, costs, or expenses incurred by purchaser or third
parties as a result of: accident, misuse, or abuse of this product or unauthorized modifications,
repairs, or alterations to this product, or (excluding the U.S.) failure to strictly comply with
SEIKO EPSON CORPORATION’s operating and maintenance instructions.
SEIKO EPSON CORPORATION shall not be liable for any damages or problems arising from
the use of any options or any consumable products other than those designated as Original
EPSON Products or EPSON Approved Products by SEIKO EPSON CORPORATION.
Part Number: CPD-12826
Printed in USA 8/01

|iii
Contents
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Where To Get Help . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
System Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Server . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Windows Client Computer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Macintosh Client Computer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Server Software Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Installing the Fiery Spark Server Software . . . . . . . . . . . . . . . . . . . . . . . 4
Installing Command WorkStation . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Enabling File and Printer Sharing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Enabling AppleTalk Protocol . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Hardware Key Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Windows Client Software Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Installing the PostScript Printer Driver for Windows Me . . . . . . . . . . . 8
Installing the PostScript Printer Driver for Windows 2000 . . . . . . . . . . 9
Creating Shortcuts to the Fiery Spark Drop Folders . . . . . . . . . . . . . . 11
Installing Command WorkStation . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Macintosh Client Software Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Installing Printer Files . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Installing Fonts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Creating Shortcuts to the Fiery Spark Drop Folders . . . . . . . . . . . . . . 15
Installing Fiery Spooler . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Installing Fiery Downloader . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Installing ColorWise Pro Tools . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Selecting TCP/IP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Printing to the Fiery Spark . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Notices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
FCC Compliance Statement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

Introduction
This guide provides basic installation instructions for the Fiery Spark™
Professional software in a client-server configuration. Fiery Spark Professional
includes a System Software CD-ROM, a User Software CD-ROM, and a USB
hardware key.
For instructions on using the Fiery Spark software, see the manuals in the
Documentation > English folder on the User Software CD-ROM. You have a
Getting Started Guide, Configuration Guide, Printing Guide, Job Management
Guide, and Color Guide.
These manuals are in PDF format. If you don’t have Adobe®Acrobat®Reader™
for viewing the manual, you can install it by double-clicking the ar405eng
icon in the Documentation folder on the User Software CD-ROM.
Where To Get Help
EPSON provides technical support and information on the installation,
configuration, and operation of professional graphics arts products through the
EPSON Preferred Protection Plan. Call [phone], 6 AM to 8 PM, Pacific
Time, Monday through Friday, and 7 AM to 4 PM, Pacific Time, Saturday.
Before you call, make sure you have your Unit ID number, which is included
with the EPSON Preferred Protection Plan information that came with your
printer. You’ll also need your printer serial number and proof of purchase. If
you experience difficulty using your Unit ID number when accessing the
toll-free EPSON Preferred phone number, please call [phone] in the
U.S. or [phone] in Canada during normal business hours.
Note Do not misplace your hardware key. Lost keys are not covered under
your warranty.
Note If you are using the EPSON®Color Calibrator, make sure you are
using software version 2.1 or later. This version can be downloaded
from http://support.epson.com.
SM

2|Installation Guide
EPSON also provides technical assistance 24 hours a day through the World
Wide Web. You can reach EPSON Support at http://support.epson.com. At
this site, you can download drivers and other files, look at product
documentation, access troubleshooting information, and receive technical
advice through e-mail.
System Requirements
Before you install the software, make sure your computer meets the minimum
system requirements listed below.
Server
•Pentium®4 1.2GHz (1.7GHz recommended)
•Windows®2000 Professional
•256MB RAM (512MB RAM recommended)
•At least 200MB free hard disk space to install the software and at least 1GB
free disk space for processing files (4GB or more available hard disk space
recommended)
•USB connection for EPSON Stylus®Pro 5500 or IEEE-1394 PCI card
(OHCI compliant) connection for EPSON Stylus Pro 10000
•Netscape®Communicator®version 4.5 or 4.7 with Java enabled, or
Microsoft®Internet Explorer version 5.0 or 5.5 with Java enabled, for
Fiery WebTools
•A TCP/IP-enabled network and the IP address or computer name for the
Fiery Spark server
•File and Printer Sharing for Microsoft Network enabled for PC clients
•AppleTalk®Protocol enabled for Macintosh clients
Note Windows 2000 Server is recommended if you have more than
10 users printing concurrently, require support for SMP with more
than 2 CPUs, or require greater fault tolerance

Macintosh Client Computer |3
Windows Client Computer
•Pentium II processor (Pentium III or higher recommended)
•Windows 98, Me, 2000, or Windows NT®4.0 with Service Pack 5 or later
•128MB RAM (256MB or more recommended)
•PostScript®printer driver for Windows
•Windows 98 and Me: Adobe PostScript Printer Driver version 4.3.1
•Windows 2000: Microsoft PostScript Printer Driver for Windows
2000 (included with the Windows 2000 operating system)
•Windows NT: Adobe PostScript Printer Driver version 5.1.2
•For Windows 98 and Me, you also need TCP/IP networking protocol
enabled
•For Windows NT 4.0 and Windows 2000, you also need TCP/IP or
AppleTalk networking protocol enabled
Macintosh Client Computer
•Macintosh®G3, G4, or iMac™(G4 recommended)
•System 8.6 through 9.1
•450MHz or faster processor
•256MB RAM (512MB recommended)
•AppleTalk networking protocol enabled

4|Installation Guide
Server Software Installation
Before you begin, make sure you’ve:
•Connected the printer to the server
•Installed the EPSON printer driver (see your EPSON printer
documentation for instructions)
•Installed the IEEE-1394 driver if you’re using the EPSON Stylus
Pro 10000 (the driver is on the CD-ROM that came with your printer; for
installation instructions, see the Product Support Bulletin at
http://support.epson.com)
•Closed all open programs and turned off any virus protection programs.
Install the following software on the server:
•Fiery Spark Server software (see below)
•Command WorkStation (page 5)
Installing the Fiery Spark Server Software
Follow these steps:
1. Insert the Fiery Spark System Software CD-ROM in your CD-ROM or
DVD drive.
2. Double-click My Computer, then double-click the CD-ROM
icon.
3. Double-click the Setup icon in Fiery folder, then click Next.
4. Follow the on-screen instructions.
Note Use a short server name (8 characters or less). Otherwise, you won’t
be able to see the server name and print queue in the Chooser on
Macintosh clients.
Do not install the hardware key until after all the software is installed.

Installing Command WorkStation |5
5. When you see this screen, select your printer model; then click Next to
continue the installation.
6. Click OK at the end of the installation. Your computer restarts.
Installing Command WorkStation
This installation also installs ColorWise Pro Tools and Fiery Downloader.
Follow these steps:
1. On the Fiery Spark User Software CD-ROM, open the CStation folder.
2. Double-click the Setup icon.
3. Follow the instructions on screen.
4. Click Finish at the end of the installation. Your computer restarts.
5. Configure Command WorkStation as described in the next section.

6|Installation Guide
Configuring Command WorkStation
1. If Command WorkStation is open, click OK.
Otherwise, go to Start > Programs > Command WorkStation, then
click Command WorkStation.
2. Enter the appropriate information for the Fiery Spark, then click Add:
3. Make sure the printer name is selected in the Devices list, then click OK.
4. Select the printer name in the list
of Available Servers, then click OK.
enter PRO10K for the
Stylus Pro 10000 (dye
ink), PRO10KCF for
the Stylus Pro 10000
(pigment ink), or
PRO5500 for the
Stylus Pro 5500
the Nickname can be
different from the Fiery
Spark server name, but
cannot contain
[ ] _ " ' <space> <tab>
This example uses
EPSON as the
nickname.
enter localhost
click Add

Enabling AppleTalk Protocol |7
Enabling File and Printer Sharing
If you have Windows clients, you must enable File and Printer Sharing on the
server. Follow these steps:
1. From the Control Panel, double-click Networks and Dial-up
Connections, then double-click Local Area Connection.
2. Click the Properties button.
3. Click Install.
4. Click Service, then click Add.
5. Select File and Printer Sharing for Microsoft Networks, then click OK.
6. Close any open windows, then restart your computer.
Enabling AppleTalk Protocol
If you have Macintosh clients, you must enable AppleTalk Protocol on the
server. Follow these steps:
1. From the Control Panel, double-click Networks and Dial-up
Connections, then double-click Local Area Connection.
2. Click the Properties button.
3. Click Install.
4. Click Protocol, then click Add.
5. Select AppleTalk Protocol, then click OK.
6. Close any open windows, then restart your computer.